kernel.2k5 wrote: > Hi , > As u explain below , i have done the settings and after that i have > attached this latest dmesg OUTPUT , kindly see an attached file of > Suse 10.2 32bit default kernel. >
This is weird... It can't get any available IRQ, probably... Try the following: remove the lines exclude irq 3 and exclude irq 4 from /etc/pcmcia/config.opts and disable your COM ports ( BIOS ) and see if the log continues show the same. > > Infact there are more than 300 people facing same problem with Same > card and they are now planning to terminate and go for > Huwai USB Serial driver Data card. > This one works ok with me... > I think we must think serious abut this problem and near future make > solution fr the same ,which really help to gain more > linux confidence among new LAPTOP Linux Users,even some are like me > ready to pay ,but to whom we should contact. > Welcome to the club... > > Again Thanks For the Support. > No problem :) > > Rui Santos wrote: > >> kernel.2k5 wrote: >> >> >>> Hello Rui Santos, >>> >>> >>> >> Hi SM, >> >> >> >>> Thanks For reply , as discussed i have attached all the logs required >>> ,some are taken while booting with default kernel and some are with latest >>> re-compiled -2.6.20-4 kernel. >>> >>> Plz See an attached logs . >>> >>> Thanking you All !!! >>> >>> >>> >> The last for lines, >> >> pccard: PCMCIA card inserted into slot 0 >> cs: memory probe 0xa0000000-0xa0ffffff: clean. >> pcmcia: registering new device pcmcia0.0 >> serial_cs: serial8250_register_port() at 0x02e8, irq 3 failed >> >> specially the last one, tells you that maybe, IRQ is busy... >> >> try to add these two lines to /etc/pcmcia/config.opts >> >> exclude irq 4 >> exclude irq 3 >> >> After that remove your pcmcia device, wait 10 secs. and reinsert it, and >> watch your dmesg, to see if the log changes. >> >> REMARK: PCMCIA is undergoing a lot of changes. try it with openSUSE's >> default kernel also. >> >> >> >>> Regards >>> SM. >>> >>> >>> >> Rui >> >> >> >>> Rui Santos wrote: >>> >>> >>> >>>> kernel.2k5 wrote: >>>> >>>> >>>> >>>> >>>>> HI , >>>>> >>>>> Can any body provide me the support to configure my PCMCIA CDMA MODEM . >>>>> >>>>> >>>>> >>>>> >>>>> >>>> I've setup a few from other brands. >>>> Usually, these kind of devices provide either 2 serial ports, or a USB >>>> Hub with two serial ports. >>>> >>>> Can you start with the Device plugged out, wait for the system to become >>>> quiet, plug in the device. >>>> >>>> Then wait 10 seconds, as root type 'dmesg > log.txt'. then can you post >>>> both that log.txt and /var/log/messages file? >>>> >>>> >>>> >>>> >>>> >>>>> Or Kindly suggest me where i can get PAID support to Suse Linux for >>>>> this problem . >>>>> >>>>> Its Very urgent i cant do more R&D . >>>>> >>>>> The Details of the Modem are given Below. >>>>> >>>>> http://www.google.co.in/search?q=ZTE+MC315%2B+pcmcia+card&start=0&ie=utf-8&oe=utf-8&client=firefox-a&rls=org.mozilla:en-US:official >>>>> >>>>> http://graceice.en.ec21.com/product_detail.jsp?group_id=GC01592290&product_id=CA01623169&product_nm=ZTE_MC315_CDMA_1X_Wireless_Internet_Card >>>>> >>>>> Plz Help. >>>>> >>>>> Thanking You All. >>>>> >>>>> Regards, >>>>> >>>>> SM. >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>> >>>> >>>> >>>> >> >> > > > ------------------------------------------------------------------------ > > Linux version 2.6.18.8-0.1-default ([EMAIL PROTECTED]) (gcc version 4.1.2 > 20061115 (prerelease) (SUSE Linux)) #1 SMP Fri Mar 2 13:51:59 UTC 2007 > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000d8000 - 00000000000e0000 (reserved) > BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 0000000026f70000 (usable) > BIOS-e820: 0000000026f70000 - 0000000026f7f000 (ACPI data) > BIOS-e820: 0000000026f7f000 - 0000000026f80000 (ACPI NVS) > BIOS-e820: 0000000026f80000 - 0000000027000000 (reserved) > BIOS-e820: 0000000036f80000 - 0000000037000000 (reserved) > BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) > 0MB HIGHMEM available. > 623MB LOWMEM available. > On node 0 totalpages: 159600 > DMA zone: 4096 pages, LIFO batch:0 > Normal zone: 155504 pages, LIFO batch:31 > DMI 2.3 present. > Using APIC driver default > IO/L-APIC allowed because system is MP or new enough > ACPI: RSDP (v000 PTLTD ) @ 0x000f6ae0 > ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x26f78e81 > ACPI: FADT (v001 ATI Salmon 0x06040000 ATI 0x000f4240) @ 0x26f7ef64 > ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x26f7efd8 > ACPI: DSDT (v001 ATI MS2_1535 0x06040000 MSFT 0x0100000e) @ 0x00000000 > ATI board detected. Disabling timer routing over 8254. > ACPI: PM-Timer IO Port: 0x8008 > Allocating PCI resources starting at 40000000 (gap: 37000000:c8f80000) > Detected 2392.455 MHz processor. > Built 1 zonelists. Total pages: 159600 > Kernel command line: root=/dev/hda10 vga=791 resume=/dev/hda9 splash=silent > bootsplash: silent mode. > Local APIC disabled by BIOS -- you can enable it with "lapic" > mapped APIC to ffffd000 (014ec000) > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Initializing CPU#0 > PID hash table entries: 4096 (order: 12, 16384 bytes) > Console: colour dummy device 80x25 > Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) > Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) > Memory: 625448k/638400k available (1697k kernel code, 12284k reserved, 972k > data, 196k init, 0k highmem) > Checking if this processor honours the WP bit even in supervisor mode... Ok. > Calibrating delay using timer specific routine.. 4788.64 BogoMIPS > (lpj=9577281) > Security Framework v1.0.0 initialized > Mount-cache hash table entries: 512 > CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 > 00004400 00000000 00000000 > CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000 > 00004400 00000000 00000000 > CPU: Trace cache: 12K uops, L1 D cache: 8K > CPU: L2 cache: 256K > CPU: Hyper-Threading is disabled > CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080 00004400 > 00000000 00000000 > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > CPU0: Intel P4/Xeon Extended MCE MSRs (12) available > CPU0: Thermal monitoring enabled > Compat vDSO mapped to ffffe000. > Checking 'hlt' instruction... OK. > SMP alternatives: switching to UP code > Freeing SMP alternatives: 16k freed > checking if image is initramfs... it is > Freeing initrd memory: 3158k freed > ACPI: Core revision 20060707 > ACPI: setting ELCR to 0200 (from 0420) > CPU0: Intel Mobile Intel(R) Celeron(R) CPU 2.40GHz stepping 09 > SMP motherboard not detected. > Local APIC not detected. Using dummy APIC emulation. > Brought up 1 CPUs > migration_cost=0 > NET: Registered protocol family 16 > ACPI: bus type pci registered > PCI: PCI BIOS revision 2.10 entry at 0xfd89b, last bus=2 > PCI: Using configuration type 1 > Setting up standard PCI resources > ACPI: Interpreter enabled > ACPI: Using PIC for interrupt routing > ACPI: PCI Root Bridge [PCI0] (0000:00) > PCI: Probing PCI hardware (bus 00) > PCI quirk: region 8000-803f claimed by ali7101 ACPI > PCI quirk: region 8040-805f claimed by ali7101 SMB > Boot video device is 0000:01:05.0 > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] > ACPI: PCI Interrupt Link [LNK0] (IRQs 7 10) *0, disabled. > ACPI: PCI Interrupt Link [LNK1] (IRQs 7 *10) > ACPI: PCI Interrupt Link [LNK2] (IRQs 7 10) *0, disabled. > ACPI: PCI Interrupt Link [LNK3] (IRQs 7 10) *0, disabled. > ACPI: PCI Interrupt Link [LNK4] (IRQs 7 10) *0, disabled. > ACPI: PCI Interrupt Link [LNK5] (IRQs 7 *11) > ACPI: PCI Interrupt Link [LNK6] (IRQs 7 10) *0, disabled. > ACPI: PCI Interrupt Link [LNK7] (IRQs *5) > ACPI: PCI Interrupt Link [LNK8] (IRQs 7 *10) > ACPI: Embedded Controller [EC0] (gpe 24) interrupt mode. > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI init > pnp: PnP ACPI: found 11 devices > PnPBIOS: Disabled by ACPI PNP > PCI: Using ACPI for IRQ routing > PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report > pnp: 00:07: ioport range 0x40b-0x40b has been reserved > pnp: 00:07: ioport range 0x480-0x48f has been reserved > pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved > pnp: 00:07: ioport range 0x4d6-0x4d6 has been reserved > pnp: 00:07: ioport range 0x8000-0x807f could not be reserved > PCI: Bridge: 0000:00:01.0 > IO window: 9000-9fff > MEM window: d4300000-d43fffff > PREFETCH window: dc000000-dfffffff > PCI: Bus 2, cardbus bridge: 0000:00:0a.0 > IO window: 00001800-000018ff > IO window: 00001c00-00001cff > PREFETCH window: 40000000-41ffffff > MEM window: 42000000-43ffffff > PCI: Enabling device 0000:00:0a.0 (0005 -> 0007) > ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 11 > PCI: setting IRQ 11 as level-triggered > ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNK5] -> GSI 11 (level, low) -> > IRQ 11 > NET: Registered protocol family 2 > IP route cache hash table entries: 32768 (order: 5, 131072 bytes) > TCP established hash table entries: 131072 (order: 8, 1048576 bytes) > TCP bind hash table entries: 65536 (order: 7, 524288 bytes) > TCP: Hash tables configured (established 131072 bind 65536) > TCP reno registered > Simple Boot Flag at 0x37 set to 0x1 > Machine check exception polling timer started. > apm: BIOS not found. > audit: initializing netlink socket (disabled) > audit(1175713488.972:1): initialized > Total HugeTLB memory allocated, 0 > VFS: Disk quotas dquot_6.5.1 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > Initializing Cryptographic API > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > Activating ISA DMA hang workarounds. > vesafb: framebuffer at 0xdc000000, mapped to 0xe7880000, using 6144k, total > 16320k > vesafb: mode is 1024x768x16, linelength=2048, pages=9 > vesafb: protected mode interface info at c000:51bf > vesafb: pmi: set display start = c00c5253, set palette = c00c529f > vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4 > vesafb: scrolling: redraw > vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 > bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 81749 > bytes,<6>...found (1024x768, 46202 bytes, v3). > Console: switching to colour frame buffer device 124x44 > fb0: VESA VGA frame buffer device > isapnp: Scanning for PnP cards... > isapnp: No Plug & Play device found > Real Time Clock Driver v1.12ac > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > PCI: Enabling device 0000:00:08.0 (0000 -> 0003) > ACPI: PCI Interrupt Link [LNK6] enabled at IRQ 10 > PCI: setting IRQ 10 as level-triggered > ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNK6] -> GSI 10 (level, low) -> > IRQ 10 > 0000:00:08.0: ttyS2 at I/O 0x1428 (irq = 10) is a 8250 > 0000:00:08.0: ttyS3 at I/O 0x1440 (irq = 10) is a 8250 > Couldn't register serial port 0000:00:08.0: -28 > floppy0: no floppy controllers found > RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize > PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 > serio: i8042 AUX port at 0x60,0x64 irq 12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > mice: PS/2 mouse device common for all mice > input: PC Speaker as /class/input/input0 > input: AT Translated Set 2 keyboard as /class/input/input1 > md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 > md: bitmap version 4.39 > NET: Registered protocol family 1 > Using IPI No-Shortcut mode > ACPI: (supports S0 S3 S4 S5) > Time: tsc clocksource has been installed. > Freeing unused kernel memory: 196k freed > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > ACPI: Processor [CPU0] (supports 8 throttling states) > input: ImPS/2 Generic Wheel Mouse as /class/input/input2 > ACPI: Thermal Zone [THRM] (71 C) > ALI15X3: IDE controller at PCI slot 0000:00:10.0 > ACPI: Unable to derive IRQ for device 0000:00:10.0 > ACPI: PCI Interrupt 0000:00:10.0[A]: no GSI > ALI15X3: chipset revision 196 > ALI15X3: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0x2000-0x2007, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0x2008-0x200f, BIOS settings: hdc:DMA, hdd:pio > Probing IDE interface ide0... > Time: acpi_pm clocksource has been installed. > hda: HTS541080G9AT00, ATA DISK drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > hda: max request size: 128KiB > hda: 156301488 sectors (80026 MB) w/7539KiB Cache, CHS=16383/255/63, UDMA(100) > hda: cache flushes supported > hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > > Probing IDE interface ide1... > hdc: QSI CD-ROM SCR-242, ATAPI CD/DVD-ROM drive > ide1 at 0x170-0x177,0x376 on irq 15 > BIOS EDD facility v0.16 2004-Jun-25, 2 devices found > Attempting manual resume > kjournald starting. Commit interval 5 seconds > EXT3 FS on hda10, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > parport: PnPBIOS parport detected. > parport0: PC-style at 0x378 (0x778), irq 7, dma 0 > [PCSPP,TRISTATE,COMPAT,ECP,DMA] > lp0: using parport0 (interrupt-driven). > usbcore: registered new driver usbfs > usbcore: registered new driver hub > ali15x3_smbus 0000:00:11.0: ALI15X3_smb region uninitialized - upgrade BIOS > or use force_addr=0xaddr > ali15x3_smbus 0000:00:11.0: ALI15X3 not detected, module not inserted. > Yenta: CardBus bridge found at 0000:00:0a.0 [103c:002a] > Yenta O2: res at 0x94/0xD4: 00/ea > Yenta O2: enabling read prefetch/write burst > ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) > Linux agpgart interface v0.101 (c) Dave Jones > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > Yenta: ISA IRQ mask 0x0438, PCI irq 11 > Socket status: 30000811 > ACPI: PCI Interrupt Link [LNK8] enabled at IRQ 10 > ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNK8] -> GSI 10 (level, low) -> > IRQ 10 > ohci_hcd 0000:00:02.0: OHCI Host Controller > ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 > ohci_hcd 0000:00:02.0: irq 10, io mem 0xd4000000 > ieee1394: Initialized config rom entry `ip1394' > usb usb1: new device found, idVendor=0000, idProduct=0000 > usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: OHCI Host Controller > usb usb1: Manufacturer: Linux 2.6.18.8-0.1-default ohci_hcd > usb usb1: SerialNumber: 0000:00:02.0 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 4 ports detected > natsemi dp8381x driver, version 2.0, June 27, 2006 > originally by Donald Becker <[EMAIL PROTECTED]> > http://www.scyld.com/network/natsemi.html > 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder > agpgart: Detected Ati IGP330/340/345/350/M chipset > agpgart: AGP aperture is 64M @ 0xd8000000 > PCI: Enabling device 0000:00:0c.0 (0010 -> 0012) > ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNK5] -> GSI 11 (level, low) -> > IRQ 11 > ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[d4008000-d40087ff] > Max Packet=[2048] IR/IT contexts=[4/8] > shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 > ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10 > ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> > IRQ 10 > natsemi eth0: NatSemi DP8381[56] at 0xd4009000 (0000:00:12.0), > 00:0d:9d:86:8a:f4, IRQ 10, port TP. > PCI: Enabling device 0000:00:06.0 (0005 -> 0007) > ACPI: PCI Interrupt Link [LNK7] enabled at IRQ 5 > PCI: setting IRQ 5 as level-triggered > ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNK7] -> GSI 5 (level, low) -> > IRQ 5 > usb 1-2: new full speed USB device using ohci_hcd and address 2 > pccard: PCMCIA card inserted into slot 0 > usb 1-2: new device found, idVendor=067b, idProduct=2507 > usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=3 > usb 1-2: Product: Mass Storage Device > usb 1-2: Manufacturer: Prolific Technology Inc. > usb 1-2: SerialNumber: 00 > usb 1-2: configuration #1 chosen from 1 choice > hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33) > Uniform CD-ROM driver Revision: 3.20 > SCSI subsystem initialized > ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d9d719f84c2b7] > Initializing USB Mass Storage driver... > scsi0 : SCSI emulation for USB Mass Storage devices > usb-storage: device found at 2 > usb-storage: waiting for device to settle before scanning > usbcore: registered new driver usb-storage > USB Mass Storage support registered. > cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 > 0x388-0x38f > cs: IO port probe 0x3e0-0x4ff: clean. > cs: IO port probe 0x820-0x8ff: clean. > cs: IO port probe 0xc00-0xcf7: clean. > cs: IO port probe 0xa00-0xaff: clean. > cs: memory probe 0xa0000000-0xa0ffffff: clean. > pcmcia: registering new device pcmcia0.0 > IRQ handler type mismatch for IRQ 5 > [<c01465e9>] setup_irq+0x17d/0x190 > [<e81fc6a7>] test_action+0x0/0x3 [pcmcia] > [<c0146678>] request_irq+0x7c/0x98 > [<e81fcb2c>] pcmcia_request_irq+0xe6/0x1df [pcmcia] > [<e825d8db>] serial_probe+0x62d/0x792 [serial_cs] > [<c01249f4>] current_fs_time+0x4f/0x5b > [<c01635e0>] do_truncate+0x5f/0x68 > [<e81fc31b>] pcmcia_device_probe+0x66/0xf3 [pcmcia] > [<c0225775>] really_probe+0x39/0x9d > [<c022580a>] driver_probe_device+0x31/0x87 > [<c0225860>] __device_attach+0x0/0x5 > [<c022517b>] bus_for_each_drv+0x39/0x60 > [<c0224db7>] bus_rescan_devices_helper+0x0/0x46 > [<c02258b1>] device_attach+0x4c/0x5d > [<c0225860>] __device_attach+0x0/0x5 > [<c0224de4>] bus_rescan_devices_helper+0x2d/0x46 > [<c0225252>] bus_for_each_dev+0x39/0x5b > [<c0225287>] bus_rescan_devices+0x13/0x15 > [<c0224db7>] bus_rescan_devices_helper+0x0/0x46 > [<e81fb046>] pcmcia_store_allow_func_id_match+0x46/0x4c [pcmcia] > [<e81fb000>] pcmcia_store_allow_func_id_match+0x0/0x4c [pcmcia] > [<c0223961>] dev_attr_store+0x24/0x29 > [<c019bb87>] sysfs_write_file+0x90/0xb7 > [<c019baf7>] sysfs_write_file+0x0/0xb7 > [<c0164dd1>] vfs_write+0xa8/0x15f > [<c0165407>] sys_write+0x41/0x67 > [<c0103d5d>] sysenter_past_esp+0x56/0x79 > IRQ handler type mismatch for IRQ 10 > [<c01465e9>] setup_irq+0x17d/0x190 > [<e81fc6a7>] test_action+0x0/0x3 [pcmcia] > [<c0146678>] request_irq+0x7c/0x98 > [<e81fcb2c>] pcmcia_request_irq+0xe6/0x1df [pcmcia] > [<e825d8db>] serial_probe+0x62d/0x792 [serial_cs] > [<c01249f4>] current_fs_time+0x4f/0x5b > [<c01635e0>] do_truncate+0x5f/0x68 > [<e81fc31b>] pcmcia_device_probe+0x66/0xf3 [pcmcia] > [<c0225775>] really_probe+0x39/0x9d > [<c022580a>] driver_probe_device+0x31/0x87 > [<c0225860>] __device_attach+0x0/0x5 > [<c022517b>] bus_for_each_drv+0x39/0x60 > [<c0224db7>] bus_rescan_devices_helper+0x0/0x46 > [<c02258b1>] device_attach+0x4c/0x5d > [<c0225860>] __device_attach+0x0/0x5 > [<c0224de4>] bus_rescan_devices_helper+0x2d/0x46 > [<c0225252>] bus_for_each_dev+0x39/0x5b > [<c0225287>] bus_rescan_devices+0x13/0x15 > [<c0224db7>] bus_rescan_devices_helper+0x0/0x46 > [<e81fb046>] pcmcia_store_allow_func_id_match+0x46/0x4c [pcmcia] > [<e81fb000>] pcmcia_store_allow_func_id_match+0x0/0x4c [pcmcia] > [<c0223961>] dev_attr_store+0x24/0x29 > [<c019bb87>] sysfs_write_file+0x90/0xb7 > [<c019baf7>] sysfs_write_file+0x0/0xb7 > [<c0164dd1>] vfs_write+0xa8/0x15f > [<c0165407>] sys_write+0x41/0x67 > [<c0103d5d>] sysenter_past_esp+0x56/0x79 > IRQ handler type mismatch for IRQ 5 > [<c01465e9>] setup_irq+0x17d/0x190 > [<e81fc6a7>] test_action+0x0/0x3 [pcmcia] > [<c0146678>] request_irq+0x7c/0x98 > [<e81fcb2c>] pcmcia_request_irq+0xe6/0x1df [pcmcia] > [<e825d8db>] serial_probe+0x62d/0x792 [serial_cs] > [<c01249f4>] current_fs_time+0x4f/0x5b > [<c01635e0>] do_truncate+0x5f/0x68 > [<e81fc31b>] pcmcia_device_probe+0x66/0xf3 [pcmcia] > [<c0225775>] really_probe+0x39/0x9d > [<c022580a>] driver_probe_device+0x31/0x87 > [<c0225860>] __device_attach+0x0/0x5 > [<c022517b>] bus_for_each_drv+0x39/0x60 > [<c0224db7>] bus_rescan_devices_helper+0x0/0x46 > [<c02258b1>] device_attach+0x4c/0x5d > [<c0225860>] __device_attach+0x0/0x5 > [<c0224de4>] bus_rescan_devices_helper+0x2d/0x46 > [<c0225252>] bus_for_each_dev+0x39/0x5b > [<c0225287>] bus_rescan_devices+0x13/0x15 > [<c0224db7>] bus_rescan_devices_helper+0x0/0x46 > [<e81fb046>] pcmcia_store_allow_func_id_match+0x46/0x4c [pcmcia] > [<e81fb000>] pcmcia_store_allow_func_id_match+0x0/0x4c [pcmcia] > [<c0223961>] dev_attr_store+0x24/0x29 > [<c019bb87>] sysfs_write_file+0x90/0xb7 > [<c019baf7>] sysfs_write_file+0x0/0xb7 > [<c0164dd1>] vfs_write+0xa8/0x15f > [<c0165407>] sys_write+0x41/0x67 > [<c0103d5d>] sysenter_past_esp+0x56/0x79 > IRQ handler type mismatch for IRQ 10 > [<c01465e9>] setup_irq+0x17d/0x190 > [<e81fc6a7>] test_action+0x0/0x3 [pcmcia] > [<c0146678>] request_irq+0x7c/0x98 > [<e81fcb2c>] pcmcia_request_irq+0xe6/0x1df [pcmcia] > [<e825d8db>] serial_probe+0x62d/0x792 [serial_cs] > [<c01249f4>] current_fs_time+0x4f/0x5b > [<c01635e0>] do_truncate+0x5f/0x68 > [<e81fc31b>] pcmcia_device_probe+0x66/0xf3 [pcmcia] > [<c0225775>] really_probe+0x39/0x9d > [<c022580a>] driver_probe_device+0x31/0x87 > [<c0225860>] __device_attach+0x0/0x5 > [<c022517b>] bus_for_each_drv+0x39/0x60 > [<c0224db7>] bus_rescan_devices_helper+0x0/0x46 > [<c02258b1>] device_attach+0x4c/0x5d > [<c0225860>] __device_attach+0x0/0x5 > [<c0224de4>] bus_rescan_devices_helper+0x2d/0x46 > [<c0225252>] bus_for_each_dev+0x39/0x5b > [<c0225287>] bus_rescan_devices+0x13/0x15 > [<c0224db7>] bus_rescan_devices_helper+0x0/0x46 > [<e81fb046>] pcmcia_store_allow_func_id_match+0x46/0x4c [pcmcia] > [<e81fb000>] pcmcia_store_allow_func_id_match+0x0/0x4c [pcmcia] > [<c0223961>] dev_attr_store+0x24/0x29 > [<c019bb87>] sysfs_write_file+0x90/0xb7 > [<c019baf7>] sysfs_write_file+0x0/0xb7 > [<c0164dd1>] vfs_write+0xa8/0x15f > [<c0165407>] sys_write+0x41/0x67 > [<c0103d5d>] sysenter_past_esp+0x56/0x79 > pcmcia: request for exclusive IRQ could not be fulfilled. > pcmcia: the driver needs updating to supported shared IRQ lines. > serial_cs: serial8250_register_port() at 0x02e8, irq 11 failed > Vendor: ST940211 Model: 3A Rev: 3.05 > Type: Direct-Access ANSI SCSI revision: 00 > usb-storage: device scan complete > SCSI device sda: 78140159 512-byte hdwr sectors (40008 MB) > sda: Write Protect is off > sda: Mode Sense: 03 00 00 00 > sda: assuming drive cache: write through > SCSI device sda: 78140159 512-byte hdwr sectors (40008 MB) > sda: Write Protect is off > sda: Mode Sense: 03 00 00 00 > sda: assuming drive cache: write through > sda: sda1 sda2 < sda5 sda6 sda7 > > sd 0:0:0:0: Attached scsi disk sda > sd 0:0:0:0: Attached scsi generic sg0 type 0 > ALSA sound/pci/ac97/ac97_codec.c:1923: AC'97 1 does not respond - RESET > ALSA sound/pci/ac97/ac97_codec.c:1932: AC'97 1 access is not valid > [0xffffffff], removing mixer. > ALSA sound/pci/ali5451/ali5451.c:1977: ali mixer 1 creating error. > Adding 931728k swap on /dev/hda9. Priority:-1 extents:1 across:931728k > device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [EMAIL PROTECTED] > loop: loaded (max 8 devices) > ReiserFS: hda8: found reiserfs format "3.6" with standard journal > ReiserFS: hda8: using ordered data mode > reiserfs: using flush barriers > ReiserFS: hda8: journal params: device hda8, size 8192, journal first block > 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 > ReiserFS: hda8: checking transaction log (hda8) > ReiserFS: hda8: Using r5 hash to sort names > ReiserFS: hda7: found reiserfs format "3.6" with standard journal > ReiserFS: hda7: using ordered data mode > reiserfs: using flush barriers > ReiserFS: hda7: journal params: device hda7, size 8192, journal first block > 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 > ReiserFS: hda7: checking transaction log (hda7) > ReiserFS: hda7: Using r5 hash to sort names > kjournald starting. Commit interval 5 seconds > EXT3 FS on hda6, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > AppArmor: AppArmor initialized > audit(1175713511.418:2): AppArmor initialized > > NET: Registered protocol family 10 > lo: Disabled Privacy Extensions > IPv6 over IPv4 tunneling driver > ip6_tables: (C) 2000-2006 Netfilter Core Team > ip_tables: (C) 2000-2006 Netfilter Core Team > Netfilter messages via NETLINK v0.30. > ip_conntrack version 2.4 (4987 buckets, 39896 max) - 228 bytes per conntrack > ACPI: AC Adapter [ACAD] (on-line) > ACPI: Battery Slot [BAT1] (battery present) > ACPI: Power Button (FF) [PWRF] > ACPI: Power Button (CM) [PWRB] > ACPI: Lid Switch [LID] > powernow: This module only works with AMD K7 CPUs > eth0: DSPCFG accepted after 0 usec. > eth0: link up. > eth0: Setting full-duplex based on negotiated link capability. > audit(1175693735.300:3): audit_pid=3530 old=0 by auid=4294967295 > IA-32 Microcode Update Driver: v1.14a <[EMAIL PROTECTED]> > microcode: CPU0 updated from revision 0x10 to 0x2f, date = 08112004 > eth0: no IPv6 routers present > [drm] Initialized drm 1.0.1 20051102 > ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 10 > ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK0] -> GSI 10 (level, low) -> > IRQ 10 > [drm] Initialized radeon 1.25.0 20060524 on minor 0 > mtrr: 0xdc000000,0x4000000 overlaps existing 0xdc000000,0x1000000 > mtrr: 0xdc000000,0x4000000 overlaps existing 0xdc000000,0x1000000 > mtrr: 0xdc000000,0x4000000 overlaps existing 0xdc000000,0x1000000 > agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. > agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode > agpgart: Putting AGP V2 device at 0000:01:05.0 into 4x mode > [drm] Setting GART location based on old memory map > [drm] writeback test succeeded in 1 usecs > SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.20 DST=224.0.0.251 > LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87 > SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.20 DST=224.0.0.251 > LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87 > kjournald starting. Commit interval 5 seconds > EXT3-fs warning: maximal mount count reached, running e2fsck is recommended > EXT3 FS on sda6, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > ReiserFS: sda5: found reiserfs format "3.6" with standard journal > ReiserFS: sda5: using ordered data mode > reiserfs: using flush barriers > ReiserFS: sda5: journal params: device sda5, size 8192, journal first block > 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 > ReiserFS: sda5: checking transaction log (sda5) > ReiserFS: sda5: Using r5 hash to sort names > kjournald starting. Commit interval 5 seconds > EXT3-fs warning: maximal mount count reached, running e2fsck is recommended > EXT3 FS on sda1, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.0.20 DST=224.0.0.251 > LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87 > -- Rui Santos http://www.ruisantos.com/ Veni, vidi, Linux! -- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
