On Friday, December 7, 2018 8:49:33 PM CET Hauke Mehrtens wrote: > This updates the backports package used in mac80211 to version 4.19.7-1 > which is based on kernel 4.19.7. This integrates all the stable fixes > introduces in this kernel version. > > The deleted patches are not needed any more because they are either > included in the upstream Linux kernel 4.19.7 or in backports 4.19.7-1. > > Signed-off-by: Hauke Mehrtens <[email protected]> > --- > package/kernel/mac80211/Makefile | 6 +- > .../patches/ath/080-ath10k_thermal_config.patch | 2 +- > .../patches/ath/402-ath_regd_optional.patch | 2 +- > .../patches/ath/404-regd_no_assoc_hints.patch | 4 +- > .../patches/ath/551-ath9k_ubnt_uap_plus_hsr.patch | 2 +- > ...dling-of-peer_bw_rxnss_override-parameter.patch | 2 +- > ...-controlling-support-for-various-chipsets.patch | 14 +-- > .../brcm/100-brcmfmac-fix-roamoff-1-modparam.patch | 15 +-- > ...ix-for-proper-support-of-160MHz-bandwidth.patch | 117 > --------------------- > ...move-recursion-from-firmware-load-error-h.patch | 17 +-- > .../patches/build/005-revert-devcoredump.patch | 8 -- > .../patches/build/060-no_local_ssb_bcma.patch | 4 +- > .../rt2x00/602-rt2x00-introduce-rt2x00eeprom.patch | 2 +- > .../patches/subsys/140-tweak-TSQ-setting.patch | 2 +- > ...x-setting-IEEE80211_KEY_FLAG_RX_MGMT-for-.patch | 25 ----- > ...-free-skb-fraglist-before-freeing-the-skb.patch | 2 +- > ...-mac80211-add-hdrlen-to-ieee80211_tx_data.patch | 10 +- > ...8-mac80211-add-NEED_ALIGNED4_SKBS-hw-flag.patch | 18 ++-- > ...x-memory-accounting-with-A-MSDU-aggregati.patch | 6 +- > ...nore-tx-status-for-PS-stations-in-ieee802.patch | 2 +- > ...x-reordering-of-buffered-broadcast-packet.patch | 2 +- > ...locate-TXQs-for-active-monitor-interfaces.patch | 26 ----- > 22 files changed, 52 insertions(+), 236 deletions(-) > delete mode 100644 > package/kernel/mac80211/patches/brcm/304-v4.20-0001-brcmfmac-fix-for-proper-support-of-160MHz-bandwidth.patch > delete mode 100644 > package/kernel/mac80211/patches/build/005-revert-devcoredump.patch > delete mode 100644 > package/kernel/mac80211/patches/subsys/350-mac80211-fix-setting-IEEE80211_KEY_FLAG_RX_MGMT-for-.patch > delete mode 100644 > package/kernel/mac80211/patches/subsys/394-mac80211-allocate-TXQs-for-active-monitor-interfaces.patch
I think that the package/kernel/mac80211/patches/ath/936-ath10k-fix-otp-failure-result.patch hack can be removed at this point. The upstream patch that fixed the mess was added long ago. |commit a9f5f287fa1d47d61dfa8b60f94831174b2ea4d0 |Author: Anilkumar Kolli <[email protected]> |Date: Wed May 31 14:21:27 2017 +0300 | | ath10k: add BMI parameters to fix calibration from DT/pre-cal | | QCA99X0, QCA9888, QCA9984 supports calibration data in | either OTP or DT/pre-cal file. Current ath10k supports | Calibration data from OTP only. | | If caldata is loaded from DT/pre-cal file, fetching board id | and applying calibration parameters like tx power gets failed. | | error log: | [ 15.733663] ath10k_pci 0000:01:00.0: failed to fetch board file: -2 | [ 15.741474] ath10k_pci 0000:01:00.0: could not probe fw (-2) | | This patch adds calibration data support from DT/pre-cal | file. Below parameters are used to get board id and | applying calibration parameters from cal data. | | EEPROM[OTP] FLASH[DT/pre-cal file] | Cal param 0x700 0x10000 | Board id 0x10 0x8000 | | Tested on QCA9888 with pre-cal file. | | Signed-off-by: Anilkumar Kolli <[email protected]> | Signed-off-by: Kalle Valo <[email protected]> And the affected ar71xx/ath79, ipq806x devices which have a QCA99X0, QCA9888 or QCA9984 devices were converted from the hackish cal- to the supported pre-cal method a long time ago too. Regards, Christian _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
