Nothing changed.
*Cable work fine with DIR-320 router
Open On-Chip Debugger 0.4.0 (2010-10-12-21:17)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.berlios.de/doc/doxygen/bugs.html
parport port = 0x0
25 kHz
jtag_nsrst_delay: 260
jtag_ntrst_delay: 0
trst_and_srst separate srst_gates_jtag trst_push_pull srst_open_drain
Info : pxa270.cpu: hardware has 2 breakpoints and 2 watchpoints
Info : clock speed 25 kHz
Info : JTAG tap: pxa270.cpu tap/device found: 0x79265013 (mfg: 0x009, part:
0x9265, ver: 0x7)
Info : accepting 'gdb' connection from 0
Warn : acknowledgment received, but no packet pending
undefined debug reason 6 - target needs reset
Warn : target not halted
Warn : target not halted
Warn : target not halted
Warn : target not halted
Warn : target not halted
Warn : target not halted
Warn : target not halted
Warn : target not halted
Warn : target not halted
Info : JTAG tap: pxa270.cpu tap/device found: 0x79265013 (mfg: 0x009, part:
0x9265, ver: 0x7)
Warn : keep_alive() was not invoked in the 1000ms timelimit. GDB alive
packet not sent! (1094). Workaround: increase "set remotetimeout" in GDB
target state: halted
target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x800000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
(processor reset)
Info : JTAG tap: pxa270.cpu tap/device found: 0x79265013 (mfg: 0x009, part:
0x9265, ver: 0x7)
Warn : Bad value '00' captured during DR or IR scan:
Warn : check_value: 0x02
Warn : check_mask: 0x07
Error: JTAG error while writing DCSR
Warn : Bad value '00' captured during DR or IR scan:
Warn : check_value: 0x02
Warn : check_mask: 0x07
Error: JTAG error while writing DCSR
Warn : keep_alive() was not invoked in the 1000ms timelimit. GDB alive
packet not sent! (1074). Workaround: increase "set remotetimeout" in GDB
Warn : Bad value '00' captured during DR or IR scan:
Warn : check_value: 0x02
Warn : check_mask: 0x07
Error: JTAG error while writing DCSR
Warn : Bad value '00' captured during DR or IR scan:
Warn : check_value: 0x02
Warn : check_mask: 0x07
Error: JTAG error while writing DCSR
Warn : Bad value '00' captured during DR or IR scan:
Warn : check_value: 0x02
Warn : check_mask: 0x06
Error: JTAG error while reading TX
error while polling TX register, reset CPU
target state: halted
target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x800000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
(processor reset)
2010/10/16 Austin, Alex <[email protected]>
> Try it slower. Try 25kHz to start and see how that goes.
>
> Oleg Kravchenko <[email protected]> wrote:
>
>
> Hello!
>
> I am assemble this cable
> http://downloads.amilda.org/MODs/JTAG/wiggler.gifand I want try
> openocd with my pocket pc based on pxa270 cpu, but I can't
> setup proper config file and as result I am received lots of errors :(
> Help please!
>
> # cat openocd.cfg
> interface parport
> parport_port 0
> parport_cable wiggler2
> jtag_khz 100
>
> if { [info exists CHIPNAME] } {
> set _CHIPNAME $CHIPNAME
> } else {
> set _CHIPNAME pxa270
> }
>
> if { [info exists ENDIAN] } {
> set _ENDIAN $ENDIAN
> } else {
> set _ENDIAN little
> }
>
> if { [info exists CPUTAPID ] } {
> set _CPUTAPID $CPUTAPID
> } else {
> set _CPUTAPID 0x79265013
> }
>
> jtag_nsrst_delay 260
> jtag_ntrst_delay 0
>
> reset_config trst_and_srst separate
>
> set _TARGETNAME $_CHIPNAME.cpu
> jtag newtap $_CHIPNAME cpu -irlen 7 -ircapture 0x1 -irmask 0x7f
> -expected-id
> $_CPUTAPID
>
> target create $_TARGETNAME xscale -endian $_ENDIAN -chain-position
> $_TARGETNAME -variant pxa27x
>
> # maps to PXA internal RAM. If you are using a PXA255
> # you must initialize SDRAM or leave this option off
> #_TARGETNAME configure -work-area-phys 0x5c000000 -work-area-size 0x10000
> -work-area-backup 0
>
> # openocd
> Open On-Chip Debugger 0.4.0 (2010-10-12-21:17)
> Licensed under GNU GPL v2
> For bug reports, read
> http://openocd.berlios.de/doc/doxygen/bugs.html
> parport port = 0x0
> 100 kHz
> jtag_nsrst_delay: 260
> jtag_ntrst_delay: 0
> trst_and_srst separate srst_gates_jtag trst_push_pull srst_open_drain
> Info : pxa270.cpu: hardware has 2 breakpoints and 2 watchpoints
> Info : clock speed 100 kHz
> Info : JTAG tap: pxa270.cpu tap/device found: 0x79265013 (mfg: 0x009, part:
> 0x9265, ver: 0x7)
> Info : accepting 'gdb' connection from 0
> Warn : acknowledgment received, but no packet pending
> undefined debug reason 6 - target needs reset
> Warn : target not halted
> Warn : target not halted
> Warn : target not halted
> Warn : target not halted
> Warn : target not halted
> Warn : target not halted
> Warn : target not halted
> Warn : target not halted
> Warn : target not halted
> Info : JTAG tap: pxa270.cpu tap/device found: 0x79265013 (mfg: 0x009, part:
> 0x9265, ver: 0x7)
> target state: halted
> target halted in ARM state due to debug-request, current mode: Supervisor
> cpsr: 0x880000d3 pc: 0x00000000
> MMU: disabled, D-Cache: disabled, I-Cache: disabled
> (processor reset)
> Warn : Bad value '01' captured during DR or IR scan:
> Warn : check_value: 0x02
> Warn : check_mask: 0x06
> Error: JTAG error while reading TX
> error while polling TX register, reset CPU
> Error: time out writing RX register
> Error: time out writing RX register
> Error: time out writing RX register
> Warn : Bad value '01' captured during DR or IR scan:
> Warn : check_value: 0x02
> Warn : check_mask: 0x06
> Error: JTAG error while writing RX
> Error: time out writing RX register
> Error: time out writing RX register
> Error: time out writing RX register
> Error: time out writing RX register
> Error: time out writing RX register
> _______________________________________________
> Openocd-development mailing list
> [email protected]
> https://lists.berlios.de/mailman/listinfo/openocd-development
>
_______________________________________________
Openocd-development mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/openocd-development
