This happens when the Configuration status has not been applied for more than 5 minutes, which should not happen if you are using openwisp-config correctly. What's the status shown in the configuration tab?
F. On Thu, Aug 5, 2021 at 9:27 AM HÒA TRẦN VĂN <[email protected]> wrote: > Thanks for your detailed instructions. > > I have installed and directly connected OpenVPN. Now I have seen the > management ip appear. > > But now the health status changed to problem because the Configuration > Applied check failed as shown below, even though I was able to configure > the device (access point) from openwisp controller successfully. > > Can you explain to me why not and how I have to fix it. Thank you so much > > [image: health_status.png] > > Vào lúc 04:36:06 UTC+7 ngày Thứ Năm, 5 tháng 8, 2021, f.capoano đã viết: > >> Hi, >> >> By default OpenWISP Monitoring >> <https://github.com/openwisp/openwisp-monitoring> is configured to send >> ping checks on the management interface only, if ping fails or if the >> management interface is not set the health status is set to critical. >> >> If you want the status to be OK without modifying the default settings, >> you have to ensure that the "management_interface" configuration option >> of the openwisp-config OpenWRT agent >> <https://github.com/openwisp/openwisp-config/#configuration-options> (in >> /etc/config/openwisp) is set to be an interface which OpenWISP can reach, >> for example, a management VPN tunnel, a VLAN or the LAN interface if >> OpenWISP is deployed in the same L2 network where the device is located. >> >> For example, in many installations I use a tun OpenVPN interface for >> management, OpenWISP is deployed on the internet and can reach the devices >> via the OpenVPN tunnel tun0, in /etc/config/openwisp I have: >> >> option management_interface 'tun0' >> >> Alternatively, if you have deployed OpenWISP locally in the same L2 >> network where devices are located, you can set: >> >> OPENWISP_MONITORING_MANAGEMENT_IP_ONLY = False >> >> in the django settings.py and restart OpenWISP with "supervisorctl >> restart all". >> More about this setting in the README of OpenWISP Monitoring: >> https://github.com/openwisp/openwisp-monitoring#openwisp-monitoring-management-ip-only >> . >> >> I hope this helps! >> >> Thanks for writing this question here. >> Best regards >> Federico Capoano >> >> On Tue, Aug 3, 2021 at 11:48 AM HÒA TRẦN VĂN <[email protected]> wrote: >> >>> The access point successfully connects to openwisp and i can change its >>> configuration at any time, but the health status is always critical. Can >>> you help me get the right health status of the access point. Thank you very >>> much. >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "OpenWISP" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web, visit >>> https://groups.google.com/d/msgid/openwisp/95d85e8c-80f9-42b6-888e-ffd4a5fe6855n%40googlegroups.com >>> <https://groups.google.com/d/msgid/openwisp/95d85e8c-80f9-42b6-888e-ffd4a5fe6855n%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >> -- > You received this message because you are subscribed to the Google Groups > "OpenWISP" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web, visit > https://groups.google.com/d/msgid/openwisp/2a838fdd-23ac-40d3-8887-b2a0b4afabecn%40googlegroups.com > <https://groups.google.com/d/msgid/openwisp/2a838fdd-23ac-40d3-8887-b2a0b4afabecn%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "OpenWISP" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web, visit https://groups.google.com/d/msgid/openwisp/CAAGgX6Ls%3Dys3ctcomf2F2j%2BCTvBr4%3DXf14NszopARhQ%3DqFrL7w%40mail.gmail.com.
