Author: wigyori Date: 2014-12-12 12:43:56 +0100 (Fri, 12 Dec 2014) New Revision: 43649
Modified: trunk/target/linux/mxs/files/arch/arm/boot/dts/imx28-duckbill.dts Log: mxs: update dts file for Duckbill Signed-off-by: Michael Heimpold <[email protected]> Modified: trunk/target/linux/mxs/files/arch/arm/boot/dts/imx28-duckbill.dts =================================================================== --- trunk/target/linux/mxs/files/arch/arm/boot/dts/imx28-duckbill.dts 2014-12-12 11:39:22 UTC (rev 43648) +++ trunk/target/linux/mxs/files/arch/arm/boot/dts/imx28-duckbill.dts 2014-12-12 11:43:56 UTC (rev 43649) @@ -1,5 +1,5 @@ /* - * Copyright (C) 2013 Michael Heimpold <[email protected]> + * Copyright (C) 2013-2014 Michael Heimpold <[email protected]> * * The code contained herein is licensed under the GNU General Public * License. You may obtain a copy of the GNU General Public License @@ -25,13 +25,28 @@ ssp0: ssp@80010000 { compatible = "fsl,imx28-mmc"; pinctrl-names = "default"; - pinctrl-0 = <&mmc0_8bit_pins_a + pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_cd_cfg &mmc0_sck_cfg>; - bus-width = <8>; + bus-width = <4>; vmmc-supply = <®_3p3v>; status = "okay"; }; + ssp2: ssp@80014000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; + + spidev: spidev@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + pinctrl@80018000 { pinctrl-names = "default"; pinctrl-0 = <&hog_pins_a>; @@ -39,27 +54,33 @@ hog_pins_a: hog@0 { reg = <0>; fsl,pinmux-ids = < - 0x40d3 /* MX28_PAD_ENET0_RX_CLK__GPIO_4_13, PHY Reset */ + MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */ >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; led_pins_a: led_gpio@0 { reg = <0>; fsl,pinmux-ids = < - 0x3043 /* MX28_PAD_AUART1_RX__GPIO_3_4 */ - 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + MX28_PAD_AUART1_RX__GPIO_3_4 + MX28_PAD_AUART1_TX__GPIO_3_5 >; - fsl,drive-strength = <0>; - fsl,voltage = <1>; - fsl,pull-up = <0>; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; }; }; }; apbx@80040000 { + i2c0: i2c@80058000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + }; + duart: serial@80074000 { pinctrl-names = "default"; pinctrl-0 = <&duart_pins_a>; @@ -82,7 +103,7 @@ pinctrl-names = "default"; pinctrl-0 = <&mac0_pins_a>; phy-supply = <®_3p3v>; - phy-reset-gpios = <&gpio4 13 0>; + phy-reset-gpios = <&gpio2 7 1>; phy-reset-duration = <100>; status = "okay"; }; _______________________________________________ openwrt-commits mailing list [email protected] https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-commits
