I am running open suse 10.2. I am trying to read a USB. When I place my smaller USB stick, it mounts (256 Mb). When I place the 2 GB stick, it fails to mount the stick. I am running Gnome on my system.
I know the stick is operating because when I try it on 10.0 and 10.1, they are mounted successfully by the system. On the other systems they mount as /dev/sda (2 Gb) as oppose to /dev/sda1 (256Mb). I get the following messages from dmesg: USB Mass Storage support registered. Vendor: UFD Model: Flash Disk Rev: 2.00 Type: Direct-Access ANSI SCSI revision: 02 SCSI device sda: 4089855 512-byte hdwr sectors (2094 MB) sda: Write Protect is off sda: Mode Sense: 0b 00 00 08 sda: assuming drive cache: write through SCSI device sda: 4089855 512-byte hdwr sectors (2094 MB) sda: Write Protect is off sda: Mode Sense: 0b 00 00 08 sda: assuming drive cache: write through sda: unknown partition table sd 2:0:0:0: Attached scsi removable disk sda usb-storage: device scan complete sd 2:0:0:0: Attached scsi generic sg0 type 0 SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:0e:a6:aa:8d:ef:08:00 SRC=192.168.25.30 DST=224.0.0.251 LEN=72 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PRO TO=UDP SPT=5353 DPT=5353 LEN=52 SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:0e:a6:aa:8d:ef:08:00 SRC=192.168.25.30 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PR OTO=UDP SPT=5353 DPT=5353 LEN=86 SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:0e:a6:aa:8d:ef:08:00 SRC=192.168.25.30 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PR OTO=UDP SPT=5353 DPT=5353 LEN=86 usb 1-3: reset high speed USB device using ehci_hcd and address 2 usb 1-3: device descriptor read/all, error -71 usb 1-3: reset high speed USB device using ehci_hcd and address 2 usb 1-3: device descriptor read/64, error -71 usb 1-3: device descriptor read/64, error -71 usb 1-3: reset high speed USB device using ehci_hcd and address 2 SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:0e:a6:aa:8d:ef:08:00 SRC=192.168.25.30 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PR OTO=UDP SPT=5353 DPT=5353 LEN=86 usb 1-3: device not accepting address 2, error -71 usb 1-3: reset high speed USB device using ehci_hcd and address 2 usb 1-3: device not accepting address 2, error -71 usb 1-3: USB disconnect, address 2 sd 2:0:0:0: scsi: Device offlined - not ready after error recovery scsi 2:0:0:0: SCSI error: return code = 0x00010000 end_request: I/O error, dev sda, sector 10 scsi 2:0:0:0: SCSI error: return code = 0x00010000 end_request: I/O error, dev sda, sector 600 FAT: FAT read failed (blocknr 10) scsi 2:0:0:0: rejecting I/O to dead device FAT: FAT read failed (blocknr 4) scsi 2:0:0:0: rejecting I/O to dead device FAT: FAT read failed (blocknr 4) scsi 2:0:0:0: rejecting I/O to dead device FAT: FAT read failed (blocknr 4) VFS: busy inodes on changed media. scsi 2:0:0:0: rejecting I/O to dead device scsi 2:0:0:0: rejecting I/O to dead device scsi 2:0:0:0: rejecting I/O to dead device scsi 2:0:0:0: rejecting I/O to dead device sda : READ CAPACITY failed. sda : status=0, message=00, host=1, driver=00 sda : sense not available. scsi 2:0:0:0: rejecting I/O to dead device sda: Write Protect is off sda: Mode Sense: 00 00 00 00 sda: assuming drive cache: write through scsi 2:0:0:0: rejecting I/O to dead device FAT: Directory bread(block 600) failed scsi 2:0:0:0: rejecting I/O to dead device FAT: Directory bread(block 601) failed scsi 2:0:0:0: rejecting I/O to dead device FAT: Directory bread(block 602) failed scsi 2:0:0:0: rejecting I/O to dead device FAT: Directory bread(block 603) failed scsi 2:0:0:0: rejecting I/O to dead device FAT: Directory bread(block 604) failed scsi 2:0:0:0: rejecting I/O to dead device FAT: Directory bread(block 605) failed scsi 2:0:0:0: rejecting I/O to dead device -- Joseph Loo [EMAIL PROTECTED] -- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
