Hi All,
I want to get my wlan device D-Link USB DWL-G122-revC working after
installed 10.3. I followed Ndiswrapper on opensuse.org and there's no
error on every command instructed in it. I checked,
# ndiswrapper -l
dr71wu : driver installed
device (07D1:3C03) present (alternate driver: rt73usb)
I checked with dmesg and i think it's fine (CMIIW I attach the output
both with "grep usb" and the complete dmesg output). I added the alias
on modules.conf and there's no error on modprobe. Then i configured
Network Card with YAST as advised. The problem is i couldn't see any
wireless network available with KNetworkManager. I added my network
manually configured the same thing i use on Windows, but i still can't
connect to it. The device is there though (detected by the applet). I
tried to use the traditional ifup and put my settings through YAST.
Did i miss something to check? Please help.
Thanks,
Dida
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: configuration #1 chosen from 1 choice
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: configuration #1 chosen from 1 choice
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: configuration #1 chosen from 1 choice
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.22.5-31-default ehci_hcd
usb usb4: SerialNumber: 0000:00:1d.7
usb usb4: configuration #1 chosen from 1 choice
usb 1-1: string descriptor 0 read error: -71
usb 1-1: string descriptor 0 read error: -71
usb 1-1: new device found, idVendor=07d1, idProduct=3c03
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: configuration #1 chosen from 1 choice
sda7<3>usb 1-1: can't set config #1, error -71
usb 1-1: USB disconnect, address 2
usb 4-1: new high speed USB device using ehci_hcd and address 2
usb 4-1: new device found, idVendor=07d1, idProduct=3c03
usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-1: Product: 802.11 bg WLAN
usb 4-1: Manufacturer: Ralink
usb 4-1: configuration #1 chosen from 1 choice
usb 4-2: new high speed USB device using ehci_hcd and address 3
usb 4-2: new device found, idVendor=152d, idProduct=2336
usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=5
usb 4-2: Product: JM20336 SATA, USB Combo
usb 4-2: Manufacturer: JMicron
usb 4-2: SerialNumber: 888888888888
usb 4-2: configuration #1 chosen from 1 choice
usb 4-3: new high speed USB device using ehci_hcd and address 4
usb 4-3: new device found, idVendor=13e0, idProduct=0151
usb 4-3: new device strings: Mfr=0, Product=2, SerialNumber=3
usb 4-3: Product: USB Mass Storage Device
usb 4-3: SerialNumber: 46060630000008
usb 4-3: configuration #1 chosen from 1 choice
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
phy0 -> rt73usb_validate_eeprom: EEPROM recovery - NIC: 0xffef
phy0 -> rt73usb_validate_eeprom: EEPROM recovery - Led: 0xe000
phy0 -> rt73usb_validate_eeprom: EEPROM recovery - RSSI OFFSET BG: 0x0000
usb-storage: device scan complete
usb-storage: device scan complete
usbcore: registered new interface driver rt73usb
Linux version 2.6.22.5-31-default ([EMAIL PROTECTED]) (gcc version 4.2.1 (SUSE
Linux)) #1 SMP 2007/09/21 22:29:00 UTC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffec000 (usable)
BIOS-e820: 000000003ffec000 - 000000003ffef000 (ACPI data)
BIOS-e820: 000000003ffef000 - 000000003ffff000 (reserved)
BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 262124) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262124
early_node_map[1] active PFN ranges
0: 0 -> 262124
On node 0 totalpages: 262124
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 255 pages used for memmap
HighMem zone: 32493 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000F52E0, 0014 (r0 ASUS )
ACPI: RSDT 3FFEC000, 0030 (r1 ASUS P4PE 42302E31 MSFT 31313031)
ACPI: FACP 3FFEC0C0, 0074 (r1 ASUS P4PE 42302E31 MSFT 31313031)
ACPI: DSDT 3FFEC134, 2A43 (r1 ASUS P4PE 1000 MSFT 100000B)
ACPI: FACS 3FFFF000, 0040
ACPI: BOOT 3FFEC030, 0028 (r1 ASUS P4PE 42302E31 MSFT 31313031)
ACPI: APIC 3FFEC058, 005A (r1 ASUS P4PE 42302E31 MSFT 31313031)
ACPI: PM-Timer IO Port: 0xe408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 22 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists. Total pages: 260077
Kernel command line:
root=/dev/disk/by-id/scsi-SATA_IC35L040AVVN07-_VNP214B2SLVTZD-part8 vga=0x317
resume=/dev/sda9 splash=silent
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2004.621 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1031428k/1048496k available (1825k kernel code, 16420k reserved, 764k
data, 228k init, 130992k highmem)
virtual kernel memory layout:
fixmap : 0xffdf4000 - 0xfffff000 (2092 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc038e000 - 0xc03c7000 ( 228 kB)
.data : 0xc02c86ed - 0xc0387964 ( 764 kB)
.text : 0xc0100000 - 0xc02c86ed (1825 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4013.20 BogoMIPS (lpj=8026402)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: 3febfbff 00000000 00000000 0000b080 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
Unpacking initramfs... done
Freeing initrd memory: 4024k freed
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 327 Objects with 47 Devices 127 Methods 8 Regions
tbxface-0587 [00] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
CPU0: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
Total of 1 processors activated (4013.20 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf1e50, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int
0x16
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 7 Wake, Enabled 0 Runtime GPEs
in this block
Completing Region/Field/Buffer/Package
initialization:..........................................
Initialized 7/8 Regions 0/0 Fields 22/22 Buffers 13/13 Packages (336 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.
Executed 1 _INI methods requiring 0 _STA executions (examined 51 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
* The chipset may have PM-Timer Bug. Due to workarounds for a bug,
* this clock source is slow. If you are sure your timer does not have
* this bug, please use "acpi_pm_good" to disable the workaround
PCI: Enabled i801 SMBus device
PCI quirk: region e400-e47f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region ec00-ec3f claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 16 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
ACPI: RTC can wake from S4
pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xf0000-0xfffff could not be reserved
pnp: 00:00: iomem range 0x100000-0x3fffffff could not be reserved
pnp: 00:00: iomem range 0xfec00000-0xfec000ff could not be reserved
pnp: 00:02: ioport range 0xe400-0xe47f has been reserved
pnp: 00:02: ioport range 0xe800-0xe81f has been reserved
pnp: 00:02: ioport range 0xec00-0xec3f has been reserved
pnp: 00:02: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:02: iomem range 0xfff80000-0xffffffff could not be reserved
pnp: 00:02: iomem range 0xffb80000-0xffbfffff has been reserved
pnp: 00:0f: ioport range 0x3f0-0x3f1 has been reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: ee000000-efefffff
PREFETCH window: eff00000-f7ffffff
PCI: Bridge: 0000:00:1e.0
IO window: b000-bfff
MEM window: ed000000-ed7fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x3a set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1195306945.420:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
vesafb: framebuffer at 0xf0000000, mapped to 0xf8880000, using 6144k, total
65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:c200
vesafb: pmi: set display start = c00cc245, set palette = c00cc2ca
vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903
cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 ff03
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 78436 bytes
bootsplash: ...found (1024x768, 28133 bytes, v3).
Console: switching to colour frame buffer device 124x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
Switched to NOHz mode on CPU #0
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PC Speaker as /class/input/input1
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
NET: Registered protocol family 1
Using IPI No-Shortcut mode
Freeing unused kernel memory: 228k freed
ACPI: Invalid PBLK length [5]
ACPI Exception (processor_core-0787): AE_NOT_FOUND, Processor Device is not
present [20070126]
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.1: version 2.11
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15
ata1.00: ATA-5: IC35L040AVVN07-0, VA2OAG0A, max UDMA/100
ata1.00: 80418240 sectors, multi 16: LBA
ata1.00: configured for UDMA/100
ata2.00: ATAPI: TDK CDRW4800B, S7S4, max UDMA/33
ata2.01: ATAPI: SONY DVD RW DRU-835A, SS02, max UDMA/66
ata2.01: limited to UDMA/33 due to 40-wire cable
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA IC35L040AVVN07-0 VA2O PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM TDK CDRW4800B S7S4 PQ: 0 ANSI: 5
scsi 1:0:1:0: CD-ROM SONY DVD RW DRU-835A SS02 PQ: 0 ANSI: 5
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000d800
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000d400
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
sd 0:0:0:0: [sda] 80418240 512-byte hardware sectors (41174 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 80418240 512-byte hardware sectors (41174 MB)
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
usb 1-1: new full speed USB device using uhci_hcd and address 2
uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000d000
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.22.5-31-default uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2 < sda5 sda6<6>ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23
(level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xed800000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.22.5-31-default ehci_hcd
usb usb4: SerialNumber: 0000:00:1d.7
usb usb4: configuration #1 chosen from 1 choice
usb 1-1: string descriptor 0 read error: -71
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 1-1: string descriptor 0 read error: -71
usb 1-1: new device found, idVendor=07d1, idProduct=3c03
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: can't set config #1, error -71
sda7 sda8 sda9 >
sd 0:0:0:0: [sda] Attached SCSI disk
usb 1-1: USB disconnect, address 2
usb 4-1: new high speed USB device using ehci_hcd and address 2
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
Attempting manual resume
usb 4-1: new device found, idVendor=07d1, idProduct=3c03
usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-1: Product: 802.11 bg WLAN
usb 4-1: Manufacturer: Ralink
usb 4-1: configuration #1 chosen from 1 choice
usb 4-2: new high speed USB device using ehci_hcd and address 3
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usb 4-2: new device found, idVendor=152d, idProduct=2336
usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=5
usb 4-2: Product: JM20336 SATA, USB Combo
usb 4-2: Manufacturer: JMicron
usb 4-2: SerialNumber: 888888888888
usb 4-2: configuration #1 chosen from 1 choice
usb 4-3: new high speed USB device using ehci_hcd and address 4
usb 4-3: new device found, idVendor=13e0, idProduct=0151
usb 4-3: new device strings: Mfr=0, Product=2, SerialNumber=3
usb 4-3: Product: USB Mass Storage Device
usb 4-3: SerialNumber: 46060630000008
usb 4-3: configuration #1 chosen from 1 choice
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
scsi 1:0:1:0: Attached scsi generic sg2 type 5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 20
iTCO_vendor_support: vendor-support=0
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH4 TCO device (Version=1, TCOBASE=0xe460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
rtc_cmos: probe of 00:05 failed with error -16
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
Linux agpgart interface v0.102 (c) Dave Jones
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
gameport: NS558 PnP Gameport is pnp00:0e/gameport0, io 0x200, speed 736kHz
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
agpgart: Detected an Intel 830M Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
intel_rng: FWH not detected
Initializing USB Mass Storage driver...
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1f.5 to 64
phy0 -> rt73usb_validate_eeprom: EEPROM recovery - NIC: 0xffef
phy0 -> rt73usb_validate_eeprom: EEPROM recovery - Led: 0xe000
phy0 -> rt73usb_validate_eeprom: EEPROM recovery - RSSI OFFSET BG: 0x0000
phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 1300, rf: 0002, rev:
0002573a.
wmaster0: Selected rate control algorithm 'simple'
usbcore: registered new interface driver rt73usb
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi3 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ALSA sound/pci/ac97/ac97_codec.c:2113: AC'97 0 analog subsections not ready
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
intel8x0_measure_ac97_clock: measured 53365 usecs
intel8x0: clocking to 48000
gameport: EMU10K1 is pci0000:02:0c.1/gameport0, io 0xb400, speed 946kHz
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 20 (level, low) -> IRQ 21
eth0: Broadcom 4400 10/100BaseT Ethernet 00:e0:18:e2:5d:6a
ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 21
Adding 1638588k swap on /dev/sda9. Priority:-1 extents:1 across:1638588k
scsi 2:0:0:0: Direct-Access ST316081 3PT0 3.AA PQ: 0 ANSI: 2 CCS
sd 2:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 38 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 38 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb:<5>scsi 3:0:0:0: Direct-Access USB 2.0 Flash Drive 0.00 PQ: 0
ANSI: 2
sd 3:0:0:0: [sdc] 2015232 512-byte hardware sectors (1032 MB)
sdb1 sdb2 <<5>sd 3:0:0:0: [sdc] Write Protect is off
sd 3:0:0:0: [sdc] Mode Sense: 00 00 00 00
sd 3:0:0:0: [sdc] Assuming drive cache: write through
sdb5<5>sd 3:0:0:0: [sdc] 2015232 512-byte hardware sectors (1032 MB)
sdb6<5>sd 3:0:0:0: [sdc] Write Protect is off
sd 3:0:0:0: [sdc] Mode Sense: 00 00 00 00
sd 3:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdb7 sdc1
sd 3:0:0:0: [sdc] Attached SCSI removable disk
sdb8<5>sd 3:0:0:0: Attached scsi generic sg3 type 0
sdb9<7>usb-storage: device scan complete
sdb10 >
sd 2:0:0:0: [sdb] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg4 type 0
usb-storage: device scan complete
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED]
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.8)
AppArmor: AppArmor initialized
audit(1195306959.920:2): type=1505 info="AppArmor initialized" pid=1975
powernow: This module only works with AMD K7 CPUs
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8191 buckets, 65528 max)
phy0 -> rt2x00lib_request_firmware: Info - Loading firmware file 'rt73.bin'.
phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
audit(1195278181.328:3): audit_pid=2948 old=0 by auid=4294967295
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 0 - CWmin: 4, CWmax: 10,
Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 1 - CWmin: 4, CWmax: 10,
Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 2 - CWmin: 4, CWmax: 10,
Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 3 - CWmin: 4, CWmax: 10,
Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 4 - CWmin: 4, CWmax: 10,
Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 7 - CWmin: 5, CWmax: 10,
Aifs: 2.
IA-32 Microcode Update Driver: v1.14a <[EMAIL PROTECTED]>
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: checktime reached, running e2fsck is recommended
EXT3 FS on sdb10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.28 [Flags: R/W MODULE].
NTFS-fs warning (device sdb1): parse_options(): Option utf8 is no longer
supported, using option nls=utf8. Please use option nls=utf8 in the future and
make sure utf8 is compiled either as a module or into the kernel.
NTFS volume version 3.1.
bootsplash: status on console 0 changed to on
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 0 - CWmin: 4, CWmax: 10,
Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 1 - CWmin: 4, CWmax: 10,
Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 2 - CWmin: 4, CWmax: 10,
Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 3 - CWmin: 4, CWmax: 10,
Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 4 - CWmin: 4, CWmax: 10,
Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 7 - CWmin: 5, CWmax: 10,
Aifs: 2.
NET: Registered protocol family 17
usb 4-3: USB disconnect, address 4
usb 4-3: new high speed USB device using ehci_hcd and address 5
usb 4-3: new device found, idVendor=13e0, idProduct=0151
usb 4-3: new device strings: Mfr=0, Product=2, SerialNumber=3
usb 4-3: Product: USB Mass Storage Device
usb 4-3: SerialNumber: 46060630000008
usb 4-3: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi 4:0:0:0: Direct-Access USB 2.0 Flash Drive 0.00 PQ: 0 ANSI: 2
sd 4:0:0:0: [sdc] 2015232 512-byte hardware sectors (1032 MB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 00 00 00 00
sd 4:0:0:0: [sdc] Assuming drive cache: write through
sd 4:0:0:0: [sdc] 2015232 512-byte hardware sectors (1032 MB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 00 00 00 00
sd 4:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 4:0:0:0: [sdc] Attached SCSI removable disk
sd 4:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
