Hi Karthik,
I just try to change lan option proto.
The conf is as below:
config interface loopback
option ifname lo
option proto static
option ipaddr 127.0.0.1
option netmask 255.0.0.0
config interface lan
option ifname eth0
option proto bridge
option ipaddr '192.168.8.180'
option netmask 255.255.255.0
config interface wan
option ifname eth1
option proto dhcp
the result of ifconfig command:
eth0 Link encap:Ethernet HWaddr 00:01:C1:00:42:80
inet addr:192.168.8.188 Bcast:192.168.8.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:112374 errors:0 dropped:0 overruns:0 frame:0
TX packets:892 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:9910188 (9.4 MiB) TX bytes:154740 (151.1 KiB)
eth1 Link encap:Ethernet HWaddr 00:01:C1:00:42:81
inet addr:192.168.7.188 Bcast:192.168.7.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:197 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:63040 (61.5 KiB)
fp Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP RUNNING MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:178 errors:0 dropped:0 overruns:0 frame:0
TX packets:178 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:27024 (26.3 KiB) TX bytes:27024 (26.3 KiB)
Thanks,
Best Regards,
Gary
_____
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Karthik
Venkateswaran
Sent: Monday, August 04, 2008 8:18 PM
To: OpenWrt Development List
Subject: Re: [OpenWrt-Devel] how to briding lan and wan
Can you cut and paste your /etc/config/network and ifconfig to give more
clarity.
Cheers,
Karthik Venkateswaran
"Gary Li" <[EMAIL PROTECTED]>
Sent by: [EMAIL PROTECTED]
08/04/2008 05:11 PM
Please respond to
OpenWrt Development List <[email protected]>
To
<[email protected]>
cc
Subject
[OpenWrt-Devel] how to briding lan and wan
Hi all,
When I try to modify configuration to support brige in the
etc/config/netwok.
And execute network restart.
I got a error:
Interface type bridge not supported.
Anyone know how to do that?
Thanks,
Best regards,
Gary
____________________________________________________________________________
_________________________________________
openwrt-devel mailing list
[email protected]
http://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
______________________________________________________________________
_______________________________________________
openwrt-devel mailing list
[email protected]
http://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
