Hi,
The OpenWrt Team is pleased to announce the third and last release
candidate (RC3) of the next stable release, codenamed Backfire. Testing
of this build will help refine the code in preparation of the final
release.
I have tested usb support for the ASUS WL-500gP V2 today, but no
success with brcm-2.4 and brcm47xx.
In addition to the software included into the squashfs-image, I have
installed following packages
pciutils
usbutils
kmod-usb2
kmod-usb-serial-pl2303
I have attached some output from opkg, lspci, lsusb and dmesg for
brcm47xx target. It looks like, that the loading of the usb modules fail
(unknown symbols).
Sorry for bad news....
Micha
Linux version 2.6.32.10 ([email protected]) (gcc version 4.3.3 (GCC) )
#10 Fri Apr 2 18:53:05 CEST 2010
CPU revision is: 00029029 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x14, vendor 0x4243)
ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x08, vendor 0x4243)
ssb: Core 3 found: USB 2.0 Host (cc 0x819, rev 0x02, vendor 0x4243)
ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x04, vendor 0x4243)
ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x0D, vendor 0x4243)
ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
ssb: Found rev 0 PMU (capabilities 0x04A63400)
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0806, irq 4 => 4
ssb: set_irq: core 0x0816, irq 5 => 2
ssb: set_irq: core 0x0812, irq 2 => 5
ssb: after irq reconfiguration
ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
ssb: core 0x0819, irq : 2(S) 3 4 5 6* D I
ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
ssb: core 0x0812, irq : 2(S) 3 4 5* 6 D I
ssb: core 0x081c, irq : 2(S) 3 4 5 6 D I*
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
On node 0 totalpages: 8192
free_area_init_node: node 0, pgdat 8029e7d0, node_mem_map 81000000
Normal zone: 64 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 8128 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd
console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29524k/32768k available (2322k kernel code, 3244k reserved, 357k data,
136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 239.10 BogoMIPS (lpj=478208)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x800000 at 0x1fc00000
bootloader size: 131072
Updating TRX offsets and length:
old trx = [0x0000001c, 0x00000974, 0x000da400], len=0x002d1000 crc32=0x0d76435b
new trx = [0x0000001c, 0x00000974, 0x000da400], len=0x000da400 crc32=0xcd527507
Done
Creating 4 MTD partitions on "Physically mapped flash":
0x000000000000-0x000000020000 : "cfe"
0x000000020000-0x0000007f0000 : "linux"
0x0000000fa400-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be
smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2D0000, len=520000
0x0000002d0000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "nvram"
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:22:15:26:a6:e5
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
diag: Detected 'ASUS WL-500g Premium V2'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found a 5325! It's a 5350.
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
b44: eth0: powering down PHY
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering forwarding state
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
b43-phy0: Broadcom 5354 WLAN found (core revision 13)
phy0: Selected rate control algorithm 'minstrel'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (463 buckets, 1852 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
usbcore: Unknown symbol utf16s_to_utf8s
ehci_hcd: Unknown symbol usb_hcd_pci_probe
ehci_hcd: Unknown symbol usb_hcd_unlink_urb_from_ep
ehci_hcd: Unknown symbol usb_disabled
ehci_hcd: Unknown symbol usb_hcd_check_unlink_urb
ehci_hcd: Unknown symbol usb_hcds_loaded
ehci_hcd: Unknown symbol usb_calc_bus_time
ehci_hcd: Unknown symbol ehci_cf_port_reset_rwsem
ehci_hcd: Unknown symbol usb_hcd_pci_shutdown
ehci_hcd: Unknown symbol usb_hcd_link_urb_to_ep
ehci_hcd: Unknown symbol usb_put_hcd
ehci_hcd: Unknown symbol usb_hub_clear_tt_buffer
ehci_hcd: Unknown symbol usb_hcd_giveback_urb
ehci_hcd: Unknown symbol usb_hcd_poll_rh_status
ehci_hcd: Unknown symbol usb_create_hcd
ehci_hcd: Unknown symbol usb_hcd_pci_remove
ehci_hcd: Unknown symbol usb_remove_hcd
ehci_hcd: Unknown symbol usb_add_hcd
pl2303: Unknown symbol usb_serial_port_softint
pl2303: Unknown symbol usb_register_driver
pl2303: Unknown symbol usb_serial_handle_sysrq_char
pl2303: Unknown symbol usb_clear_halt
pl2303: Unknown symbol usb_serial_disconnect
pl2303: Unknown symbol usb_submit_urb
pl2303: Unknown symbol usb_serial_suspend
pl2303: Unknown symbol usb_control_msg
pl2303: Unknown symbol usb_deregister
pl2303: Unknown symbol usb_serial_handle_break
pl2303: Unknown symbol usb_kill_urb
pl2303: Unknown symbol usb_serial_probe
pl2303: Unknown symbol usb_serial_register
pl2303: Unknown symbol usb_serial_deregister
pl2303: Unknown symbol usb_serial_resume
usbserial: Unknown symbol usb_alloc_urb
usbserial: Unknown symbol usb_free_urb
usbserial: Unknown symbol usb_register_driver
usbserial: Unknown symbol usb_match_one_id
usbserial: Unknown symbol usb_disabled
usbserial: Unknown symbol usb_put_dev
usbserial: Unknown symbol usb_get_dev
usbserial: Unknown symbol usb_submit_urb
usbserial: Unknown symbol usb_match_id
usbserial: Unknown symbol usb_store_new_id
usbserial: Unknown symbol usb_control_msg
usbserial: Unknown symbol usb_deregister
usbserial: Unknown symbol usb_kill_urb
base-files - 41-r20653
busybox - 1.15.3-1
crda - 1.1.0-2
dnsmasq - 2.52-1
dropbear - 0.52-4
firewall - 1-10
hotplug2 - 1.0-beta-1
iptables - 1.4.6-2
iptables-mod-conntrack - 1.4.6-2
iptables-mod-nat - 1.4.6-2
iw - 0.9.19-1
kernel - 2.6.32.10-1
kmod-b43 - 2.6.32.10+2010-03-24-5
kmod-b43legacy - 2.6.32.10+2010-03-24-5
kmod-cfg80211 - 2.6.32.10+2010-03-24-5
kmod-crc-ccitt - 2.6.32.10-1
kmod-crypto-aes - 2.6.32.10-1
kmod-crypto-arc4 - 2.6.32.10-1
kmod-crypto-core - 2.6.32.10-1
kmod-diag - 2.6.32.10-6
kmod-ipt-conntrack - 2.6.32.10-1
kmod-ipt-core - 2.6.32.10-1
kmod-ipt-nat - 2.6.32.10-1
kmod-ipt-nathelper - 2.6.32.10-1
kmod-mac80211 - 2.6.32.10+2010-03-24-5
kmod-nls-base - 2.6.32.10-1
kmod-ppp - 2.6.32.10-1
kmod-pppoe - 2.6.32.10-1
kmod-switch - 2.6.32.10-2
kmod-usb-core - 2.6.32.10-1
kmod-usb-serial - 2.6.32.10-1
kmod-usb-serial-pl2303 - 2.6.32.10-1
kmod-usb2 - 2.6.32.10-1
libc - 0.9.30.1-41
libgcc - 4.3.3+cs-41
libiptc - 1.4.6-2
liblua - 5.1.4-6
libnl-tiny - 0.1-1
libuci - 12012009.5-1
libuci-lua - 12012009.5-1
libusb - 0.1.12-2
libxtables - 1.4.6-2
lua - 5.1.4-6
luci - 0.9+svn5992-1
luci-admin-core - 0.9+svn5992-1
luci-admin-full - 0.9+svn5992-1
luci-admin-mini - 0.9+svn5992-1
luci-app-firewall - 0.9+svn5992-1
luci-app-initmgr - 0.9+svn5992-1
luci-cbi - 0.9+svn5992-1
luci-core - 0.9+svn5992-1
luci-http - 0.9+svn5992-1
luci-i18n-english - 0.9+svn5992-1
luci-ipkg - 0.9+svn5992-1
luci-lmo - 0.9+svn5992-1
luci-nixio - 0.9+svn5992-1
luci-sgi-cgi - 0.9+svn5992-1
luci-sys - 0.9+svn5992-1
luci-theme-base - 0.9+svn5992-1
luci-theme-openwrt - 0.9+svn5992-1
luci-uci - 0.9+svn5992-1
luci-uvl - 0.9+svn5992-1
luci-web - 0.9+svn5992-1
mtd - 12
nvram - 5
opkg - 513-1
pciutils - 3.1.7-1
ppp - 2.4.4-5
ppp-mod-pppoe - 2.4.4-5
uci - 12012009.5-1
udevtrigger - 106-1
uhttpd - 6
usbutils - 0.86-1
wireless-tools - 29-4
wpad-mini - 20100309-1
zlib - 1.2.3-5
_______________________________________________
openwrt-devel mailing list
[email protected]
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
