Le 21/06/2014 09:40, lists a écrit : > Boot issue? Well it doesn't. > > Here is the serial port output: > ------------------------------------ > \0x01\0x00 > U-Boot SPL 2013.04-dirty (Jul 10 2013 - 14:02:53) > musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, > SoftConn) musb-hdrc: MHDRC RTL version 2.0 > musb-hdrc: setup fifo_mode 4 > musb-hdrc: 28/31 max ep, 16384/16384 memory > USB Peripheral mode controller at 47401000 using PIO, IRQ 0 > musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, > SoftConn) musb-hdrc: MHDRC RTL version 2.0 > musb-hdrc: setup fifo_mode 4 > musb-hdrc: 28/31 max ep, 16384/16384 memory > USB Host mode controller at 47401800 using PIO, IRQ 0 > OMAP SD/MMC: 0 > mmc_send_cmd : timeout: No status update > reading u-boot.img > reading u-boot.img > > > U-Boot 2013.04-dirty (Jul 10 2013 - 14:02:53) > > I2C: ready > DRAM: 512 MiB > WARNING: Caches not enabled > NAND: No NAND device found!!! > 0 MiB > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > *** Warning - readenv() failed, using default environment > > musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, > SoftConn) musb-hdrc: MHDRC RTL version 2.0 > musb-hdrc: setup fifo_mode 4 > musb-hdrc: 28/31 max ep, 16384/16384 memory > USB Peripheral mode controller at 47401000 using PIO, IRQ 0 > musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, > SoftConn) musb-hdrc: MHDRC RTL version 2.0 > musb-hdrc: setup fifo_mode 4 > musb-hdrc: 28/31 max ep, 16384/16384 memory > USB Host mode controller at 47401800 using PIO, IRQ 0 > Net: <ethaddr> not set. Validating first E-fuse MAC > cpsw, usb_ether > Hit any key to stop autoboot: 1 \0x08\0x08\0x08 0 > gpio: pin 53 (gpio 53) value is 1 > mmc0 is current device > micro SD card found > mmc0 is current device > gpio: pin 54 (gpio 54) value is 1 > SD/MMC found on device 0 > Failed to mount ext2 filesystem... > ** Unrecognized filesystem type ** > gpio: pin 55 (gpio 55) value is 1 > ** No partition table - mmc 0 **
Is it a beaglebone or a beaglebone black board? Did you check the sh256sum of the compressed image (*.raw.xz file)? Is the SD card recognized on a desktop computer? Did you press the boot select switch button on power on as mentionned on this page: https://en.opensuse.org/HCL:BeagleBone_Black ? What returns the 'printenv' command in u-boot? Guillaume -- To unsubscribe, e-mail: [email protected] To contact the owner, e-mail: [email protected]
