On Fri, Aug 12, 2011 at 10:04 PM, Xiaofan Chen <[email protected]> wrote:
> Then I came across this one thread in Sparkfun. The change seems
> to make sense as well so I gave it a try.
> http://forum.sparkfun.com/viewtopic.php?f=18&t=24946
>
> It does not seem to help either.
>
> But then I find out actually my V8 J-Link works once in about 3 times for
> EK-LM3S1968 demo board. It works even though that there are still
> quite a bit of error message but it seems to work.
>
> With the on-board TI/Luminary interface, OpenOCD always works.
>
Then I also check out V3/V6/V7 and they all work fine.
D:\work\openocd\openocd_0.5.0_mingw\bin>openocd.exe -f ek-lm3s1968_jlink.cfg
Open On-Chip Debugger 0.5.0 (2011-08-11-13:48)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.berlios.de/doc/doxygen/bugs.html
Warn : Adapter driver 'jlink' did not declare which transports it allows; assumi
ng legacy JTAG-only
Info : only one transport option; autoselect 'jtag'
500 kHz
Info : J-Link initialization started / target CPU reset initiated
Info : J-Link compiled Feb 20 2006 18:20:20 -- Update --
Info : J-Link caps 0x3
Info : J-Link hw version 30000
Info : J-Link hw type J-Link
Info : Vref = 3.290 TCK = 1 TDI = 1 TDO = 1 TMS = 1 SRST = 0 TRST = 255
Info : J-Link JTAG Interface ready
Info : clock speed 500 kHz
Info : JTAG tap: lm3s1968.cpu tap/device found: 0x3ba00477 (mfg: 0x23b, part: 0x
ba00, ver: 0x3)
Info : lm3s1968.cpu: hardware has 6 breakpoints, 4 watchpoints
D:\work\openocd\openocd_0.5.0_mingw\bin>openocd.exe -f ek-lm3s1968_jlink.cfg
Open On-Chip Debugger 0.5.0 (2011-08-11-13:48)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.berlios.de/doc/doxygen/bugs.html
Warn : Adapter driver 'jlink' did not declare which transports it allows; assumi
ng legacy JTAG-only
Info : only one transport option; autoselect 'jtag'
500 kHz
Info : J-Link initialization started / target CPU reset initiated
Info : J-Link ARM V6 compiled Feb 1 2011 14:28:14
Info : J-Link caps 0x99ff7bbf
Info : J-Link hw version 60000
Info : J-Link hw type J-Link
Info : J-Link max mem block 8864
Info : J-Link configuration
Info : USB-Address: 0xff
Info : Kickstart power on JTAG-pin 19: 0xffffff01
Info : Vref = 3.209 TCK = 1 TDI = 0 TDO = 1 TMS = 0 SRST = 0 TRST = 0
Info : J-Link JTAG Interface ready
Info : clock speed 500 kHz
Info : JTAG tap: lm3s1968.cpu tap/device found: 0x3ba00477 (mfg: 0x23b, part: 0x
ba00, ver: 0x3)
Info : lm3s1968.cpu: hardware has 6 breakpoints, 4 watchpoints
D:\work\openocd\openocd_0.5.0_mingw\bin>openocd.exe -f ek-lm3s1968_jlink.cfg
Open On-Chip Debugger 0.5.0 (2011-08-11-13:48)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.berlios.de/doc/doxygen/bugs.html
Warn : Adapter driver 'jlink' did not declare which transports it allows; assumi
ng legacy JTAG-only
Info : only one transport option; autoselect 'jtag'
500 kHz
Info : J-Link initialization started / target CPU reset initiated
Info : J-Link ARM V7 compiled Feb 15 2011 11:03:33
Info : J-Link caps 0xb9ff7bbf
Info : J-Link hw version 70000
Info : J-Link hw type J-Link
Info : J-Link max mem block 9000
Info : J-Link configuration
Info : USB-Address: 0xff
Info : Kickstart power on JTAG-pin 19: 0xffffffff
Info : Vref = 3.196 TCK = 1 TDI = 0 TDO = 1 TMS = 0 SRST = 0 TRST = 0
Info : J-Link JTAG Interface ready
Info : clock speed 500 kHz
Info : JTAG tap: lm3s1968.cpu tap/device found: 0x3ba00477 (mfg: 0x23b, part: 0x
ba00, ver: 0x3)
Info : lm3s1968.cpu: hardware has 6 breakpoints, 4 watchpoints
--
Xiaofan
_______________________________________________
Openocd-development mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/openocd-development
