ouch, none of these have a signed-off-by line and i noticed only after
pushing :(
On 10/03/2016 07:31, alzhao wrote:
> This patches adds support for GL-MT300A.
> GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
> Two LANs, USB, UART and MMC daughter board.
> ---
> target/linux/ramips/base-files/etc/board.d/01_leds | 3 +
> .../linux/ramips/base-files/etc/board.d/02_network | 1 +
> target/linux/ramips/base-files/lib/ramips.sh | 3 +
> .../ramips/base-files/lib/upgrade/platform.sh | 1 +
> target/linux/ramips/dts/GL-MT300A.dts | 164
> +++++++++++++++++++++
> target/linux/ramips/image/Makefile | 2 +
> target/linux/ramips/mt7620/profiles/gli.mk | 16 ++
> 7 files changed, 190 insertions(+)
> create mode 100644 target/linux/ramips/dts/GL-MT300A.dts
> create mode 100644 target/linux/ramips/mt7620/profiles/gli.mk
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
> b/target/linux/ramips/base-files/etc/board.d/01_leds
> index 8fd50fe..536a363 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -137,6 +137,9 @@ fonera20n)
> set_usb_led "$board:orange:usb"
> set_wifi_led "$board:orange:wifi"
> ;;
> +gl-mt300a)
> + set_wifi_led "$board:wlan"
> + ;;
> hc5661)
> ucidef_set_led_default "system" "system" "$board:blue:system" "1"
> ucidef_set_led_netdev "internet" "internet" "$board:blue:internet"
> "eth0.2"
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
> b/target/linux/ramips/base-files/etc/board.d/02_network
> index ac5a312..74599ad 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -113,6 +113,7 @@ ramips_setup_interfaces()
> dir-860l-b1|\
> f5d8235-v1|\
> f5d8235-v2|\
> + gl-mt300a|\
> hg255d|\
> mzk-wdpr|\
> jhr-n805r|\
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh
> b/target/linux/ramips/base-files/lib/ramips.sh
> index 3fdb562..ba27c14 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -175,6 +175,9 @@ ramips_board_detect() {
> *"FreeStation5")
> name="freestation5"
> ;;
> + *"GL-MT300A")
> + name="gl-mt300a"
> + ;;
> *"HC5661")
> name="hc5661"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index e01f9ce..876416e 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -56,6 +56,7 @@ platform_check_image() {
> firewrt|\
> fonera20n|\
> freestation5|\
> + gl-mt300a|\
> hc5*61|\
> hg255d|\
> hlk-rm04|\
> diff --git a/target/linux/ramips/dts/GL-MT300A.dts
> b/target/linux/ramips/dts/GL-MT300A.dts
> new file mode 100644
> index 0000000..c1eb0a9
> --- /dev/null
> +++ b/target/linux/ramips/dts/GL-MT300A.dts
> @@ -0,0 +1,164 @@
> +/dts-v1/;
> +
> +/include/ "mt7620a.dtsi"
> +
> +/ {
> + compatible = "GL-MT300A", "ralink,mt7620a-soc";
> + model = "GL-MT300A";
> +
> + chosen {
> + bootargs = "console=ttyS0,115200";
> + };
> +
> + palmbus@10000000 {
> + gpio0: gpio@600 {
> + status = "okay";
> + };
> +
> + gpio1: gpio@638 {
> + status = "okay";
> + };
> +
> + gpio2: gpio@660 {
> + status = "okay";
> + };
> +
> + gpio3: gpio@688 {
> + status = "okay";
> + };
> +
> + spi@b00 {
> + status = "okay";
> +
> + m25p80@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "w25q128";
> + reg = <0 0>;
> + linux,modalias = "m25p80", "w25q128";
> + spi-max-frequency = <10000000>;
> +
> + partition@0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + };
> +
> + partition@30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition@40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + partition@50000 {
> + label = "firmware";
> + reg = <0x50000 0xf80000>;
> + };
> +
> + partition@ff0000 {
> + label = "art";
> + reg = <0xff0000 0x10000>;
> + };
> + };
> + };
> + };
> +
> + sdhci@10130000 {
> + status = "okay";
> + };
> +
> + ehci@101c0000 {
> + status = "okay";
> + };
> +
> + ohci@101c1000 {
> + status = "okay";
> + };
> +
> + ethernet@10100000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ephy_pins>;
> + mtd-mac-address = <&factory 0x4000>;
> + ralink,port-map = "wllll";
> + };
> +
> + wmac@10180000 {
> + ralink,mtd-eeprom = <&factory 0>;
> + };
> +
> + pcie@10140000 {
> + status = "okay";
> +
> + pcie-bridge {
> + mt76@0,0 {
> + reg = <0x0000 0 0 0 0>;
> + device_type = "pci";
> + mediatek,mtd-eeprom = <&factory 0x8000>;
> + mediatek,2ghz = <0>;
> + };
> + };
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + gpio {
> + ralink,group = "wled","ephy","uartf","i2c";
> + ralink,function = "gpio";
> + };
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + wan {
> + label = "gl-mt300a:wan";
> + gpios = <&gpio2 0 1>;
> + };
> +
> + lan {
> + label = "gl-mt300a:lan";
> + gpios = <&gpio2 1 1>;
> + };
> +
> + wlan {
> + label = "gl-mt300a:wlan";
> + gpios = <&gpio3 0 1>;
> + };
> +
> + usb {
> + label = "gl-mt300a:usb";
> + gpios = <&gpio0 7 1>;
> + };
> +
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
> + reset {
> + label = "reset";
> + gpios = <&gpio0 13 1>;
> + linux,code = <0x198>;
> + };
> +
> + BTN_0 {
> + label = "BTN_0";
> + gpios = <&gpio0 1 1>;
> + linux,code = <0x100>;
> + };
> +
> + BTN_1 {
> + label = "BTN_1";
> + gpios = <&gpio0 2 1>;
> + linux,code = <0x101>;
> + };
> + };
> +};
> diff --git a/target/linux/ramips/image/Makefile
> b/target/linux/ramips/image/Makefile
> index e85c574..fb7407b 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -993,6 +993,7 @@ Image/Build/Profile/RT-N14U=$(call
> BuildFirmware/Default8M/$(1),$(1),rt-n14u,RT-
> Image/Build/Profile/WRTNODE=$(call
> BuildFirmware/Default16M/$(1),$(1),wrtnode,WRTNODE)
> Image/Build/Profile/WT3020=$(call
> BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
> Image/Build/Profile/MIWIFI-MINI=$(call
> BuildFirmware/Default16M/$(1),$(1),miwifi-mini,MIWIFI-MINI)
> +Image/Build/Profile/GL-MT300A=$(call
> BuildFirmware/Default16M/$(1),$(1),gl-mt300a,GL-MT300A)
> Image/Build/Profile/ZTE-Q7=$(call
> BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
> Image/Build/Profile/YOUKU-YK1=$(call
> BuildFirmware/Default16M/$(1),$(1),youku-yk1,YOUKU-YK1)
> Image/Build/Profile/ZBT-WA05=$(call
> BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
> @@ -1036,6 +1037,7 @@ define Image/Build/Profile/Default
> $(call Image/Build/Profile/WRTNODE,$(1))
> $(call Image/Build/Profile/WT3020,$(1))
> $(call Image/Build/Profile/MIWIFI-MINI,$(1))
> + $(call Image/Build/Profile/GL-MT300A,$(1))
> $(call Image/Build/Profile/ZTE-Q7,$(1))
> $(call Image/Build/Profile/YOUKU-YK1,$(1))
> $(call Image/Build/Profile/ZBT-WA05,$(1))
> diff --git a/target/linux/ramips/mt7620/profiles/gli.mk
> b/target/linux/ramips/mt7620/profiles/gli.mk
> new file mode 100644
> index 0000000..53e2e9d
> --- /dev/null
> +++ b/target/linux/ramips/mt7620/profiles/gli.mk
> @@ -0,0 +1,16 @@
> +#
> +# Copyright (C) 2015 OpenWrt.org
> +#
> +# This is free software, licensed under the GNU General Public License v2.
> +# See /LICENSE for more information.
> +#
> +
> +define Profile/GL-MT300A
> + NAME:=GL-MT300A
> + PACKAGES:=kmod-usb-core kmod-usb-dwc2 kmod-usb2 kmod-usb-ohci kmod-mt76
> +endef
> +
> +define Profile/GL-MT300A/Description
> + Support for gl-mt300a Router
> +endef
> +$(eval $(call Profile,GL-MT300A))
>
_______________________________________________
openwrt-devel mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
