Specification:
- SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU
- RAM: 512MB DDR3 System Memory
- NOR Flash: 32MB SPI NOR
- NAND Flash: 256MB NAND
- Ethernet: 5 x 1G via QCA8337N
- USB: 2 x USB 3.0 SuperSpeed
- PCIe: 3x Mini PCIe 2.0 Slots
Three PCIE2.0 connectors can connect two or three radio cards
such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN
How to flash via u-boot console:
tftpboot 0x44000000
openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin
nand erase 0x1340000 0x4000000
nand write 0x44000000 0x1340000 $filesize
setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’
saveenv
bootm
Further upgrades via sysupgrade.
Tested on IPQ8064 AP161 Board:
1) NAND boot
2) Tested USB and PCIe interfaces
3) WDOG test
4) cpu frequency scaling
5) ethernet, 2G and 5G WiFi
6) ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <[email protected]>
---
.../ipq806x/base-files/etc/board.d/02_network | 5 +
.../ipq806x/base-files/lib/upgrade/platform.sh | 1 +
.../arch/arm/boot/dts/qcom-ipq8064-ap161.dts | 277 +++++++++++++++++++++
target/linux/ipq806x/image/Makefile | 13 +
.../patches-4.14/0069-arm-boot-add-dts-files.patch | 3 +-
5 files changed, 298 insertions(+), 1 deletion(-)
create mode 100644
target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-ap161.dts
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network
b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 786c6f7..3417466 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -21,6 +21,11 @@ tplink,vr2600v)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
;;
+qcom,ipq8064-ap161)
+ ucidef_set_interface_lan "eth1 eth2"
+ ucidef_add_switch "switch0" \
+ "0:lan" "1:lan" "2:lan" "3u@eth1" "6:wan" "4u@eth0"
+ ;;
linksys,ea8500)
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index 6e282f9..4b88f9c 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -16,6 +16,7 @@ platform_do_upgrade() {
netgear,r7500v2 |\
netgear,r7800 |\
qcom,ipq8064-ap148 |\
+ qcom,ipq8064-ap161 |\
zyxel,nbg6817)
nand_do_upgrade "$ARGV"
;;
diff --git
a/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-ap161.dts
b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-ap161.dts
new file mode 100644
index 0000000..60c83a7
--- /dev/null
+++ b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-ap161.dts
@@ -0,0 +1,277 @@
+#include "qcom-ipq8064-v1.0.dtsi"
+
+/ {
+ model = "Qualcomm IPQ8064/AP161";
+ compatible = "qcom,ipq8064-ap161", "qcom,ipq8064";
+
+ memory@0 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &gsbi4_serial;
+ mdio-gpio0 = &mdio0;
+ };
+
+ chosen {
+ linux,stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ pinmux@800000 {
+ i2c4_pins: i2c4_pinmux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ bias-disable;
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+ };
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
+ };
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio2", "gpio27", "gpio28",
+ "gpio29", "gpio30", "gpio31",
+ "gpio32", "gpio51", "gpio52",
+ "gpio59", "gpio60", "gpio61",
+ "gpio62" , "gpio66";
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+ };
+
+ gsbi5: gsbi@1a200000 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "ok";
+
+ spi4: spi@1a280000 {
+ status = "ok";
+ spi-max-frequency = <50000000>;
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 0>;
+
+ flash: m25p80@0 {
+ compatible = "s25fl256s1";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "qcom,smem";
+ };
+ };
+ };
+ };
+
+ sata-phy@1b400000 {
+ status = "ok";
+ };
+
+ sata@29000000 {
+ status = "ok";
+ };
+
+ phy@100f8800 { /* USB3 port 1 HS phy */
+ status = "ok";
+ };
+
+ phy@100f8830 { /* USB3 port 1 SS phy */
+ status = "ok";
+ };
+
+ phy@110f8800 { /* USB3 port 0 HS phy */
+ status = "ok";
+ };
+
+ phy@110f8830 { /* USB3 port 0 SS phy */
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
+
+ pcie0: pci@1b500000 {
+ status = "ok";
+ };
+
+ pcie1: pci@1b700000 {
+ status = "ok";
+ force_gen1 = <1>;
+ };
+
+ pcie2: pci@1b900000 {
+ status = "ok";
+ };
+
+ nand@1ac00000 {
+ status = "ok";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ cs0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "qcom,smem";
+ };
+ };
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x20080 /* PAD6_MODE */
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ phy_rgmii_en = <1>;
+ txclk_delay_en = <1>;
+ rxclk_delay_en = <1>;
+ };
+
+ phy3: ethernet-phy@3 {
+ device_type = "ethernet-phy";
+ reg = <3>;
+ };
+ };
+
+ gmac0: ethernet@37000000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <0>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
+
+&adm_dma {
+ status = "ok";
+};
diff --git a/target/linux/ipq806x/image/Makefile
b/target/linux/ipq806x/image/Makefile
index b82d54b..5902eee 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -201,6 +201,19 @@ define Device/qcom_ipq8064-ap148-legacy
endef
TARGET_DEVICES += qcom_ipq8064-ap148-legacy
+define Device/qcom_ipq8064-ap161
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_DTS := qcom-ipq8064-ap161
+ KERNEL_INSTALL := 1
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ BOARD_NAME := ap161
+ DEVICE_TITLE := Qualcomm AP161
+ DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
+endef
+TARGET_DEVICES += qcom_ipq8064-ap161
+
define Device/qcom_ipq8064-db149
$(call Device/FitImage)
DEVICE_DTS := qcom-ipq8064-db149
diff --git
a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch
b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch
index b94e482..0a62a0b 100644
--- a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch
@@ -10,13 +10,14 @@ Signed-off-by: John Crispin <[email protected]>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -699,6 +699,16 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -699,6 +699,17 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8084-mtp.dtb \
qcom-ipq4019-ap.dk01.1-c1.dtb \
qcom-ipq8064-ap148.dtb \
+ qcom-ipq8064-c2600.dtb \
+ qcom-ipq8064-d7800.dtb \
+ qcom-ipq8064-db149.dtb \
++ qcom-ipq8064-ap161.dtb \
+ qcom-ipq8064-ea8500.dtb \
+ qcom-ipq8064-r7500.dtb \
+ qcom-ipq8064-r7500v2.dtb \
--
1.9.1
_______________________________________________
openwrt-devel mailing list
[email protected]
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
