Yes, I didn't mean to imply that this config was supported by openwisp but to point out that it would first have to be something possible in openwrt.
On Tue, Jul 23, 2019 at 11:25 AM M Ricky Anggoro P <[email protected]> wrote: > Thanks @2stacks for the advice. Giving your advice, High availability in > openWRT is for fail over Router. But it seems like OpenWISP is not support > yet for the configuration, CMIIW. After I search in this forum, I found > something similar, in this -> > https://groups.google.com/d/msg/openwisp/UpVgnZlwdOg/py06vwLtCQAJ > Federico said to only bridging LAN interface and wireless interface, but I > want different network between LAN and wireless, so I can remote the > OpenWRT from outside (No need VPN, because my organization already > established VPN to access the LAN Network). > > Pada Selasa, 23 Juli 2019 21.22.56 UTC+7, 2stacks menulis: >> >> Almost forgot, the wirless routers will have to be configured with "IP >> Helper" address to forward DHCP requests to the Raspi. You should be able >> to find examples for most of this in the Openwrt docs. >> >> https://openwrt.org/docs/guide-user/network/high-availability >> >> On Tue, Jul 23, 2019 at 10:20 AM A Stanley <[email protected]> wrote: >> >>> I think what you are asking is possible but I've never tried it. A few >>> things you'll have to get working. >>> >>> 1. DHCP server on they raspi (I would install a full server not dnsmasq) >>> 2. The Access Points will have to be configured as routers and not >>> bridges. >>> 3. Since you have two gateways on the same network you'll have to synch >>> your NAT and Default GW. >>> 4. You should be able to use keepalived to set up VRRP for your First >>> Hop Redundancy Protocol. >>> 5. You'll need to figure out a way to synchronize the NAT between the >>> two routers (I've only seen this done with Cisco Devices) >>> >>> I realize this isn't an answer so much as more things to think about. >>> >>> If it were me I'd put my wireless devices on their own vlan and separate >>> IP space and configure them as bridges. >>> >>> On Tue, Jul 23, 2019 at 9:42 AM M Ricky Anggoro P <[email protected]> >>> wrote: >>> >>>> Hello, this is my third time I ask for help in this forum, so I hope it >>>> solve my case >>>> So I want to established a Network like this: >>>> >>>> [image: Diagram.png] >>>> >>>> >>>> I Have OpenWISP2 Controller installed on my Raspberry Controller, that >>>> will control the Mikrotik-OpenWRT device. the Controller, and the Mikrotik >>>> OpenWRT device are on my organization network (10.33.109.0/24), and I >>>> want the wireless Network is different with the organization network, but >>>> the wireless Network on the OpenWRT 1 and OpenWRT 2 is same, and will get >>>> the DHCP service from the Raspberry Controller, not the OpenWRT device, and >>>> of course, it will need NAT. My question: >>>> >>>> - Is it possible for the wireless network to receive the Raspberry >>>> Controller and get NAT? >>>> >>>> - How to configure this to OpenWISP controller? >>>> >>>> >>>> I'm a little bit confused to configure this, and I heard I can use >>>> dnsmasq on Raspberry to build DHCP Server, but I dont know how to configure >>>> NAT from wireless Network to LAN (10.33.109.0/24) Network. >>>> >>>> >>>> >>>> Thank you very much >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "OpenWISP" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> To view this discussion on the web, visit >>>> https://groups.google.com/d/msgid/openwisp/fc542a50-9b71-4e56-9e6c-cd1a242aa369%40googlegroups.com >>>> <https://groups.google.com/d/msgid/openwisp/fc542a50-9b71-4e56-9e6c-cd1a242aa369%40googlegroups.com?utm_medium=email&utm_source=footer> >>>> . >>>> >>> -- > You received this message because you are subscribed to the Google Groups > "OpenWISP" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web, visit > https://groups.google.com/d/msgid/openwisp/016d3db3-0d08-4d69-b384-19561f3add1b%40googlegroups.com > <https://groups.google.com/d/msgid/openwisp/016d3db3-0d08-4d69-b384-19561f3add1b%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "OpenWISP" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web, visit https://groups.google.com/d/msgid/openwisp/CAP6YPdoXQEOhZtbczpVqY7ebgHJ-Q_4B-ug82gBXCxP3k-oHdA%40mail.gmail.com.
