A few months ago, I was trying to get a dual-stack client and server working  
on Windows 10. I was able to get the client and server to connect and fully 
work for ipv4, but I was unable to configure the network settings on the server 
so it would also work for ipv6. I tried several different approaches, but no 
matter what I tried, the server would not pass the ipv6 traffic. I decided to 
try again using a linux server. I configured a Ubuntu 16.04 LTS server running 
the latest version of openvpn from scratch. The server is behind a pfsense 
router with native dual stack. It has a single ethernet interface with ipv4 and 
ipv6 dhcp addresses. The client is behind a completely separate pfsense router. 
It also has native dual stack on a single ethernet interface with ipv4 and ipv6 
dhcp addresses. So as to not carry over any possible problems from the previous 
attempt, I created new keys and new configuration files from scratch. The 
client and server connect and the vpn will carry ipv4 traffic
 , but I'm not sure how to configure the server to carry the ipv6 traffic.

Note, I initially started using ULA addressing on the server (fc00::/64). That 
did not work, so I switched to prefix::/64. In both cases, everything worked 
properly except for passing ipv6 traffic.

I've tried to make the client and server configurations as minimalist as 
possible.

Here is the server configuration:

port 1194
proto udp
dev tun

ca /etc/openvpn/keys/ca.crt
cert /etc/openvpn/keys/server.crt
key /etc/openvpn/keys/server.key
dh /etc/openvpn/keys/dh4096.pem

cipher AES-256-CBC
auth SHA512

server 10.8.0.0 255.255.255.0
server-ipv6 {redacted prefix}::/64
push "redirect-gateway def1 bypass-dhcp"
push "redirect-gateway ipv6"
push "dhcp-option DNS 8.8.8.8"
push "dhcp-option DNS6 2001:4860:4860::8888"

ifconfig-pool-persist ipp.txt
keepalive 10 120
 
comp-lzo
 
persist-key
persist-tun
 
status openvpn-status.log
log openvpn.log
verb 3

Here is the client configuration:

ca ca.crt
cert client.crt
key client.key

remote {redacted ipv4 server address} 1194
comp-lzo
client
dev tun
redirect-gateway def1

remote-cert-tls server
cipher AES-256-CBC
auth SHA512
 
proto udp
resolv-retry infinite
nobind
 
persist-key
persist-tun
 
verb 3
mute 20

Are there any issues in the above configuration files?

I followed some instructions in a tutorial on digital ocean to configure the 
server firewall using ufw (which is a front-end to iptables). While I'm not 
exactly sure why or how it works, it works. I can ping the client and server 
using both ipv4 and ipv6 in both directions. I can look up ipv4 and ipv6 
addresses from the client using nslookup. I can ping external addresses and 
access external websites from the client using ipv4, but not using ipv6. As I 
said, I initially tried using fc00::/64 but that didn't work so I changed to 
{delegated prefix}::/64. That made no difference, so I'm not sure whether I 
should be using ULA or UGA. I'm quite sure the problems is at least in part 
because the firewall is not configured to pass the ipv6 traffic, but I haven't 
found any examples showing the ipv6 equivalent of how I configured the firewall 
for ipv4.

Forwarding of ipv4 and ipv6 is enabled.

Here are the rules I added to ufw for ipv4:

# START OPENVPN RULES
# NAT table rules
*nat
:POSTROUTING ACCEPT [0:0] 
# Allow traffic from OpenVPN client to wlp11s0 (change to the interface you 
discovered!)
-A POSTROUTING -s 10.8.0.0/8 -o wlp11s0 -j MASQUERADE
COMMIT
# END OPENVPN RULES

I tried posting on the forum. I received the usual RTFM replies, but no 
suggestions about ufw. The OpenVPN documentation and how-tos are sorely lacking 
for ipv6.

I'm hoping someone out there knows how to do this.


------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
_______________________________________________
Openvpn-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/openvpn-users

Reply via email to