-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Richard Pace wrote: > I've reported this to Novell, bug report 231118, and also posted to KDE-Linux > list with no response from KDE-Linux, and it doesn't appear > that anyone at Novell has any reply yet to the problem report. I thought I'd > check here if anyone has > experienced this problem. I've installed SuSE 10.2 on a new HP Pavilion with > AMD Athlon 64 X2 Dual. > I had to use boot option ACPI=off in order to install. Otherwise, the boot > hangs at "Starting udev...". > After installation of 10.2, I still have to use ACPI=off (does not power off > at shutdown either, > but that's another problem). > > Now for the problem. External USB drive is not recogized when plugged into > USB 2.0 port. > External drive has its own power supply. Also, USB memory stick is not > recognized when plugged into USB port. > I know the ports work, since I have Windows XP installed as dual boot, and > Windows XP has no problem recongizing the devices. > > There is no /proc/bus/usb defined. > > lsusb shows no devices. lsmod shows usbcore installed along with ohci_hcd > and ehci_hcd. > > I have attached my startup log which shows some errors with ohci_hcd and > ehci_hcd drivers. I'm convinced these errors are at the cord of > the problem. And from what I've, perhaps it is related to the fact that I > can't boot with ACPI - I'm not an expert in kernel stuff and > drivers, though. > Specifically, these lines appears in the log: > > <6>usbcore: registered new driver usbfs > <6>usbcore: registered new driver hub > .... > <7>PCI: Setting latency timer of device 0000:00:10.1 to 64 > <7>ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) > .... > <4>PCI: No IRQ known for interrupt pin A of device 0000:00:0b.0. Probably > buggy MP table. > <3>ohci_hcd 0000:00:0b.0: Found HC with no IRQ. Check BIOS/PCI 0000:00:0b.0 > setup! > <3>ohci_hcd 0000:00:0b.0: init 0000:00:0b.0 fail, -19 > <4>PCI: No IRQ known for interrupt pin B of device 0000:00:0b.1. Probably > buggy MP table. > <3>ehci_hcd 0000:00:0b.1: Found HC with no IRQ. Check BIOS/PCI 0000:00:0b.1 > setup! > <3>ehci_hcd 0000:00:0b.1: init 0000:00:0b.1 fail, -19 > > There aren't any BIOS settings that will affect IRQs. It's an ASUS A8N-BR > motherboard with Phoenix Bios from Sept 2006 (i.e. it's current). > There is a USB Legacy Bios setting which is set to "AUTO". I've tried that > with "DISABLE" and "ENABLE" with no effect. > > I've tried several other boot options in different combinations with no > effect: acpi_user_timer_override nomsi pci=routeirq acpi=oldboot noapic > When I use "noapic", boot messages suggest using "pci=biosirq". However when > I tried using "pci=biosirq", I get "biosirq unknown kernel option" > or something like that. > > Any suggestions and/or comments appreciated. > > Regards, > Richard > > > ------------------------------------------------------------------------ > > Inspecting /boot/System.map-2.6.18.2-34-default > Loaded 23895 symbols from /boot/System.map-2.6.18.2-34-default. > Symbols match kernel version 2.6.18. > No module symbols loaded - kernel modules not enabled. > > klogd 1.4.1, log source = ksyslog started. > <4>Bootdata ok (command line is root=/dev/sda6 vga=0x317 resume=/dev/sda5 > splash=silent acpi=off) > <5>Linux version 2.6.18.2-34-default ([EMAIL PROTECTED]) (gcc version 4.1.2 > 20061115 (prerelease) (SUSE Linux)) #1 SMP Mon Nov 27 11:46:27 UTC 2006 > <6>BIOS-provided physical RAM map: > <4> BIOS-e820: 0000000000000000 - 000000000009f000 (usable) > <4> BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) > <4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > <4> BIOS-e820: 0000000000100000 - 000000007bef0000 (usable) > <4> BIOS-e820: 000000007bef0000 - 000000007bef3000 (ACPI NVS) > <4> BIOS-e820: 000000007bef3000 - 000000007bf00000 (ACPI data) > <4> BIOS-e820: 000000007c000000 - 0000000080000000 (reserved) > <4> BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) > <4> BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) > <6>DMI present. > <6>Scanning NUMA topology in Northbridge 24 > <6>Number of nodes 1 > <6>Node 0 MemBase 0000000000000000 Limit 000000007bef0000 > <7>NUMA: Using 63 for the hash shift. > <6>Using node hash shift of 63 > <6>Bootmem setup node 0 0000000000000000-000000007bef0000 > <7>On node 0 totalpages: 499545 > <7> DMA zone: 2893 pages, LIFO batch:0 > <7> DMA32 zone: 496652 pages, LIFO batch:31 > <6>Nvidia board detected. Ignoring ACPI timer override. > <6>If you got timer trouble try acpi_use_timer_override > <4>Intel MultiProcessor Specification v1.4 > <6> Virtual Wire compatibility mode. > <6>OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000 > <6>Processor #0 15:11 APIC version 17 > <6>Processor #1 15:11 APIC version 17 > <4>I/O APIC #2 Version 17 at 0xFEC00000. > <6>Setting APIC routing to physical flat > <6>Processors: 2 > <6>Allocating PCI resources starting at 88000000 (gap: 80000000:70000000) > <6>SMP: Allowing 2 CPUs, 0 hotplug CPUs > <4>Built 1 zonelists. Total pages: 499545 > <5>Kernel command line: root=/dev/sda6 vga=0x317 resume=/dev/sda5 > splash=silent acpi=off > <6>bootsplash: silent mode. > <4>Initializing CPU#0 > <4>PID hash table entries: 4096 (order: 12, 32768 bytes) > <6>time.c: Using 1.193182 MHz WALL PIT GTOD PIT/TSC timer. > <6>time.c: Detected 2004.214 MHz processor. > <4>Console: colour dummy device 80x25 > <4>Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) > <4>Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) > <4>Checking aperture... > <4>CPU 0: aperture @ 7e000000 size 32 MB > <4>Aperture too small (32 MB) > <4>No AGP bridge found > <4>Memory: 1991528k/2030528k available (1915k kernel code, 38612k reserved, > 1278k data, 188k init) > <4>Calibrating delay using timer specific routine.. 4014.40 BogoMIPS > (lpj=8028815) > <6>Security Framework v1.0.0 initialized > <4>Mount-cache hash table entries: 256 > <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) > <6>CPU: L2 Cache: 512K (64 bytes/line) > <6>CPU 0/0 -> Node 0 > <6>CPU: Physical Processor ID: 0 > <6>CPU: Processor Core ID: 0 > <6>SMP alternatives: switching to UP code > <6>checking if image is initramfs... it is > <6>Freeing initrd memory: 3392k freed > <4>ExtINT not setup in hardware but reported by MP table > <6>Using IO-APIC 2 > <6>Using local APIC timer interrupts. > <4>result 12526353 > <6>Detected 12.526 MHz APIC timer. > <6>SMP alternatives: switching to SMP code > <6>Booting processor 1/2 APIC 0x1 > <4>Initializing CPU#1 > <4>Calibrating delay using timer specific routine.. 4008.63 BogoMIPS > (lpj=8017269) > <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) > <6>CPU: L2 Cache: 512K (64 bytes/line) > <6>CPU 1/1 -> Node 0 > <6>CPU: Physical Processor ID: 0 > <6>CPU: Processor Core ID: 1 > <4>AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02 > <6>CPU 1: Syncing TSC to CPU 0. > <6>CPU 1: synchronized TSC with CPU 0 (last diff 21 cycles, maxerr 485 cycles) > <6>Brought up 2 CPUs > <6>testing NMI watchdog ... OK. > <4>migration_cost=285 > <6>NET: Registered protocol family 16 > <6>PCI: Using configuration type 1 > <6>ACPI: Interpreter disabled. > <4>PCI: Probing PCI hardware > <7>PCI: Probing PCI hardware (bus 00) > <7>Boot video device is 0000:00:05.0 > <6>PCI: Transparent bridge - 0000:00:10.0 > <6>PCI->APIC IRQ transform: 0000:00:05.0[A] -> IRQ 5 > <6>PCI->APIC IRQ transform: 0000:00:0e.0[A] -> IRQ 10 > <6>PCI->APIC IRQ transform: 0000:00:0f.0[A] -> IRQ 11 > <6>PCI->APIC IRQ transform: 0000:00:10.1[B] -> IRQ 7 > <6>PCI->APIC IRQ transform: 0000:00:14.0[A] -> IRQ 11 > <4>PCI: using PPB 0000:00:10.0[B] to get irq 7 > <6>PCI->APIC IRQ transform: 0000:02:05.0[B] -> IRQ 7 > <4>PCI: using PPB 0000:00:10.0[B] to get irq 7 > <6>PCI->APIC IRQ transform: 0000:02:09.0[B] -> IRQ 7 > <6>PCI-DMA: Disabling IOMMU. > <6>PCI: Bridge: 0000:00:04.0 > <6> IO window: a000-afff > <6> MEM window: fdd00000-fddfffff > <6> PREFETCH window: fde00000-fdefffff > <6>PCI: Bridge: 0000:00:10.0 > <6> IO window: b000-bfff > <6> MEM window: fdc00000-fdcfffff > <6> PREFETCH window: f4000000-f7ffffff > <7>PCI: Setting latency timer of device 0000:00:04.0 to 64 > <7>PCI: Setting latency timer of device 0000:00:10.0 to 64 > <6>NET: Registered protocol family 2 > <4>IP route cache hash table entries: 65536 (order: 7, 524288 bytes) > <4>TCP established hash table entries: 262144 (order: 10, 4194304 bytes) > <4>TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) > <6>TCP: Hash tables configured (established 262144 bind 65536) > <6>TCP reno registered > <6>audit: initializing netlink socket (disabled) > <5>audit(1167334419.416:1): initialized > <4>Total HugeTLB memory allocated, 0 > <5>VFS: Disk quotas dquot_6.5.1 > <4>Dquot-cache hash table entries: 512 (order 0, 4096 bytes) > <6>Initializing Cryptographic API > <6>io scheduler noop registered > <6>io scheduler anticipatory registered > <6>io scheduler deadline registered > <6>io scheduler cfq registered (default) > <7>PCI: Setting latency timer of device 0000:00:04.0 to 64 > <4>pcie_portdrv_probe->Dev[02fb:10de] has invalid IRQ. Check vendor BIOS > <4>assign_interrupt_mode Found MSI capability > <7>Allocate Port Service[0000:00:04.0:pcie00] > <6>vesafb: framebuffer at 0xe0000000, mapped to 0xffffc20000080000, using > 6144k, total 65536k > <6>vesafb: mode is 1024x768x16, linelength=2048, pages=1 > <6>vesafb: scrolling: redraw > <6>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 > <6>bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size > 81749 bytes,<6>...found (1024x768, 46202 bytes, v3). > <4>Console: switching to colour frame buffer device 124x44 > <6>fb0: VESA VGA frame buffer device > <6>Real Time Clock Driver v1.12ac > <6>Non-volatile memory driver v1.2 > <6>Linux agpgart interface v0.101 (c) Dave Jones > <6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled > <4>RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize > <6>serio: i8042 AUX port at 0x60,0x64 irq 12 > <6>serio: i8042 KBD port at 0x60,0x64 irq 1 > <6>mice: PS/2 mouse device common for all mice > <6>input: PC Speaker as /class/input/input0 > <6>input: AT Translated Set 2 keyboard as /class/input/input1 > <6>md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 > <6>md: bitmap version 4.39 > <6>NET: Registered protocol family 1 > <6>Freeing unused kernel memory: 188k freed > <4>logips2pp: Detected unknown logitech mouse model 0 > <6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > <6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > <5>SCSI subsystem initialized > <6>NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0 > <6>NFORCE-MCP51: chipset revision 161 > <6>NFORCE-MCP51: not 100% native mode: will probe irqs later > <6>NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller > <6> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA > <7>Probing IDE interface ide0... > <6>input: ImPS/2 Logitech Wheel Mouse as /class/input/input2 > <4>hda: HL-DT-STDVDRRW GSA-H20L, ATAPI CD/DVD-ROM drive > <4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > <7>libata version 2.00 loaded. > <7>sata_nv 0000:00:0e.0: version 2.0 > <7>PCI: Setting latency timer of device 0000:00:0e.0 to 64 > <6>ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xDC00 irq 10 > <6>ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xDC08 irq 10 > <6>scsi0 : sata_nv > <6>ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) > <6>ata1.00: ATA-7, max UDMA/100, 390721968 sectors: LBA48 NCQ (depth 0/32) > <6>ata1.00: ata1: dev 0 multi count 1 > <6>ata1.00: configured for UDMA/100 > <6>scsi1 : sata_nv > <6>ata2: SATA link down (SStatus 0 SControl 310) > <4>ATA: abnormal status 0x7F on port 0x977 > <5> Vendor: ATA Model: ST3200827AS Rev: 3.AH > <5> Type: Direct-Access ANSI SCSI revision: 05 > <5>SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) > <5>sda: Write Protect is off > <7>sda: Mode Sense: 00 3a 00 00 > <5>SCSI device sda: drive cache: write back > <5>SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) > <5>sda: Write Protect is off > <7>sda: Mode Sense: 00 3a 00 00 > <5>SCSI device sda: drive cache: write back > <6> sda: sda1 sda2 < sda5 sda6 sda7 > > <5>sd 0:0:0:0: Attached scsi disk sda > <7>PCI: Setting latency timer of device 0000:00:0f.0 to 64 > <6>ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC800 irq 11 > <6>ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC808 irq 11 > <6>scsi2 : sata_nv > <5>sd 0:0:0:0: Attached scsi generic sg0 type 0 > <6>ata3: SATA link down (SStatus 0 SControl 310) > <4>ATA: abnormal status 0x7F on port 0x9E7 > <6>scsi3 : sata_nv > <6>ata4: SATA link down (SStatus 0 SControl 310) > <4>ATA: abnormal status 0x7F on port 0x967 > <6>BIOS EDD facility v0.16 2004-Jun-25, 2 devices found > <4>Attempting manual resume > <6>kjournald starting. Commit interval 5 seconds > <7>Losing some ticks... checking if CPU frequency changed. > <6>EXT3 FS on sda6, internal journal > <6>EXT3-fs: mounted filesystem with ordered data mode. > <6>forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56. > <7>PCI: Setting latency timer of device 0000:00:14.0 to 64 > <6>forcedeth: using HIGHDMA > <6>usbcore: registered new driver usbfs > <6>usbcore: registered new driver hub > <6>eth0: forcedeth.c: subsystem: 0103c:2a41 bound to 0000:00:14.0 > <7>PCI: Setting latency timer of device 0000:00:10.1 to 64 > <7>ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) > <6>Linux video capture interface: v2.00 > <7>ieee1394: Initialized config rom entry `ip1394' > <6>hda: ATAPI 63X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) > <6>Uniform CD-ROM driver Revision: 3.20 > <6>ivtv: ==================== START INIT IVTV ==================== > <6>ivtv: version 0.8.0 (tagged release) loading > <6>ivtv: Linux version: 2.6.18.2-34-default SMP mod_unload gcc-4.1 > <6>ivtv: In case of problems please include the debug info between > <6>ivtv: the START INIT IVTV and END INIT IVTV lines, along with > <6>ivtv: any module options, when mailing the ivtv-users mailinglist. > <6>hda_codec: Unknown model for ALC883, trying auto-probe from BIOS... > <7>ALSA sound/pci/hda/hda_codec.c:2117: autoconfig: line_outs=4 > (0x14/0x17/0x16/0x15/0x0) > <7>ALSA sound/pci/hda/hda_codec.c:2121: speaker_outs=0 > (0x0/0x0/0x0/0x0/0x0) > <7>ALSA sound/pci/hda/hda_codec.c:2123: hp=0x1b, dig_out=0x1e, din_in=0x0 > <7>ALSA sound/pci/hda/hda_codec.c:2131: inputs: mic=0x18, fmic=0x0, > line=0x1a, fline=0x0, cd=0x0, aux=0x0 > <6>i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00 > <6>i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40 > <4>PCI: No IRQ known for interrupt pin A of device 0000:00:0b.0. Probably > buggy MP table. > <3>ohci_hcd 0000:00:0b.0: Found HC with no IRQ. Check BIOS/PCI 0000:00:0b.0 > setup! > <3>ohci_hcd 0000:00:0b.0: init 0000:00:0b.0 fail, -19 > <4>PCI: No IRQ known for interrupt pin B of device 0000:00:0b.1. Probably > buggy MP table. > <3>ehci_hcd 0000:00:0b.1: Found HC with no IRQ. Check BIOS/PCI 0000:00:0b.1 > setup! > <3>ehci_hcd 0000:00:0b.1: init 0000:00:0b.1 fail, -19 > <6>ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[7] MMIO=[fdcff000-fdcff7ff] > Max Packet=[1024] IR/IT contexts=[8/8] > <6>ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) > <6>ivtv0: Unreasonably low latency timer, setting to 64 (was 32) > <6>ivtv0: unable to open firmware v4l-cx2341x-enc.fw > <6>ivtv0: did you put the firmware in the hotplug firmware directory? > <6>ivtv0 warning: failed loading encoder firmware > <6>ivtv0 warning: Error loading firmware -3! > <3>ivtv0: Error -3 initializing firmware. > <3>Trying to free already-free IRQ 7 > <3>ivtv0: Error -12 on initialization > <4>ivtv: probe of 0000:02:09.0 failed with error -12 > <6>ivtv: ==================== END INIT IVTV ==================== > <6>ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based) > <7>ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000ed3868] > <6>ivtv0: unable to open firmware v4l-cx2341x-enc.fw > <6>ivtv0: did you put the firmware in the hotplug firmware directory? > <6>ivtv0 warning: failed loading encoder firmware > <6>ivtv0 warning: Error loading firmware -3! > <3>ivtv0: Error -3 initializing firmware. > <3>Trying to free already-free IRQ 7 > <3>ivtv0: Error -12 on initialization > <4>ivtv: probe of 0000:02:09.0 failed with error -12 > <6>Adding 2104472k swap on /dev/sda5. Priority:-1 extents:1 across:2104472k > <6>device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [EMAIL > PROTECTED] > <6>loop: loaded (max 8 devices) > <6>kjournald starting. Commit interval 5 seconds > <6>EXT3 FS on sda7, internal journal > <6>EXT3-fs: mounted filesystem with ordered data mode. > <6>NTFS driver 2.1.27 [Flags: R/W MODULE]. > <6>NTFS volume version 3.1. > <6>AppArmor: AppArmor initialized > <5>audit(1167334432.636:2): AppArmor initialized > <4> > Kernel logging (ksyslog) stopped. > Kernel log daemon terminating. > > Boot logging started on /dev/tty1(/dev/console) at Thu Dec 28 19:33:39 2006 > > Trying manual resume from /dev/sda5 > Creating device nodes with udev > Loading ide-core > Loading ide-disk > Loading scsi_mod > Loading sd_mod > Loading amd74xx > Loading libata > Loading sata_nv > Loading processor > Loading thermal > FATAL: Error inserting thermal > (/lib/modules/2.6.18.2-34-default/kernel/drivers/acpi/thermal.ko): No such > device > Loading fan > FATAL: Error inserting fan > (/lib/modules/2.6.18.2-34-default/kernel/drivers/acpi/fan.ko): No such device > Loading edd > Loading jbd > Loading mbcache > Loading ext3 > Invoking userspace resume from /dev/sda5 > resume: Could not stat configuration file > resume: libgcrypt version: 1.2.3 > resume: Could not read the image > Invoking in-kernel resume from /dev/sda5 > Waiting for device /dev/sda6 to appear: ok > fsck 1.39 (29-May-2006) > [/bin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/sda6 > /dev/sda6: Superblock last write time is in the future. FIXED. > /dev/sda6: clean, 239950/2626560 files, 1402147/5242880 blocks > fsck succeeded. Mounting root device read-write. > Mounting root /dev/sda6 > > Boot logging started on /dev/tty1(/dev/console (deleted)) at Thu Dec 28 > 11:33:44 2006 > > <notice>boot.udev start > Starting udevd done > <notice>'boot.udev start' exits with status 0 > <notice>boot.rootfsck start > Activating swap-devices in /etc/fstab... > done<notice>'boot.rootfsck start' exits with status 0 > <notice>boot.loadmodules start > Loading required kernel modules > done<notice>'boot.loadmodules start' exits with status 0 > <notice>boot.preload_early start > done > <notice>'boot.preload_early start' exits with status 0 > <notice>boot.scpm start > <notice>'boot.scpm start' exits with status 0 > <notice>boot.device-mapper start > Activating device mapper... > done > <notice>'boot.device-mapper start' exits with status 0 > <notice>boot.md start > Starting MD Raid done > <notice>'boot.md start' exits with status 0 > <notice>boot.lvm start > Waiting for udev to settle... > Scanning for LVM volume groups... > Reading all physical volumes. This may take a while... > No volume groups found > No volume groups found > Activating LVM volume groups... > No volume groups found > done > <notice>'boot.lvm start' exits with status 0 > <notice>boot.localfs start > Checking file systems... > fsck 1.39 (29-May-2006) > /dev/sda7: Superblock last write time is in the future. FIXED. > /dev/sda7: clean, 611/12713984 files, 447684/25400765 blocks > donedone > Mounting local file systems... > proc on /proc type proc (rw) > sysfs on /sys type sysfs (rw) > debugfs on /sys/kernel/debug type debugfs (rw) > udev on /dev type tmpfs (rw) > devpts on /dev/pts type devpts (rw,mode=0620,gid=5) > /dev/sda7 on /home type ext3 (rw,acl,user_xattr) > /dev/sda1 on /windows/C type ntfs > (ro,noexec,nosuid,nodev,gid=100,umask=0002,nls=utf8) > done<notice>'boot.localfs start' exits with status 0 > <notice>boot.apparmor start > Loading AppArmor module done > Mounting securityfs on /sys/kernel/security done > Loading AppArmor profiles done > <notice>'boot.apparmor start' exits with status 0 > <notice>boot.cleanup start > <notice>'boot.cleanup start' exits with status 0 > <notice>boot.clock start > Setting up the hardware clockdone > <notice>'boot.clock start' exits with status 0 > <notice>boot.cycle start > <notice>'boot.cycle start' exits with status 6 > <notice>boot.klog start > Creating /var/log/boot.msg > done<notice>killproc: kill(856,29) > <notice>'boot.klog start' exits with status 0 > <notice>boot.proc start > <notice>'boot.proc start' exits with status 0 > <notice>boot.sysctl start > Setting current sysctl status from /etc/sysctl.conf > net.ipv4.icmp_echo_ignore_broadcasts = 1 > net.ipv4.conf.all.rp_filter = 1 > done > <notice>'boot.sysctl start' exits with status 0 > <notice>boot.udev_retry start > Retry device configurationdone > <notice>'boot.udev_retry start' exits with status 0 > <notice>boot.videobios start > <notice>'boot.videobios start' exits with status 0 > <notice>boot.crypto start > <notice>'boot.crypto start' exits with status 0 > <notice>boot.ipconfig start > Enabling syn flood protectiondone > Disabling IP forwardingdone > done > <notice>'boot.ipconfig start' exits with status 0 > <notice>boot.localnet start > Setting up hostname 'linux'done > Setting up loopback interface lo > lo IP address: 127.0.0.1/8 > done > <notice>'boot.localnet start' exits with status 0 > <notice>boot.preload start > done > <notice>'boot.preload start' exits with status 0 > <notice>boot.swap start > Activating remaining swap-devices in /etc/fstab... > done<notice>'boot.swap start' exits with status 0 > <notice>SuSEfirewall2_init start > Starting Firewall Initialization (phase 1 of 2) SuSEfirewall2: Warning: > ip6tables does not support state matching. Extended IPv6 support disabled. > done > <notice>'SuSEfirewall2_init start' exits with status 0 > <notice>boot.ldconfig start > <notice>'boot.ldconfig start' exits with status 0 > System Boot Control: The system has been set up > Skipped features: boot.cycle > System Boot Control: Running /etc/init.d/boot.local > done<notice>killproc: kill(856,3) > > INIT: Entering runlevel: 5 > > > > Boot logging started on /dev/tty1(/dev/console) at Thu Dec 28 19:34:07 2006 > > <notice>Master Resource Control: previous runlevel: N, switching to runlevel: > 5 > Loading AppArmor profiles - AppArmor already loaded with profiles.skipped > acpid: no ACPI support in kernelskipped > startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng ], [ > CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh > ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 > COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PWD=/ > PREVLEVEL=N LINES=44 acpi=off SHLVL=2 HOME=/ SPLASH=yes splash=silent > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/sbin/syslog-ng ] > done > Initializing random number generatordone > <notice>startproc: execve (/usr/bin/dbus-daemon) [ /usr/bin/dbus-daemon > --system ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh > TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 > REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 > RUNLEVEL=5 PWD=/ > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg > PREVLEVEL=N acpi=off LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/usr/bin/dbus-daemon ] > <notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x -x ], [ > CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh > ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 > COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PWD=/ > PREVLEVEL=N LINES=44 acpi=off SHLVL=2 HOME=/ SPLASH=yes splash=silent > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/sbin/klogd ] > <notice>startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ > CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux > ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 > COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg > PREVLEVEL=N acpi=off LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/sbin/resmgrd ] > Starting syslog servicesdone > Starting D-Bus daemondone > Starting resource managerdone > Starting irqbalance unused > <notice>startproc: execve (/usr/sbin/polkitd) [ /usr/sbin/polkitd ], [ > CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux > ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 > COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg > PREVLEVEL=N acpi=off LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/usr/sbin/polkitd ] > Starting PolicyKit daemondone > <notice>startproc: execve (/usr/sbin/hald) [ /usr/sbin/hald --daemon=yes ], [ > CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux > ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 > COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg > PREVLEVEL=N acpi=off LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/usr/sbin/hald ] > Starting HAL daemondone > Loading CPUFreq modules (CPUFreq not supported) > Loading keymap i386/qwerty/us.map.gz > doneLoading compose table winkeys shiftctrl latin1.adddone > Start Unicode mode > doneLoading console font lat9w-16.psfu -m trivial G0:loadable > done<notice>pidofproc: dhcpcd 3066 > Setting up network interfaces: > lo > lo IP address: 127.0.0.1/8 > done eth0 device: nVidia Corporation MCP51 Ethernet Controller (rev > a3) > eth0 configuration: eth-id-00:18:f3:89:05:4c > eth0 (DHCP) . IP/Netmask: 192.168.1.1 / 255.255.255.0 > doneSetting up service network . . . . . . . . . . . . . . . > .done > Mount SMB/ CIFS File Systems unused > <notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ > CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux > ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 > COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg > PREVLEVEL=N acpi=off LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/sbin/portmap ] > Starting RPC portmap daemondone > Importing Net File System (NFS)unused > Checking/updating CPU microcode unused > <notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ > CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux > ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 > COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg > PREVLEVEL=N acpi=off LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/usr/sbin/nscd ] > Starting Name Service Cache Daemondone > <notice>killproc: kill(2445,20) > <notice>killproc: kill(2428,1) > <notice>killproc: kill(2445,18) > <notice>killproc: kill(2445,12) > <notice>startproc: execve (/sbin/auditd) [ /sbin/auditd -n ], [ > CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux > ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 > COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg > PREVLEVEL=N acpi=off LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/sbin/auditd ] > Starting nfsboot (sm-notify) done > <notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o > PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 > SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX > INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=124 > PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg > PREVLEVEL=N acpi=off LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/usr/sbin/sshd ] > Starting SSH daemondone > Starting auditd done > Starting ZENworks Management Daemondone > <notice>startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -v > 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=5 > PREVLEVEL=N DAEMON=/usr/sbin/powersaved ] > Starting powersaved: done > Starting mail service (Postfix)done > <notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ > CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux > ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 > COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg > PREVLEVEL=N acpi=off LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes > ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc DAEMON=/usr/sbin/cron ] > Starting CRON daemondone > Starting service kdm<notice>startproc: execve (/opt/kde3/bin/kdm) [ > /opt/kde3/bin/kdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux > SHELL=/bin/sh ROOTFS_FSCK=0 INIT_VERSION=sysvinit-2.86 KDEROOTHOME=/root/.kdm > REDIRECT=/dev/tty1 COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 > RUNLEVEL=5 > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PWD=/ > LANG=en_US.UTF-8 PREVLEVEL=N LINES=44 acpi=off > QT_SYSTEM_DIR=/usr/share/desktop-data SHLVL=2 HOME=/ > XCURSOR_THEME=crystalwhite WINDOWMANAGER=/usr/bin/kde SPLASH=yes > splash=silent ROOTFS_BLKDEV=/dev/sda6 _=/sbin/startproc > DAEMON=/opt/kde3/bin/kdm ] > done > <notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ > CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux > ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 > COLUMNS=124 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 PWD=/ > SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg > PREVLEVEL=N acpi=off LINES=44 HOME=/ SHLVL=2 splash=silent SPLASH=yes > ROOTFS_BLKDEV=/dev/sda6 _=/usr/bin/ionice DAEMON=/usr/sbin/cupsd ] > Starting service kdmdone > Starting cupsddone > Starting Firewall Initialization (phase 2 of 2) SuSEfirewall2: Warning: > ip6tables does not support state matching. Extended IPv6 support disabled. > done > Master Resource Control: runlevel 5 has been reached > Skipped services in runlevel 5: acpid irq_balancer smbfs nfs microcode > <notice>killproc: kill(2347,3)
Let me say that I'm a total newbie (too ? :). had the same problem with my hp pavilion. Tried a lot concerning the USB. Finally ran an update installation on the full installation with all my USB gear connected (memcard, printer, USB 2.0 card, ext. harddisk Maxtor, bluetooth usb) , and suse 10.2 found everything concerning the USB's. maybe worth a try ? best. niels -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.5 (GNU/Linux) Comment: Using GnuPG with SUSE - http://enigmail.mozdev.org iD8DBQFFoXUU0F77CaBDYxMRAmRwAJ4te4ea5Py37Xk8KaPsYA+aQplbmwCeKpDK RNcpfXFXHPw/1vPd71ZIt9E= =MONj -----END PGP SIGNATURE----- -- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
