OK. I just tried something silly. Instead of deleting and re-creating the
radio config completely, I changed radio1 to 802.11g, saved, waited for the
config to propagate to the APs, changed it back to 802.11n, saved, waited
for the config to propagate. Now I was able to edit the device config (add
the map/location information), save, and no validation error! JSON output
of the template still looks good.
{
"radios": [
{
"protocol": "802.11ac",
"name": "radio0",
"phy": "",
"channel": 0,
"channel_width": 80,
"country": "US",
"disabled": false,
"driver": "mac80211",
"hwmode": "11a"
},
{
"protocol": "802.11n",
"name": "radio1",
"phy": "",
"channel": 0,
"channel_width": 20,
"tx_power": 20,
"country": "US",
"disabled": false,
"driver": "mac80211",
"hwmode": "11g"
}
]
}
On Monday, September 12, 2022 at 11:29:38 AM UTC-7 [email protected] wrote:
> Thanks for the quick responses, Federico and Martin!
>
> Federico, you asked: Is this only a template or do you have it in many
> places? It is only defined in once place. It is a single template that
> is simply for defining the radios.
>
> Martin, you asked:
>
> 1) Are you changing a device's configuration or a template? This is a
> great question. This is happening when I am editing a device's
> configuration. I was adding location information to a device and upon
> saving I would get the validation error per my original post. I have not
> yet created/modified any templates since the upgrade.
>
> 2) Could you please click on 'Advanced Mode (JSON)' (on the Right side of
> where you configured the radios, somewhat down from the top but not at the
> bottom) and send that JSON ?
>
> That would make your configuration a lot clearer than the two
> screenshots. Absolutely! See below.
>
> {
> "radios": [
> {
> "protocol": "802.11ac",
> "name": "radio0",
> "phy": "",
> "channel": 0,
> "channel_width": 80,
> "country": "US",
> "disabled": false,
> "driver": "mac80211",
> "hwmode": "11a"
> },
> {
> "protocol": "802.11n",
>
>
> "name": "radio1",
> "phy": "",
> "channel": 0,
> "channel_width": 20,
> "tx_power": 20,
> "country": "US",
>
> "disabled": false,
>
>
> "driver": "mac80211",
> "hwmode": "11g"
> }
>
> ]
> }
>
> 3) Can you entirely delete the Radios and save the configuration, then
> re-create the Radios step-by-step and save in between? Error happens
> again? I have not tried this yet, but per Federico's response as well as
> yours, this sounds like it may be what I need to do. However, given the
> JSON output from above, I'm wondering if it's possible to re-push the radio
> config? It appears to be correct template wise.
> On Monday, September 12, 2022 at 8:23:46 AM UTC-7 Martin Süfke wrote:
>
>> Hello Anthony,
>>
>> I have a recent-ish OpenWISP install (installed by Ansible) and I tried
>> replicating your problem - no success. My Radios are saved smoothly when
>> created as a device configuration.
>> However once saved, my "radio config" does not show the settings for
>> "channel width (mhz)" and "country" which I set for the 5GHz Radio to 80MHz
>> (VHT80 Mode) and US like you showed, so error, too, but different.
>>
>> Questions:
>> 1) Are you changing a device's configuration or a template?
>>
>> 2) Could you please click on 'Advanced Mode (JSON)' (on the Right side of
>> where you configured the radios, somewhat down from the top but not at the
>> bottom) and send that JSON ?
>> That would make your configuration a lot clearer than the two screenshots.
>>
>> 3) Can you entirely delete the Radios and save the configuration, then
>> re-create the Radios step-by-step and save in between? Error happens again?
>>
>> -Martin
>> On 12.09.22 16:58, '[email protected]' via OpenWISP wrote:
>>
>> Hello!
>>
>> Yesterday I upgraded to OpenWISP 22.05 via Ansible and the upgrade seemed
>> to be successful. However, I'm running into an issue with some
>> configuration failing validation and could use some pointers on
>> troubleshooting.
>>
>> Whenever I try to save config changes, it complains about the following:
>>
>> Invalid configuration triggered by "#/radios/1", validator says:
>>
>> {'protocol': '802.11ac', 'name': 'radio1', 'phy': '', 'channel': 0,
>> 'channel_width': 20, 'tx_power': 20, 'country': 'US', 'disabled': False,
>> 'driver': 'mac80211', 'hwmode': '11g'} is not valid under any of the given
>> schemas
>>
>> Here's how the radio configuration looks via the UI: …
>>
>> <snip> cut short </snap>
>>
>>
>>
--
You received this message because you are subscribed to the Google Groups
"OpenWISP" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web, visit
https://groups.google.com/d/msgid/openwisp/3f107a9b-4c75-41a0-8b06-d235a2f0dd74n%40googlegroups.com.
