Evgeniy L.
Thank you for the information. I have rebuilt the Fuel Community 11 server and left everything default with the exception of setting the PXE support to eth1. I am seeing the same issue. The Silicon Mechanics server with a Supermicro system board as been configured in every possible boot configuration that I can think of; and I’m still seeing the “PXE-E7B” error. I’m about to consign this server to another use. Regards, Ken Houle 469-634-4171 : <mailto:[email protected]> [email protected] From: Evgeniy L [mailto:[email protected]] Sent: Tuesday, October 31, 2017 9:58 AM To: Ken Houle <[email protected]> Cc: Openstack <[email protected]> Subject: Re: [Openstack] help - Fuel Community 11 - PXE I'm not sure if these options should be set, because they are required only if PXE server is on different host from DHCP server, which is not the case for Fuel. On Thu, Oct 26, 2017 at 8:25 AM, Ken Houle <[email protected] <mailto:[email protected]> > wrote: Evgeniy L: Thank you for the information. I have a few, possible silly/noob, question. After your email I reviewed the tcpdump again and identified that the “dhcp offer” does not contain options 66 and 67. You can see from the excerpt of a bootp capture the highlighted portions contain the IP address offered, next server, and boot file. However, in the options section there is not an option 66, tftp server name, and option 67, bootfile name. SO here is the question, taking cobbler into account which file should I be editing to attempt to add these options? Is the “/etc/cobbler/dhcp.template” file the correct file; thought “template” seems to indicate that it is not? If not, again silly/noob, which file should I be editing. Any assistance would be appreciated. Frame 4138: 342 bytes on wire (2736 bits), 342 bytes captured (2736 bits) Ethernet II, Src: Dell_b9:6a:02 (d4:ae:52:b9:6a:02), Dst: Broadcast (ff:ff:ff:ff:ff:ff) Internet Protocol Version 4, Src: 10.10.30.10, Dst: 255.255.255.255 User Datagram Protocol, Src Port: 67, Dst Port: 68 Bootstrap Protocol (Offer) Message type: Boot Reply (2) Hardware type: Ethernet (0x01) Hardware address length: 6 Hops: 0 Transaction ID: 0x906a77f9 Seconds elapsed: 18 Bootp flags: 0x8000, Broadcast flag (Broadcast) 1... .... .... .... = Broadcast flag: Broadcast .000 0000 0000 0000 = Reserved flags: 0x0000 Client IP address: 0.0.0.0 Your (client) IP address: 10.10.30.21 Next server IP address: 10.10.30.10 Relay agent IP address: 0.0.0.0 Client MAC address: SuperMic_6a:77:f9 (00:25:90:6a:77:f9) Client hardware address padding: 00000000000000000000 Server host name: boothost Boot file name: pxelinux.0 Magic cookie: DHCP Option: (53) DHCP Message Type (Offer) Option: (54) DHCP Server Identifier Option: (51) IP Address Lease Time Option: (58) Renewal Time Value Option: (59) Rebinding Time Value Option: (1) Subnet Mask Option: (28) Broadcast Address Option: (15) Domain Name Option: (6) Domain Name Server Option: (3) Router Option: (255) End Padding: 00 Regards, Ken Houle 469-634-4171 : <mailto:[email protected]> [email protected] From: Evgeniy L [mailto:[email protected] <mailto:[email protected]> ] Sent: Wednesday, October 25, 2017 11:45 AM To: Ken Houle <[email protected] <mailto:[email protected]> > Cc: Openstack <[email protected] <mailto:[email protected]> > Subject: Re: [Openstack] help - Fuel Community 11 - PXE Hi Ken, Fuel uses Cobbler which uses DNSMasq to provide DHCP and PXE boot, if the issue is hardware specific, you can try to search if anybody else had such problems with DNSMasq PXE boot and similar hardware. Thanks, On Wed, Oct 25, 2017 at 7:12 AM, Ken Houle <[email protected] <mailto:[email protected]> > wrote: All: First off not sure I am in the right place so if I am not please be kind and point me in the correct direction. I am attempting to build an Openstack system with Fuel Community 11 with a mix servers from different manufacturers. I have successfully installed Fuel Community 11 on the master node and am attempting to add nodes to the Openstack environment. The “Dell” servers pxe boot fine, see the master node and can be added to the system. However, I have an older “Silicon Mechanics” server that will not pxe boot. I have upgraded the AMI BIOS on the “Supermicro” system board to the latest release as well as the IPMI firmware. I have attempted to use both legacy and UEFI boot from the BIOS and I always see the same error. Please note that the Intel PXE release is 1.5.13. “PXE-E7B: Missing MTFTP server IP address. This message is displayed when the ROM did not receive any PXE discovery tags or proxyDHCP offers and the DHCP SIADDR field is set to 0.0.0.0.” I have take a tcpdump and see the dhcp discover and the dhcp offer. The Fuel master node is offering the server an IP address and is telling it what its next server and file are. Any assistance and or information would be greatly appreciated. Regards, <http://www.developingsolutions.com/> Ken Houle Sales Engineering <http://www.developingsolutions.com/> Developing Solutions, Inc. 469-634-4171 : <mailto:[email protected]> [email protected] _______________________________________________ Mailing list: http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack Post to : [email protected] <mailto:[email protected]> Unsubscribe : http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack
_______________________________________________ Mailing list: http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack Post to : [email protected] Unsubscribe : http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack
