On Sat, 1 Mar 2014 02:48:41 -0800 lists <[email protected]> wrote:
> On Sat, 01 Mar 2014 14:15:23 +0400 > "Matwey V. Kornilov" <[email protected]> wrote: > > > 01.03.2014 12:07, lists пишет: > > > > > > I can't seem to get it to work. I assume you have to SSH into it. > > > Nothing on the HDMI display. It doesn't show up in a nmap. > > > > > > > As any other JeOSes from Ports the image has interactive > > yast2-firstboot, you have to have serial console connection at the > > first boot, to set the root password, create the users, and > > configure the network. > > > > > > The Beaglebone Black doesn't have a real serial port. It requires a > special usb cable/chip. I'm trying not to be negative here, but I > think this won't be accepted well by the beaglebone users. I got the FTDI cable today. This is the text from the serial port when attempting to use opensuse JEOS: --------------------------------------------------------------------------------- \0x00 U-Boot SPL 2013.04-dirty (Jul 10 2013 - 14:02:53) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 mmc_send_cmd : timeout: No status update reading u-boot.img reading u-boot.img U-Boot 2013.04-dirty (Jul 10 2013 - 14:02:53) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1 \0x08\0x08\0x08 0 gpio: pin 53 (gpio 53) value is 1 mmc0 is current device micro SD card found mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 ** File not found uEnv.txt ** gpio: pin 55 (gpio 55) value is 1 ** File not found /boot/uImage ** U-Boot# --------------------------------------------------------------- -- To unsubscribe, e-mail: [email protected] To contact the owner, e-mail: [email protected]
