Signed-off-by: Luca Bruno <[email protected]>
---
src/jtag/drivers/buspirate.c | 18 +++++++++---------
1 files changed, 9 insertions(+), 9 deletions(-)
diff --git a/src/jtag/drivers/buspirate.c b/src/jtag/drivers/buspirate.c
index a360d23..62ab008 100644
--- a/src/jtag/drivers/buspirate.c
+++ b/src/jtag/drivers/buspirate.c
@@ -217,13 +217,13 @@ static int buspirate_execute_queue(void)
static int buspirate_init(void)
{
if (buspirate_port == NULL) {
- LOG_ERROR("You need to specify port !");
+ LOG_ERROR("You need to specify the serial port!");
return ERROR_JTAG_INIT_FAILED;
}
buspirate_fd = buspirate_serial_open(buspirate_port);
if (buspirate_fd == -1) {
- LOG_ERROR("Could not open serial port.");
+ LOG_ERROR("Could not open serial port");
return ERROR_JTAG_INIT_FAILED;
}
@@ -249,7 +249,7 @@ static int buspirate_init(void)
static int buspirate_quit(void)
{
- LOG_INFO("Shuting down buspirate ");
+ LOG_INFO("Shutting down buspirate.");
buspirate_jtag_set_mode(buspirate_fd, MODE_HIZ);
buspirate_jtag_set_speed(buspirate_fd, SERIAL_NORMAL);
@@ -665,7 +665,7 @@ static void buspirate_tap_append(int tms, int tdi)
tap_chain_index++;
} else
- LOG_ERROR("tap_chain overflow, Bad things will happen");
+ LOG_ERROR("tap_chain overflow, bad things will happen");
}
@@ -724,19 +724,19 @@ static void buspirate_jtag_enable(int fd)
while (!done) {
ret = buspirate_serial_read(fd, tmp, 4);
if (ret != 4) {
- LOG_ERROR("Buspirate error. Is is binary/"
+ LOG_ERROR("Buspirate error. Is binary"
"/OpenOCD support enabled?");
exit(-1);
}
if (strncmp(tmp, "BBIO", 4) == 0) {
ret = buspirate_serial_read(fd, tmp, 1);
if (ret != 1) {
- LOG_ERROR("Buspirate did not correctly! "
+ LOG_ERROR("Buspirate did not answer correctly! "
"Do you have correct firmware?");
exit(-1);
}
if (tmp[0] != '1') {
- LOG_ERROR("Unsupported binary protocol ");
+ LOG_ERROR("Unsupported binary protocol");
exit(-1);
}
if (cmd_sent == 0) {
@@ -747,7 +747,7 @@ static void buspirate_jtag_enable(int fd)
} else if (strncmp(tmp, "OCD1", 4) == 0)
done = 1;
else {
- LOG_ERROR("Buspirate did not correctly! "
+ LOG_ERROR("Buspirate did not answer correctly! "
"Do you have correct firmware?");
exit(-1);
}
@@ -794,7 +794,7 @@ static void buspirate_jtag_set_speed(int fd, char speed)
exit(-1);
}
if ((tmp[0] != CMD_UART_SPEED) || (tmp[1] != speed)) {
- LOG_ERROR("Buspirate didn't reply as expected");
+ LOG_ERROR("Buspirate did not reply as expected");
exit(-1);
}
LOG_INFO("Buspirate switched to %s mode",
--
1.7.5.4
_______________________________________________
Openocd-development mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/openocd-development
