> > My Archer C7 v4 still bricks with the same error reported earlier and > > confirmed by Koen: Atheros AR8216/AR8236/AR8316: probe of > > ag71xx-mdio.0:00 failed with error -22 > > > > Hi All, > > I created a new branch in my staging tree, which is a replica of the > latest master tree, > but adds a fix for the switch issue + enables 4.14 on ar71xx by default. > > Feel free to build it and try it out. > Please provide some feedback if it worked for you. > > https://git.openwrt.org/?p=openwrt/staging/xback.git;a=shortlog;h=refs/heads/ar71xx_414
Thank you Koen, it fixes the switch issue for my Archer C7 v4 too: [ 0.713675] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0 [ 1.432868] libphy: ag71xx_mdio: probed [ 2.066476] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316] [ 2.077962] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:SGMII Now that the switch works I've noticed that the 5GHz wifi on my Archer C7 v4 doesn't work with Kernel 4.14 enabled: [ 10.005449] pci 0000:00:00.0: no irq found for pin 1 [ 10.011893] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 10.017960] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 [ 10.298735] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2 [ 10.309822] ath10k_pci 0000:00:00.0: Falling back to user helper [ 10.475669] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed [ 10.485244] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2 [ 10.495966] ath10k_pci 0000:00:00.0: Falling back to user helper [ 10.704794] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2 [ 10.715891] ath10k_pci 0000:00:00.0: Falling back to user helper [ 10.811651] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed [ 10.827803] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000 [ 10.837374] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 [ 10.850379] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00037 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb [ 10.948081] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2 [ 10.958903] ath10k_pci 0000:00:00.0: Falling back to user helper [ 11.033046] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed [ 11.042531] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 [ 13.164858] ath10k_pci 0000:00:00.0: failed to receive control response completion, polling.. [ 14.204850] ath10k_pci 0000:00:00.0: Service connect timeout [ 14.210703] ath10k_pci 0000:00:00.0: failed to connect htt (-145) [ 14.346078] ath10k_pci 0000:00:00.0: could not init core (-145) [ 14.352322] ath10k_pci 0000:00:00.0: could not probe fw (-145) [ 14.408888] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=47 Full log: https://pastebin.com/x6u8LEXN Best regards Sven Am Do., 30. Aug. 2018 um 19:18 Uhr schrieb Koen Vandeputte <[email protected]>: > > > > On 2018-08-23 19:00, Sven Schönhoff wrote: > >>>> curious what i missed as my archer-c7-v4 is working fine..... TPLINK > >>>> AC1750 device > >>> Hi, > >>> please dont top post > >>> I have no idea what you are asking. > >>> > >> Meaning I don't understand his issue mine works fine, so I'm curious as to > >> what's different > > I would guess you didn't change KERNEL_PATCHVER to 4.14 in > > target/linux/ar71xx/Makefile. Kernel 4.14 is not enabled by default > > yet for ar71xx. > > > > My Archer C7 v4 still bricks with the same error reported earlier and > > confirmed by Koen: Atheros AR8216/AR8236/AR8316: probe of > > ag71xx-mdio.0:00 failed with error -22 > > > > Hi All, > > I created a new branch in my staging tree, which is a replica of the > latest master tree, > but adds a fix for the switch issue + enables 4.14 on ar71xx by default. > > Feel free to build it and try it out. > Please provide some feedback if it worked for you. > > https://git.openwrt.org/?p=openwrt/staging/xback.git;a=shortlog;h=refs/heads/ar71xx_414 > > > > [ 0.000000] Linux version 4.14.67 (kvdp@kvdp-BRIX) (gcc version 7.3.0 > (OpenWrt GCC 7.3.0 r7984+5-555c59230402)) #0 Thu Aug 30 14:32:54 2018 > ... > [ 0.138438] MIPS: machine is Mikrotik RouterBOARD 2011UiAS > ... > [ 11.163357] libphy: Fixed MDIO Bus: probed > [ 11.319898] libphy: ag71xx_mdio: probed > [ 11.360844] switch0: Atheros AR8327 rev. 4 switch registered on > ag71xx-mdio.0 > [ 12.447398] libphy: ag71xx_mdio: probed > [ 13.077402] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 > [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316] > [ 13.088989] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII > [ 13.717716] ag71xx-mdio.1: Found an AR934X built-in switch > [ 13.769990] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII > > > > > Thanks, > > Koen _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
