I would have to say that my address are setup correctly why would move the toolchain out of the my build would change the Ramdisk?
This is the follow steps i took to see what was wrong Note: External Toolchain is the openwrt toolchain moved outside. 1) Using External Toolchain, make kernel and ramdisk fail to boot ram disk 2) Using Internal Toolchain to build kernel and external ramdisk fail to boot 3) Using Internal Toolchain to build kernel and internal toolchain ramdisk , boots fine. So what would cause /etc/preinit to to boot? maybe busybox is being compiled wrong? On Mon, Mar 22, 2010 at 5:00 AM, Florian Fainelli <[email protected]> wrote: > On Monday 22 March 2010 01:54:28 Pawel Pastuszak wrote: >> Thanks for pointing me to the thread after reading the thread about >> "Compiling outside of buildroot" I was able to make and image. >> >> But now the problem that i am having is that the image is not booting >> the ramdisk which is an ext2 its compile about /etc/preinit fail but >> when i uses my older ramdisk image very thing is good. Any Ideas? > > Check that your kernel has support for initrd and ext2 filesystem, that should > do it. Also check that you correctly set the initrd start address and size. > >> >> On Mon, Mar 15, 2010 at 5:05 AM, Bas Mevissen <[email protected]> wrote: >> > On Sat, 2010-03-13 at 22:22 -0500, Pawel Pastuszak wrote: >> >> Hi All, >> >> >> >> I am trying to split the toolchain out of my main openwrt build, after >> >> generating the toolchain i moved it to a new location from >> >> staging_dir/toolchain-powerpc_gcc-4.3.3_glibc-2.7 and set up and new >> >> build that points to the toolchain. >> >> >> >> I am using Revision: 20023. >> >> >> >> Is there any think that I am missing? >> >> >> >> >> >> powerpc-openwrt-linux-gnu-gcc -Os -pipe -funit-at-a-time -mcpu=405 >> >> -msoft-float -Wall -Wunused -I./include/linux/include/ -Iinclude/ >> >> -DARPTABLES_VERSION=\"0.0.3-3\" -o arptables arptables-standalone.o >> >> arptables.o libarptc/libarptc.o extensions/arpt_standard.o >> >> extensions/arpt_mangle.o >> >> /development/external_toolchain_test/usr/bin/../lib/gcc/powerpc-openwrt- >> >>linux-gnu/4.3.3/../../../../powerpc-openwrt-linux-gnu/bin/ld: cannot find >> >> -lgcc_s >> >> collect2: ld returned 1 exit status >> >> make[4]: *** [arptables] Error 1 >> >> make[4]: Leaving directory >> >> `/development/openwrt/build_dir/target-powerpc-openwrt-linux-gnu/arptabl >> >>es-v0.0.3-3' make[3]: *** >> >> [/development/openwrt/build_dir/target-powerpc-openwrt-linux-gnu/arptabl >> >>es-v0.0.3-3/.built] Error 2 >> >> make[3]: Leaving directory `/development/openwrt/package/arptables' >> >> make[2]: *** [package/arptables/compile] Error 2 >> >> make[2]: Leaving directory `/development/openwrt' >> > >> > Looks like a relocation problem. In general, gcc has a hard coded >> > absolute path to some libraries. Solution is to compile the cross >> > compiler for your new destination path or fix the binary. >> > >> > This has been discussed quite recently here in the "Compiling outside of >> > buildroot" thread. >> > >> > Bas. >> > >> > >> > _______________________________________________ >> > openwrt-devel mailing list >> > [email protected] >> > https://lists.openwrt.org/mailman/listinfo/openwrt-devel >> >> _______________________________________________ >> openwrt-devel mailing list >> [email protected] >> https://lists.openwrt.org/mailman/listinfo/openwrt-devel >> > _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
