On Thu, 2007-01-11 at 19:05 +0100, Roger Oberholtzer wrote: > On Thu, 2007-01-11 at 07:51 +0000, [EMAIL PROTECTED] wrote: > > -------------- Original message ---------------------- > > From: Roger Oberholtzer <[EMAIL PROTECTED]> > > > On Wed, 2007-01-10 at 19:45 -0600, Billie Erin Walsh wrote: > > > > On 01/10/2007 Art Fore wrote: > > > > > How does one get two networking cards to go at the same time in Suse > > > > > Linux 10.2? I have eth0 which is wired network, and eth1 which is > > > > > Wireless. If I connect to the wireless using network manager, it > > > > > disconnects the eth0 network, connects to the wireless eth1 for a few > > > > > seconds, disconnects eth1, then goes back to the eth0. > > > > > > > > I have two wired network cards on separate networks. I can switch back > > > > and forth between them and the connections stay stable. I'm with you I > > > > would like to know if there is a way to get both active at the same > > > > time. Something like the old dual line modems. > > > > > > Are you trying to put both interfaces on the same network (both have the > > > same net mask)? That is problematic. Otherwise there is no trouble with > > > multiple cards. My wireless network is different from my wire one, so it > > > 'just works'. with two cards. In fact, in our products, we always have > > > two cards - and two different networks. > > > > > > Having said that, there is one small issue with YasT that has been this > > > way for years. It will not let you give different names to the cards. > > > After assigning the system name, it is applied to both cards. So, you > > > need to edit /etc/hosts and give one card (IP address) a different name. > > > That is the only issue I have ever had. > > > > > > -- > > > Roger Oberholtzer > > > > > > OPQ Systems AB > > > Ramböll Sverige AB > > > Kapellgränd 7 > > > P.O. Box 4205 > > > SE-102 65 Stockholm, Sweden > > > > > > Tel: Int +46 8-615 60 20 > > > Fax: Int +46 8-31 42 23 > > > > > > -- > > > To unsubscribe, e-mail: [EMAIL PROTECTED] > > > For additional commands, e-mail: [EMAIL PROTECTED] > > > > > > > No, they are two different networks. The network cards are already two > > different names, eth0 and eth1 > > > > Here is output from route > > Destination Gateway Genmask Flags Metric Ref Use > > Iface > > 10.37.129.0 * 255.255.255.0 U 0 0 0 > > vnic0 > > 10.18.32.0 * 255.255.255.0 U 0 0 0 eth0 > > 192.168.99.0 * 255.255.255.0 U 0 0 0 eth1 > > link-local * 255.255.0.0 U 0 0 0 eth0 > > loopback * 255.0.0.0 U 0 0 0 lo > > default 10.18.32.1 0.0.0.0 UG 0 0 0 eth0 > > > > Guess I need default to go to 192.168.99.1 but have not figured out how. I > > can ping eth1 IP address with no problem from linux. > > Simple. It can be done in Yast where you configure the cards. In > Advanced Options or something like that. It is called the default > gateway. On the 192.168.99.1 network, is there a gateway or a switch or > something? Give that IP address as the gateway and all will just work. > > -- > Roger Oberholtzer > > OPQ Systems AB > Ramböll Sverige AB > Kapellgränd 7 > P.O. Box 4205 > SE-102 65 Stockholm, Sweden > > Tel: Int +46 8-615 60 20 > Fax: Int +46 8-31 42 23 > For some reason or another, the gateway entry block in Yast is greyed out.
Art -- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
