You said that the system did not boot. So I checked. It boots for me. There is difference between the first and the sequential boots, so I checked that it was able to reboot successfully.
HDMI is not related here. 2014-10-18 20:51 GMT+04:00 <[email protected]>: > I wrote over the SDHC with a different disty, though I can load opensuse > again. But before I do that, I want to be clear what I'm supposed to document. > > First I presume this is just with the image, that is, don't upgrade. > > So the idea is if I boot twice, the HDMI returns? > > So the plan is to load the image, use the ncurses installer, and save > whatever is dumped via the serial port while it boots. Then do I use the > reboot command? Or do I hit the reset button. Assuming it boots, I then save > the serial port dump. > > Sorry for the top post, but I'm on a smartphone. > > Original Message > From: Matwey V. Kornilov > Sent: Saturday, October 18, 2014 2:53 AM > To: [email protected] > Subject: [opensuse-arm] Re: no HDMI on > openSUSE-13.1-ARM-JeOS-beaglebone.armv7l-1.12.1-Build38.9.raw.xz > > > Hi > > openSUSE-13.1-ARM-JeOS-beaglebone.armv7l-1.12.1-Build38.9.raw > > second-boots fine, just checked. Could you show full log of the first boot? > > > 14.10.2014 05:17, lists пишет: >> On Mon, 13 Oct 2014 01:19:16 -0700 >> lists <[email protected]> wrote: >> >>> The title says it all. No HDMI on this specific build. >>> openSUSE-13.1-ARM-JeOS-beaglebone.armv7l-1.12.1-Build38.9.raw.xz >>> >>> Otherwise, it boots/runs. I'm going to flog it a bit more. >> >> This image seems to have other problems. I used zypper update, then >> issued the reboot command. The display on the serial port got to >> "starting kernel" and just froze there. >> >> I did a reboot by hand (i.e. hold the boot button and apply power). >> --------------------------------------------- >> U-Boot 2013.04 (Mar 17 2014 - 15:34:07) >> >> I2C: ready >> DRAM: 512 MiB >> WARNING: Caches not enamusb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, >> HB-ISO Rx, HB-ISO Tx, SDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Host mode contnot set. Validating first E-fuse MAC >> cpsw, usb_ether >> Hit any key to stop autoboot: 0 >> mmc0 is current device >> SD/MMC found on device 0 >> 1950 bytes read in 6 ms (317.4 KiB/s) >> Running bootscript from mmc0 ... >> ## Executing script at 80200000 >> kerneladdr=0x802000004504224 bytes read in 609 ms (7.1 MiB/s) >> ** File not found initrd ** >> 21959 bytes read in 24 ms (892.6 KiB/s) >> ## Flattened Device Tree Tree in pla885c6 >> >> Starting kernel ... >> >> ------------------------------ >> Again, nothing happens. To be sure, I went to the HDMI port, just to >> see if the display got transferred there, and again, nothing. >> >> At this point, I'm going to halt testing and wait until someone thinks >> there is an image with HDMI support. >> > > > -- > To unsubscribe, e-mail: [email protected] > To contact the owner, e-mail: [email protected] > -- With best regards, Matwey V. Kornilov http://blog.matwey.name xmpp://[email protected] -- To unsubscribe, e-mail: [email protected] To contact the owner, e-mail: [email protected]
