Hi,
Le 06/02/2014 08:49, Josua Mayer a écrit : > Hi, > > I was trying something different to get the chromebook working: > I found in the Images.wiwi.in, that a lot of packages are marked as > PKG_BOOT_TAG and that way included in the initrd, suchas vboot, > gptfdisk,mrvl-firmware, which shouldnt be needed for booting imo. I reduced > those to just PKG_BOOT_TAG(u-boot-chromebook), PKG_BOOT_TAG(dtb-exynos5), No, it is there to be included in /boot partition. Marcus, am I right? But yes, we may remove vboot, etc. from PKG_BOOT_TAG. Dirk, Alex, are you OK with that? > which resulted in a smaller initrd that loaded without warnings. But then I > get just a black screen after the kernel is (hopefully) started. > In my opinion, this initrd is far too huge anyway, and I wonder why that is. Initrd is big for 1st boot because we need to repartition SD card and thus embed some tools in initrd. Then, initrd is regenerated and should not be too big anymore. Guillaume > > Josua Mayer > > Am 05.02.2014 20:46, schrieb [email protected]: >> Hi, >> >> >> ----- Daniel Bischof <[email protected]> a écrit : >>> Hi, >>> >>> are the latest Chromebook images supposed to work? I tried the most recent >>> Factory-ARM-XFCE-chromebook.armv7l-1.12.1-Build169.2 (of today) and got >> No. The problem is "ext2fs doesn't support tripple indirect blocks" which >> prevent to load all the initrd. >> >> I am working on upstream u-boot which could fix that. But it is not yet >> ready. :( >> >> >> Guillaume >> >> >>> ----- >>> ** File not found uEnv.txt >>> Loading file "boot.scr" from mmc device 1:2 (lxboot) >>> 2138 bytes read >>> Running bootscript ... >>> ## Executing script at 40007000 >>> mmc_init err 0, time 101923 >>> mmc0(part 0) is current deuice >>> Loading file "boot/linux.vmx" from mmc deuice 0:2 (KERN-A) >>> Failed to mount ext2 filesystem ... >>> ** Bad ext2 partition or disk — mmc 0:2 ** >>> mmc1 is current device >>> Loading file "boot/linux.vmx" from mmc device 1:2 (lxboot) >>> 3568304 bytes read >>> Loading file "boot/initrd.uboot" from mmc device 1:2 (lxboot) >>> ** ext2fs doesn't support tripple indirect blocks. ** >>> ** Unable to read "boot/initrd.uboot" from mmc 1:2 ** >>> Loading file "dtb/exynos5250—snow.dtb" from mmc device 1:2 (lxboot) >>> 34150 bytes read >>> ## Booting kernel from Legacy Image at 40007000 ... >>> Image Name: Linux—3.4.0—2—chromebook >>> Image Type: ARM Linux Kernel Image (uncompressed) >>> Data Size: 3568240 Bytes = 3.4 MiB >>> Load address: 40008000 >>> Entry Point: 40008000 >>> Verifying Checksum ... OK >>> ## Loading init Ramdisk from Legacy Image at 4f000000 ... >>> Image Name: Initrd >>> Image Type: ARM Linux RAMDisk Image (uncompressed) >>> Data Size: 156490936 Bytes = 149.2 MiB >>> Load Address: 00000000 >>> Entry Point: 00000000 >>> Verifying Checksum ... Bad Data CRC >>> Ramdisk image is corrupt or invalid >>> mmc0(part 0) is current device >>> ** Block device usb 0 not supported >>> mmc1 is current device >>> ** Block device usb 1 not supported >>> (Re)start USB... >>> USB: Register 1313 NbrPorts 3 >>> [USB] usb_lowlevel_init:852 0 >>> [USB] usb_lowlevel_init:852 1 >>> USB EHCI 1.00 >>> 1 USB Device(s) found >>> scanning bus for storage devices ... 0 Storage Device(s) found >>> Tring USB on device >>> ** Block device usb 0 not supported >>> ** Block device usb 0 not supported >>> SMDK5250 # >>> ----- >>> >>> on initial boot. Same result with most recent 13.1 images. >>> >>> >>> Best regards, >>> >>> --D.B. >>> -- >>> Daniel Bischof <[email protected]> > -- To unsubscribe, e-mail: [email protected] To contact the owner, e-mail: [email protected]
