This is my config script for the MMnet1001 module from Propox.
Øyvind Harboe schreef:
Could you post your config scripts?
## Chip:
set CHIPNAME at91sam9260
set CPUTAPID 0x0792603f
set ENDIAN little
source [find target/at91sam9260.cfg]
$_TARGETNAME configure -event reset-init {at91sam_init}
proc at91sam_init { } {
# at reset chip runs at 32 kHz => 1/8 * 32 kHz = 4 kHz
jtag_rclk 4
# Enable user reset and disable watchdog
mww 0xfffffd08 0xa5000501 # RSTC_MR : enable user reset
mww 0xfffffd44 0x00008000 # WDT_MR : disable watchdog
# Oscillator setup
mww 0xfffffc20 0x00004001 # CKGR_MOR : enable the main
oscillator (18.432 MHz)
sleep 20 # wait 20 ms
mww 0xfffffc30 0x00000001 # PMC_MCKR : switch to main oscillator
sleep 10 # wait 10 ms
# now we are running at 18.432 MHz kHz => 1/8 * 18.432 MHz = 2.304 MHz
jtag_rclk 2000
mww 0xfffffc28 0x2060bf09 # CKGR_PLLAR: Set PLLA Register for
198,656MHz
sleep 20 # wait 20 ms
mww 0xfffffc2c 0x207c3f0c # CKGR_PLLBR: Set PLLB Register for
USB usage (USB_CLK = 48 MHz)
sleep 10 # wait 10 ms
mww 0xfffffc30 0x00000101 # PMC_MCKR : Select prescaler
sleep 10 # wait 10 ms
mww 0xfffffc30 0x00000102 # PMC_MCKR : Clock from PLLA is
selected
sleep 10 # wait 10 ms
# now we are running at 198.656 MHz kHz => full speed jtag
jtag_rclk 30000
arm7_9 dcc_downloads enable # Enable faster DCC downloads
# Configure PIO Controller for SDRAM data-lines D16-D31
# PC16-PC31 = Peripheral A: D16-D32
mww 0xfffff844 0xffff0000 # Interrupt Disable
mww 0xfffff854 0xffff0000 # Multi-Drive Disable
mww 0xfffff860 0xffff0000 # Pull-Up Disable
mww 0xfffff870 0xffff0000 # PIO_ASR : Select peripheral A
function for D15..D31
mww 0xfffff804 0xffff0000 # PIO_PDR : Disable PIO function for
D15..D31 (Peripheral function enable)
mww 0xfffffc10 0x00000010 # Enable PIO-C Clock in PMC (PID=4)
# SD-Ram setup
mww 0xffffef1c 0x2 # EBI_CSA : Assign EBI Chip
Select 1 to SDRAM
mww 0xffffea08 0x85227259 # SDRAMC_CR : Configure SDRAM
(IS42S32160A: 4M Words x 32 Bits x 4 Banks (512-Mbit))
mww 0xffffea00 0x1 # SDRAMC_MR : issue a NOP
command
mww 0x20000000 0
mww 0xffffea00 0x2 # SDRAMC_MR : issue an 'All
Banks Precharge' command
mww 0x20000000 0
mww 0xffffea00 0x4 # SDRAMC_MR : issue an
'Auto-Refresh' command (1st)
mww 0x20000000 0
mww 0xffffea00 0x4 # SDRAMC_MR : issue an
'Auto-Refresh' command (2nd)
mww 0x20000000 0
mww 0xffffea00 0x4 # SDRAMC_MR : issue an
'Auto-Refresh' command (3th)
mww 0x20000000 0
mww 0xffffea00 0x4 # SDRAMC_MR : issue an
'Auto-Refresh' command (4th)
mww 0x20000000 0
mww 0xffffea00 0x4 # SDRAMC_MR : issue an
'Auto-Refresh' command (5th)
mww 0x20000000 0
mww 0xffffea00 0x4 # SDRAMC_MR : issue an
'Auto-Refresh' command (6th)
mww 0x20000000 0
mww 0xffffea00 0x4 # SDRAMC_MR : issue an
'Auto-Refresh' command (7th)
mww 0x20000000 0
mww 0xffffea00 0x4 # SDRAMC_MR : issue an
'Auto-Refresh' command (8th)
mww 0x20000000 0
mww 0xffffea00 0x3 # SDRAMC_MR : issue a 'Load
Mode Register' command
mww 0x20000000 0
mww 0xffffea00 0x0 # SDRAMC_MR : Normal Mode
mww 0x20000000 0
mww 0xFFFFEA04 0x30d # SDRAM Refresh Time Register
# datasheet:
8k refresh cycles / 64 ms
# MCLK /
(8*1024 / 64e-3) = 100e6 / 128000 = 781 = 0x30d
}
_______________________________________________
Openocd-development mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/openocd-development
