CS-QR10 is MT7620A based IP Camera.
the camera and sound does not work with kernel 4.4.
- camera chip is sn9c291.
- sound chip is wm8960.
Signed-off-by: YuheiOKAWA <tochiro.srch...@gmail.com>
---
target/linux/ramips/base-files/etc/board.d/01_leds | 3 +-
.../linux/ramips/base-files/etc/board.d/02_network | 1 +
target/linux/ramips/base-files/etc/diag.sh | 1 +
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/CS-QR10.dts | 163 +++++++++++++++++++++
target/linux/ramips/image/mt7620.mk | 2 +
target/linux/ramips/mt7620/profiles/planex.mk | 19 +++
8 files changed, 192 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ramips/dts/CS-QR10.dts
create mode 100644 target/linux/ramips/mt7620/profiles/planex.mk
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
b/target/linux/ramips/base-files/etc/board.d/01_leds
index 5816e60..e319f36 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -30,7 +30,8 @@ br-6475nd|\
mzk-w300nh2)
set_wifi_led "$board:amber:wlan"
;;
-a5-v11)
+a5-v11|\
+cs-qr10)
ucidef_set_led_default "power" "POWER" "$board:red:power" "1"
;;
ai-br100)
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
b/target/linux/ramips/base-files/etc/board.d/02_network
index 4b65d36..416b13c 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -159,6 +159,7 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9@eth0"
;;
+ cs-qr10|\
d105|\
hpm|\
na930|\
diff --git a/target/linux/ramips/base-files/etc/diag.sh
b/target/linux/ramips/base-files/etc/diag.sh
index daa7fb1..233d15c 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -32,6 +32,7 @@ get_status_led() {
status_led="$board:green:power"
;;
a5-v11|\
+ cs-qr10|\
d105|\
dcs-930l-b1|\
ex2700|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh
b/target/linux/ramips/base-files/lib/ramips.sh
index 5f1df7b..2df2591 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -88,6 +88,9 @@ ramips_board_detect() {
*"CF-WR800N")
name="cf-wr800n"
;;
+ *"CS-QR10")
+ name="cs-qr10"
+ ;;
*"CY-SWR1100")
name="cy-swr1100"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index c329dce..af7fb12 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -34,6 +34,7 @@ platform_check_image() {
broadway|\
carambola|\
cf-wr800n|\
+ cs-qr10|\
d105|\
dap-1350|\
db-wrt01|\
diff --git a/target/linux/ramips/dts/CS-QR10.dts
b/target/linux/ramips/dts/CS-QR10.dts
new file mode 100644
index 0000000..08299e3
--- /dev/null
+++ b/target/linux/ramips/dts/CS-QR10.dts
@@ -0,0 +1,163 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+ compatible = "ralink,mt7620a-soc";
+ model = "Planex CS-QR10";
+
+ palmbus@10000000 {
+ gpio0: gpio@600 {
+ status = "okay";
+ };
+
+ gpio1: gpio@638 {
+ status = "okay";
+ };
+
+ gpio2: gpio@660 {
+ status = "okay";
+ };
+
+ gpio3: gpio@688 {
+ status = "okay";
+ };
+
+ i2c@900 {
+ status = "okay";
+ };
+
+ i2s: i2s@a00 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcm_i2s_pins>;
+ };
+
+ spi@b00 {
+ status = "okay";
+
+ m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0 0>;
+ linux,modalias = "m25p80", "mx25l6405d";
+ spi-max-frequency = <10000000>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition@40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition@50000 {
+ label = "firmware";
+ reg = <0x50000 0x7b0000>;
+ };
+ };
+ };
+
+ pcm@2000 {
+ status = "okay";
+ };
+
+ gdma@2800 {
+ status = "okay";
+ };
+ };
+
+ pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "spi refclk", "rgmii1";
+ ralink,function = "gpio";
+ };
+ wdt {
+ ralink,group = "wdt";
+ ralink,function = "wdt refclk";
+ };
+ };
+ };
+
+ ethernet@10100000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ephy_pins>;
+ mtd-mac-address = <&factory 0x4>;
+ mediatek,portmap = "llllw";
+ };
+
+ gsw@10110000 {
+ ralink,port4 = "ephy";
+ };
+
+ sdhci@10130000 {
+ status = "okay";
+ };
+
+ ehci@101c0000 {
+ status = "okay";
+ };
+
+ ohci@101c1000 {
+ status = "okay";
+ };
+
+ wmac@10180000 {
+ ralink,mtd-eeprom = <&factory 0>;
+ };
+
+ pcie@10140000 {
+ status = "okay";
+ };
+
+ sound {
+ compatible = "mediatek,mt7620-audio-wm8960";
+ model = "mt7620-wm8960";
+ i2s-controller = <&i2s>;
+ audio-routing =
+ "Ext Spk", "SPK_LP",
+ "Ext Spk", "SPK_LN",
+ "Ext Spk", "SPK_RP",
+ "Ext Spk", "SPK_RN";
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ power {
+ label = "cs-qr10:red:power";
+ gpios = <&gpio1 4 1>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ s1 {
+ label = "reset";
+ gpios = <&gpio1 1 1>;
+ linux,code = <0x198>;
+ };
+
+ s2 {
+ label = "wps";
+ gpios = <&gpio1 3 1>;
+ linux,code = <0x211>;
+ };
+ };
+};
diff --git a/target/linux/ramips/image/mt7620.mk
b/target/linux/ramips/image/mt7620.mk
index 18cd20a..2055116 100644
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -82,6 +82,7 @@ whr_1166d_mtd_size=15400960
Image/Build/Profile/WHR1166D=$(call
BuildFirmware/CustomFlash/$(1),$(1),whr-1166d,WHR-1166D,$(whr_1166d_mtd_size))
dlink810l_mtd_size=6881280
Image/Build/Profile/CF-WR800N=$(call
BuildFirmware/Default8M/$(1),$(1),cf-wr800n,CF-WR800N)
+Image/Build/Profile/CS-QR10=$(call
BuildFirmware/Default8M/$(1),$(1),cs-qr10,CS-QR10)
Image/Build/Profile/DIR-810L=$(call
BuildFirmware/CustomFlash/$(1),$(1),dir-810l,DIR-810L,$(dlink810l_mtd_size))
na930_mtd_size=20971520
Image/Build/Profile/NA930=$(call
BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
@@ -124,6 +125,7 @@ define Image/Build/Profile/Default
$(call Image/Build/Profile/MT7620a_V22SG,$(1))
$(call Image/Build/Profile/AI-BR100,$(1))
$(call Image/Build/Profile/CF-WR800N,$(1))
+ $(call Image/Build/Profile/CS-QR10,$(1))
$(call Image/Build/Profile/RP-N53,$(1))
$(call Image/Build/Profile/DIR-810L,$(1))
$(call Image/Build/Profile/WHR300HP2,$(1))
diff --git a/target/linux/ramips/mt7620/profiles/planex.mk
b/target/linux/ramips/mt7620/profiles/planex.mk
new file mode 100644
index 0000000..9d99cac
--- /dev/null
+++ b/target/linux/ramips/mt7620/profiles/planex.mk
@@ -0,0 +1,19 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/CS-QR10
+ NAME:=Planex CS-QR10
+ PACKAGES:=\
+ kmod-usb-core kmod-usb2 kmod-usb-ohci \
+ kmod-i2c-core kmod-i2c-ralink kmod-sound-core kmod-sound-mtk \
+ kmod-sdhci-mt7620
+endef
+
+define Profile/CS-QR10/Description
+ Package set optimized for the Planex CS-QR10.
+endef
+$(eval $(call Profile,CS-QR10))
--
1.9.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
