On 26.05.19 22:46, Cezary Jackiewicz wrote: > Dnia 2019-05-26, o godz. 22:16:30 > Birger Koblitz <m...@birger-koblitz.de> napisał(a): > >> Hi, >> >> On 26.05.19 19:28, Cezary Jackiewicz wrote: >>>> + ucidef_set_led_netdev "lan" "lan" "$boardname:green:internet" >>>> "eth0" >>>> + ;; >>> Also working: >>> >>> ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x20" >>> >>> (if you rename internet to lan) >>> >> Are you sure about this? I renamed the internet to lan, but on the >> 7476rpc the led does not turn on: > On 7478ac, yes, i'm sure. > > root@OpenWrt:~# swconfig dev switch0 show | grep port > link: port:0 link:down > link: port:1 link:down > link: port:2 link:down > link: port:3 link:down > link: port:4 link:down > link: port:5 link:up speed:1000baseT full-duplex > link: port:6 link:up speed:1000baseT full-duplex > link: port:7 link:down > root@OpenWrt:~# cat /sys/class/leds/ew-7478ac\:green\:lan/trigger > none [switch0] timer default-on netdev phy0rx phy0tx phy0assoc phy0radio > phy0tpt phy1rx phy1tx phy1assoc phy1radio > root@OpenWrt:~# cat /sys/class/leds/ew-7478ac\:green\:lan/port_mask > 0x20 > root@OpenWrt:~#
I get: root@OpenWrt:~# ls /sys/class/leds/ew-7476rpc\:green\:lan/ brightness device device_name interval link max_brightness rx subsystem trigger tx uevent no port_mask > >> SoC: MediaTek MT7620a @ 580MHz >> RAM: 64M (Winbond W9751G6KB-25) >> FLASH: 16MB (Macronix) > Are you sure? On your dts: > >> + partition@70000 { >> + compatible = "edimax,uimage"; >> + label = "firmware"; >> + reg = <0x00070000 0x00790000>; >> + }; > This is 8MB Yes, you are right, according to http://www.acelink.com.tw/EW-7476RPC.html > > [ 1.274276] spi spi0.0: force spi mode3 > [ 1.282777] m25p80 spi0.0: mx25l6405d (8192 Kbytes) > [ 1.292601] 5 fixed-partitions partitions found on MTD device spi0.0 > [ 1.305262] Creating 5 MTD partitions on "spi0.0": > > > >> Installation >> ------------ >> Update the factory image via the web-interfaces (by default: >> 192.168.9.2/24). >> http://192.168.9.2/index.asp > Or push wpa button on power on and send firmware via tftp to 192.168.1.6 > >> ramips: add Netgear EW-7478AC >> >> SoC: MediaTek MT7620a @ 580MHz >> RAM: 64M (Winbond W9751G6KB-25) >> FLASH: 16MB (Macronix) > 8MB :) in version sold in Poland. > > Unfortunately also in Germany :( . Otherwise I looked into the firmware of the Edimax RE-11 and there the magic bytes are RN74. Otherwise the firmware looks identical to the other models. Birger _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel