Thanks a lot Andreas ;-)
OK, so I would configure the br-ex as usually,
auto br-ex
iface br-ex inet static
address a.b.c.d
netmask 255.255.255.0
network a.b.c.0
dns-nameservers x.x.x.x
dns-search domin.xx
gateway a.b.c.1
but is it valid to configure the vlan bond0.45 like this, thus in promisc
mode ?
auto bond0.45
iface bond0.45 inet manual
up ifconfig $IFACE 0.0.0.0 up
up ip link set $IFACE promisc on
down ip link set $IFACE promisc off
down ifconfig $IFACE down
best regards
Yngvi
-----Original Message-----
From: Andreas Scheuring [mailto:[email protected]]
Sent: 16. júní 2015 07:47
To: Yngvi Páll Þorfinnsson
Cc: [email protected]
Subject: Re: [Openstack] network issue
Your setup should be fine.
Ensure, that you have created your openstack external network as flat provider
network (default with devstack). Then adding br-ex into the vlan device
enforces vlan traffic on the external network.
An alternative approach would be to add the bond interface into the br-ex
(instead of its vlan device) and create your openstack external provider
network as vlan network using vlan 45.
Both should work!
In general take be aware, all the vlans you're using have to be enabled in your
hardware switch as well if it's not a 20$ device.
Andreas
(IRC: scheuran)
On Mo, 2015-06-15 at 17:31 +0000, Yngvi Páll Þorfinnsson wrote:
> Hi
>
> We‘re using Ubuntu 14.04 on all servers. Using 1 controller node, 2
> network nodes, 4 compute nodes as well as 4 swift nodes.
>
>
>
> I‘ve been doing some changes on my network configuration and
> introducing vlans ( also bonding).
>
> My goal is to have all networks running on one 10G interface, as
> VLANs.
>
> I‘ve done this already for the management- and tunnel network.
>
> This is the setup:
>
>
>
> bond0.48 - mgmt interface
>
> bond0.47 – tunnel interface
>
>
>
> and then I would add this one as well
>
>
>
> bond0.45 – external interface
>
>
>
> and then add the bridge:
>
>
>
> # ovs-vsctl add-port br-ex
>
> # ovs-vsctl add-port br-ex bond0.45
>
>
>
> I could be wrong here, with the „bond0.45“ ...
>
> So does it make sense to go this path? Or more critical: is it
> possible to configure openstack like this?
>
>
>
> On the previous setup, I did configure the external br-ex like this:
>
>
>
> # ovs-vsctl add-port br-ex
>
> # ovs-vsctl add-port br-ex em3
>
>
>
> And defined be-ex and em3 in the interfaces file
>
> /etc/network/interfaces
>
> .
>
> .
>
> auto br-ex
>
> iface br-ex inet static
>
> address ip-number
>
> netmask 255.255.255.0
>
> network xxxx
>
> dns-nameservers yyyy
>
> dns-search siminn.is
>
> gateway zzzz
>
>
>
> auto em3
>
> iface em3 inet manual
>
> up ifconfig $IFACE 0.0.0.0 up
>
> up ip link set $IFACE promisc on
>
> down ip link set $IFACE promisc off
>
> down ifconfig $IFACE down
>
> .
>
>
>
>
>
> Could I achive this and configure the external network bridge, br-ex,
> as a vlan ?
>
>
>
> Best regards
>
> Yngvi
>
>
>
>
> _______________________________________________
> Mailing list: http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack
> Post to : [email protected]
> Unsubscribe :
> http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack
_______________________________________________
Mailing list: http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack
Post to : [email protected]
Unsubscribe : http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack
