Hello community, here is the log from the commit of package DisplayCAL for openSUSE:Factory checked in at 2019-11-08 15:28:32 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Comparing /work/SRC/openSUSE:Factory/DisplayCAL (Old) and /work/SRC/openSUSE:Factory/.DisplayCAL.new.2990 (New) ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Package is "DisplayCAL" Fri Nov 8 15:28:32 2019 rev:36 rq:746576 version:3.8.8.1 Changes: -------- --- /work/SRC/openSUSE:Factory/DisplayCAL/DisplayCAL.changes 2019-10-07 14:14:03.574899115 +0200 +++ /work/SRC/openSUSE:Factory/.DisplayCAL.new.2990/DisplayCAL.changes 2019-11-08 15:28:35.671183269 +0100 @@ -1,0 +2,53 @@ +Thu Nov 07 21:18:10 UTC 2019 - [email protected] + +- Update to 3.8.8.1: + * [Moderate] Work-around failure to launch if wxPython 3.0 / + wxWidgets 3.0 release number do not match (using wxPython 3.0 + is deprecated). + +------------------------------------------------------------------- +Wed Nov 06 23:13:10 UTC 2019 - [email protected] + +- Update to 3.8.8: + * [Enhancement] Detect and warn about malformed colorimeter + corrections (e.g. from non-official sources). Move them to the + trash automatically if they were previously (manually) + installed. + * [Enhancement] Always enumerate instruments on application + startup if more than one instrument was detected the last time + the application was used (cross-platform consistency). + * [Enhancement] When prompting for instrument calibration, + display the just now detected instrument name instead of the + previously enumerated name (the latter might be stale if you + forgot to refresh after changing connected instruments). + * [Enhancement] Use a slightly improved smoothing method when + creating high resolution PCS to device tables. + * [Enhancement] Increase automatic PCS to device table resolution + for L*a*b* LUT profiles to 45x45x45 if using smoothing. + * [Enhancement] [UI] Only auto-close profile/3D LUT installation + dialog after a successful installation. + * [Enhancement] Don't auto-close madTPG after 3D LUT + installation. + * [Minor] madVR 3D LUT generation: Always write D65 white to 3D + LUT input primaries metadata so madVR does not attempt to + correct whitepoint differences on its own when using a custom + whitepoint (the 3D LUT itself will map the custom whitepoint + correctly). + * [Minor] madVR 3D LUT installation: Don't attempt to install 3D + LUTs with unsupported input primaries metadata (i.e. not Rec. + 709, SMPTE C, EBU/PAL, Rec. 2020 or DCI P3) as madVR will + overwrite the metadata depending on the 3D LUT install slot. + Such 3D LUTs should only be assigned manually in madVR instead. + * [Trivial] [UI] When loading settings, always enable the 3D LUT + tab if the display is virtual (consistent with display + selection behavior). + * [Trivial] Also apply black point correction when creating a + matrix profile without black point compensation (consistency). + * [Trivial] Do not create swapped matrix fallback tags for XYZ + LUT profiles when using the alternate forward profiler and the + used ArgyllCMS version is >= 2.1 (be consistent with + ArgyllCMS). + * [Trivial] madVR 3D LUT generation: Accept negative values for + input primaries metadata. + +------------------------------------------------------------------- Old: ---- DisplayCAL-3.8.7.1.tar.gz New: ---- DisplayCAL-3.8.8.1.tar.gz ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Other differences: ------------------ ++++++ DisplayCAL.spec ++++++ --- /var/tmp/diff_new_pack.DBEiKh/_old 2019-11-08 15:28:37.707185559 +0100 +++ /var/tmp/diff_new_pack.DBEiKh/_new 2019-11-08 15:28:37.711185563 +0100 @@ -30,7 +30,7 @@ License: GPL-3.0+ Group: Productivity/Graphics/Other Name: DisplayCAL -Version: 3.8.7.1 +Version: 3.8.8.1 Release: 0 Source0: http://displaycal.net/download/%{name}-%version.tar.gz Url: https://displaycal.net/ ++++++ DisplayCAL-3.8.7.1.tar.gz -> DisplayCAL-3.8.8.1.tar.gz ++++++ /work/SRC/openSUSE:Factory/DisplayCAL/DisplayCAL-3.8.7.1.tar.gz /work/SRC/openSUSE:Factory/.DisplayCAL.new.2990/DisplayCAL-3.8.8.1.tar.gz differ: char 5, line 1
