> "Dennis Clarke" <[EMAIL PROTECTED]> wrote: > >> > Cdrecord does support DVD media since February 1998. >> >> Well DVD-R and DVD-RW yes. Totally. >> On media that is either 120mm or 80mm just fine. >> But not DVD+RW or DVD+R . > > Of course, DVD+ works. > > What is your problem?
Well, let us see. If I take a piece of DVD+RW 120mm media and perform a few inquiries I see this : [1] use the -atip option # /opt/csw/bin/cdrecord -v dev=0,0,0 -atip Cdrecord-ProDVD-Clone 2.01b38 (i386-pc-solaris2.8) Copyright (C) 1995-2004 Jörg Schilling Unlocked features: ProDVD Limited features: This copy of cdrecord is licensed for: Dennis_Clarke/[EMAIL PROTECTED]/for_blastwave_use TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Using libscg version 'schily-0.8'. SCSI buffer size: 57344 atapi: 0 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'PIONEER ' Identifikation : 'DVD-RW DVR-107D' Revision : '1.21' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: DVD+RW Profile: DVD+R Profile: DVD+RW (current) Profile: DVD-RW sequential overwrite Profile: DVD-RW restricted overwrite Profile: DVD-R sequential recording Profile: DVD-ROM Profile: CD-RW Profile: CD-R Profile: CD-ROM Using generic SCSI-3/mmc-3 DVD+RW driver (mmc_dvdplusrw). Driver flags : DVD MMC-3 SWABAUDIO BURNFREE Supported modes: PACKET SAO Drive buf size : 1605632 = 1568 KB Current Secsize: 2048 book type: DVD+RW, Version 2 (9.2) disc size: 120mm (0) minimum rate: Not specified (15) number of layers:0 track path: Parallel Track Path (0) layer type: illegal layer type (4) linear density: 0.267 µm/bit (0) track density: 0.74 µm/track (0) phys start: 196608 phys end: 2491711 end layer 0: 0 bca: 0 phys size:... 2295104 Manufacturer: 'RICOHJPN' Media type: 'W01' copyr prot type: 0 region mgt info: 0 cpm: 0 cgms: 0 [2] now try to blank that media # /opt/csw/bin/cdrecord -v dev=0,0,0 -blank=all Cdrecord-ProDVD-Clone 2.01b38 (i386-pc-solaris2.8) Copyright (C) 1995-2004 Jörg Schilling Unlocked features: ProDVD Limited features: This copy of cdrecord is licensed for: Dennis_Clarke/[EMAIL PROTECTED]/for_blastwave_use TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Using libscg version 'schily-0.8'. SCSI buffer size: 57344 atapi: 0 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'PIONEER ' Identifikation : 'DVD-RW DVR-107D' Revision : '1.21' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: DVD+RW Profile: DVD+R Profile: DVD+RW (current) Profile: DVD-RW sequential overwrite Profile: DVD-RW restricted overwrite Profile: DVD-R sequential recording Profile: DVD-ROM Profile: CD-RW Profile: CD-R Profile: CD-ROM Using generic SCSI-3/mmc-3 DVD+RW driver (mmc_dvdplusrw). Driver flags : DVD MMC-3 SWABAUDIO BURNFREE Supported modes: PACKET SAO Drive buf size : 1605632 = 1568 KB Current Secsize: 2048 Starting to write CD/DVD at speed 2 in real BLANK mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. /opt/csw/bin/cdrecord: Cannot blank with non Ricoh based drive. /opt/csw/bin/cdrecord: Cannot blank disk, aborting. # That fails because I don't have a drive made by Ricoh ? Strangely that DVD+RW media comes in a boldly logo'ed TDK case. Now I will grab a DVD+R media of the 120mm size. Normal stuff we see in stores all the time and I have a whole spindle here. [1] use the -atip option again # /opt/csw/bin/cdrecord -v dev=0,0,0 -atip Cdrecord-ProDVD-Clone 2.01b38 (i386-pc-solaris2.8) Copyright (C) 1995-2004 Jörg Schilling Unlocked features: ProDVD Limited features: This copy of cdrecord is licensed for: Dennis_Clarke/[EMAIL PROTECTED]/for_blastwave_use TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Using libscg version 'schily-0.8'. SCSI buffer size: 57344 atapi: 0 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'PIONEER ' Identifikation : 'DVD-RW DVR-107D' Revision : '1.21' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: DVD+R Profile: DVD+R (current) Profile: DVD+RW Profile: DVD-RW sequential overwrite Profile: DVD-RW restricted overwrite Profile: DVD-R sequential recording Profile: DVD-ROM Profile: CD-RW Profile: CD-R Profile: CD-ROM Using generic SCSI-3/mmc-3 DVD+R driver (mmc_dvdplusr). Driver flags : DVD MMC-3 SWABAUDIO BURNFREE Supported modes: PACKET SAO Drive buf size : 1605632 = 1568 KB Current Secsize: 2048 book type: DVD+R, Version 1 (10.1) disc size: 120mm (0) minimum rate: Not specified (15) number of layers:0 track path: Parallel Track Path (0) layer type: Rewritable Area (2) linear density: 0.267 µm/bit (0) track density: 0.74 µm/track (0) phys start: 196608 phys end: 2491711 end layer 0: 0 bca: 0 phys size:... 2295104 Manufacturer: 'RICOHJPN' Media type: 'R01' copyr prot type: 0 region mgt info: 0 [2] I see the "RICOHJPN" manufacturer above but I will try to blank this media anyways. # /bin/truss -faeilD -o /tmp/cdrecord.truss /opt/csw/bin/cdrecord -v dev=0,0,0 -blank=all Cdrecord-ProDVD-Clone 2.01b38 (i386-pc-solaris2.8) Copyright (C) 1995-2004 Jörg Schilling Unlocked features: ProDVD Limited features: This copy of cdrecord is licensed for: Dennis_Clarke/[EMAIL PROTECTED]/for_blastwave_use TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Using libscg version 'schily-0.8'. SCSI buffer size: 57344 atapi: 0 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'PIONEER ' Identifikation : 'DVD-RW DVR-107D' Revision : '1.21' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: DVD+R Profile: DVD+R (current) Profile: DVD+RW Profile: DVD-RW sequential overwrite Profile: DVD-RW restricted overwrite Profile: DVD-R sequential recording Profile: DVD-ROM Profile: CD-RW Profile: CD-R Profile: CD-ROM Using generic SCSI-3/mmc-3 DVD+R driver (mmc_dvdplusr). Driver flags : DVD MMC-3 SWABAUDIO BURNFREE Supported modes: PACKET SAO Drive buf size : 1605632 = 1568 KB Current Secsize: 2048 Starting to write CD/DVD at speed 4 in real BLANK mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. /opt/csw/bin/cdrecord: Cannot blank with non Ricoh based drive. /opt/csw/bin/cdrecord: Cannot blank disk, aborting. # http://www.blastwave.org/dclarke/cdrecord.truss.txt I should point out that this media says that its made by Maxell. Perhaps I should avoid tape companies because they are all actually made by Ricoh. Then again, are both these media that were bough two years apart actually made by Ricoh ? I don't know. I will try to burn to this DVD+R media in the same manner that I burn a DVD-R and I will use the Solaris Nevada snv_38 DVD image for x86. Thus : bash-3.00# ls /export/dvd/snv_38/ sol-nv-b38-x86-dvd.iso bash-3.00# gmd5sum /export/dvd/snv_38/sol-nv-b38-x86-dvd.iso 1e6f45f250efa8048056986099665586 /export/dvd/snv_38/sol-nv-b38-x86-dvd.iso Now I try to burn that : bash-3.00# /opt/csw/bin/cdrecord -v dev=0,0,0 -sao /export/dvd/snv_38/sol-nv-b38-x86-dvd.iso Cdrecord-ProDVD-Clone 2.01b38 (i386-pc-solaris2.8) Copyright (C) 1995-2004 Jörg Schilling Unlocked features: ProDVD Limited features: This copy of cdrecord is licensed for: Dennis_Clarke/[EMAIL PROTECTED]/for_blastwave_use TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Using libscg version 'schily-0.8'. SCSI buffer size: 57344 atapi: 0 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'PIONEER ' Identifikation : 'DVD-RW DVR-107D' Revision : '1.21' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: DVD+R Profile: DVD+R (current) Profile: DVD+RW Profile: DVD-RW sequential overwrite Profile: DVD-RW restricted overwrite Profile: DVD-R sequential recording Profile: DVD-ROM Profile: CD-RW Profile: CD-R Profile: CD-ROM Using generic SCSI-3/mmc-3 DVD+R driver (mmc_dvdplusr). Driver flags : DVD MMC-3 SWABAUDIO BURNFREE Supported modes: PACKET SAO Drive buf size : 1605632 = 1568 KB FIFO size : 33554432 = 32768 KB Track 01: data 2514 MB Total size: 2514 MB = 1287200 sectors Current Secsize: 2048 Blocks total: 2295104 Blocks current: 2295104 Blocks remaining: 1007904 Starting to write CD/DVD at speed 4 in real SAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. Starting new track at sector: 0 Track 01: 2514 of 2514 MB written (fifo 100%) [buf 73%] 4.3x. Track 01: Total bytes read/written: 2636185600/2636185600 (1287200 sectors). Writing time: 505.065s Average write speed 3.8x. Min drive buffer fill was 61% Fixating... Fixating time: 0.020s /opt/csw/bin/cdrecord: fifo had 45972 puts and 45972 gets. /opt/csw/bin/cdrecord: fifo was 0 times empty and 7490 times full, min fill was 96%. bash-3.00# Now lets try atip again : bash-3.00# /opt/csw/bin/cdrecord -v dev=0,0,0 -atip Cdrecord-ProDVD-Clone 2.01b38 (i386-pc-solaris2.8) Copyright (C) 1995-2004 Jörg Schilling Unlocked features: ProDVD Limited features: This copy of cdrecord is licensed for: Dennis_Clarke/[EMAIL PROTECTED]/for_blastwave_use TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Using libscg version 'schily-0.8'. SCSI buffer size: 57344 atapi: 0 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'PIONEER ' Identifikation : 'DVD-RW DVR-107D' Revision : '1.21' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: DVD+R Profile: DVD+R (current) Profile: DVD+RW Profile: DVD-RW sequential overwrite Profile: DVD-RW restricted overwrite Profile: DVD-R sequential recording Profile: DVD-ROM Profile: CD-RW Profile: CD-R Profile: CD-ROM Using generic SCSI-3/mmc-3 DVD+R driver (mmc_dvdplusr). Driver flags : DVD MMC-3 SWABAUDIO BURNFREE Supported modes: PACKET SAO Drive buf size : 1605632 = 1568 KB Current Secsize: 2048 book type: DVD+R, Version 1 (10.1) disc size: 120mm (0) minimum rate: Not specified (15) number of layers:0 track path: Parallel Track Path (0) layer type: Rewritable Area (2) linear density: 0.267 µm/bit (0) track density: 0.74 µm/track (0) phys start: 196608 phys end: 2491711 end layer 0: 0 bca: 0 phys size:... 2295104 Manufacturer: 'RICOHJPN' Media type: 'R01' copyr prot type: 0 region mgt info: 0 cpm: 0 cgms: 0 WARNING: Phys disk size 2295104 differs from rzone size 3582304! Prerecorded disk? WARNING: Phys start: 196608 Phys end 2491711 bash-3.00# and finally try to mount that thing : bash-3.00# mount -F hsfs -o ro /dev/dsk/c0t0d0s0 /cdrom mount: I/O error mount: cannot mount /dev/dsk/c0t0d0s0 Nothing I do here will improve matters much. I can try again with another DVD+R media but I get the same result. >> > Cdrecord allows you to reate dual/double-layer media in case that >> > don't care about the position of the layer break. >> >> Layer break ? Is that how dual layer works ? One needs to make two large >> ISO-9660 files and burn them or is there even a filesystem spec for the >> new >> blue laser larger capacity DVD media ? I would really like to burn some >> larger media formats. > > No, but for a DVD-Video, you need to have the layer break at the > right position between two "chapters". OH, I am only interested in DVD dual layer data or bootable disks. -- Dennis Clarke _______________________________________________ opensolaris-discuss mailing list [email protected]
