Hello Christian, On 10.03.19 20:27, Christian Lamparter wrote: > On Saturday, March 9, 2019 12:20:54 AM CET David Bauer wrote: >> Hardware >> -------- >> CPU: Qualcomm IPQ4019 >> RAM: 256M (NANYA NT5CC128M16JR-EK) >> FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI) >> ETH: Qualcomm QCA8072 >> WiFi2: IPQ4019 2T2R 2SS b/g/n >> WiFi5: IPQ4019 2T2R 2SS n/ac >> WiFi5: QCA9984 4T4R 4SS n/ac >> LED: - Connect green/blue/red >> - Power green >> BTN: WPS/Connect >> UART: 115200n8 3.3V >> VCC - RX - TX - GND (Square is VCC) >> >> Installation >> ------------ >> 1. Grab the uboot for the Device from the 'u-boot-fritz3000' >> subdirectory. Place it in the same directory as the 'eva_ramboot.py' >> script. It is located in the 'scripts/flashing' subdirectory of the >> OpenWRT tree. >> >> 2. Assign yourself the IP address 192.168.178.10/24. Connect your >> Computer to one of the boxes LAN ports. >> >> 3. Connect Power to the Box. As soon as the LAN port of your computer >> shows link, load the U-Boot to the box using following command. >> >> > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin >> >> 4. The U-Boot will now start. Now assign yourself the IP address >> 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP >> server root directory and rename it to 'FRITZ3000.bin'. >> >> 5. The Box will now boot OpenWRT from RAM. This can take up to two >> minutes. >> >> 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using >> scp. SSH into the Box and first write the Bootloader to both previous >> kernel partitions. >> >> > mtd write /path/to/uboot-fritz3000.bin uboot0 >> > mtd write /path/to/uboot-fritz3000.bin uboot1 >> >> 7. Remove the AVM filesystem partitions to make room for our kernel + >> rootfs + overlayfs. >> >> > ubirmvol /dev/ubi0 --name=avm_filesys_0 >> > ubirmvol /dev/ubi0 --name=avm_filesys_1 >> >> 8. Flash OpenWRT peristently using sysupgrade. >> >> > sysupgrade -n /path/to/openwrt-sysupgrade.bin >> >> Signed-off-by: David Bauer <[email protected]> >> --- >> diff --git a/target/linux/ipq40xx/image/Makefile >> b/target/linux/ipq40xx/image/Makefile >> index 3a7ecf39eb..49ff71c6bc 100644 >> --- a/target/linux/ipq40xx/image/Makefile >> +++ b/target/linux/ipq40xx/image/Makefile >> @@ -130,6 +130,15 @@ define Device/avm_fritzbox-7530 >> endef >> TARGET_DEVICES += avm_fritzbox-7530 >> >> +define Device/avm_fritzrepeater-3000 >> + $(call Device/FitImageLzma) >> + DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000 >> + DEVICE_TITLE := AVM Fritz!Repeater 3000 >> + DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata >> ipq-wifi-avm_fritzrepeater-3000 > The fritz-tffs-nand was just added to openwrt. > > <https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=50717510e7e556cbc9ef05887900a7dc93a57793> > > Should I add it in place? (And for the 7530 as well?)
I will submit a follow-up patch regarding tis topic as it was merged without this issue addressed. I have already prepared a patch for this, but will test it tomorrow on all 3 affected devices (7530, 3000 and 7412). Best wishes David > > Cheers, > Christian > > > _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
