Hi, > -----Original Message----- > From: openwrt-devel [mailto:[email protected]] On > Behalf Of André Valentin > Sent: Dienstag, 22. Oktober 2019 11:52 > To: [email protected] > Cc: [email protected] > Subject: [OpenWrt-Devel] [PATCH 3/3] ath79: add support for ZyXEL NBG6716 > > Attention: Kernel partition size has been enlarged to 4MB. > To switch, you must update to latest ar71xx-nand snapshort and flash the > sysupgrade-4M-Kernel.bin: > > zcat openwrt-ath79-nand-zyxel_nbg6716-squashfs-sysupgrade-4M-Kernel.bin | mtd > -r -e ubi write - firmware; reboot -f > You will end up with a fresh config if you do not inject config into the > image. > > Access the real u-boot shell: > ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02" > When the device is starting up, the user can enter the the loader shell > by simply pressing a key within the 3 seconds once the following string > appears on the serial console: > > | Hit any key to stop autoboot: 3 > > The user is then dropped to a locked shell. > > |NBG6716> HELP > |ATEN x[,y] set BootExtension Debug Flag (y=password) > |ATSE x show the seed of password generator > |ATSH dump manufacturer related data in ROM > |ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, > u=iterations) > |ATGO boot up whole system > |ATUR x upgrade RAS image (filename) > |NBG6716> > > In order to escape/unlock a password challenge has to be passed. > Note: the value is dynamic! you have to calculate your own! > > First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env) > to get the challange value/seed. > > |NBG6716> ATSE NBG6716 > |012345678901 > > This seed/value can be converted to the password with the help of this > bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors): > > - tool.sh - > ror32() { > echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) > } > v="0x$1" > a="0x${v:2:6}" > b=$(( $a + 0x10F0A563)) > c=$(( 0x${v:12:14} & 7 )) > p=$(( $(ror32 $b $c) ^ $a )) > printf "ATEN 1,%X\n" $p > - end of tool.sh - > > |# bash ./tool.sh 012345678901 > | > |ATEN 1,879C711 > > copy and paste the result into the shell to unlock zloader. > > |NBG6716> ATEN 1,0046B0017430 > > If the entered code was correct the shell will change to > use the ATGU command to enter the real u-boot shell. > > |NBG6716> ATGU > |NBG6716# > > idsfg > > Signed-off-by: André Valentin <[email protected]> > --- > .../ath79/base-files/etc/board.d/02_network | 8 + > .../etc/hotplug.d/firmware/10-ath9k-eeprom | 4 + > .../etc/hotplug.d/firmware/11-ath10k-caldata | 4 + > .../etc/hotplug.d/ieee80211/00-wifi-migration | 3 +- > .../ath79/base-files/lib/upgrade/platform.sh | 3 + > target/linux/ath79/dts/qca9557.dtsi | 18 ++ > .../linux/ath79/dts/qca9558_zyxel_nbg6716.dts | 296 ++++++++++++++++++ > target/linux/ath79/image/Makefile | 1 + > target/linux/ath79/image/common-zyxel.mk | 29 ++ > target/linux/ath79/image/nand-zyxel.mk | 21 ++ > 10 files changed, 386 insertions(+), 1 deletion(-) > create mode 100644 target/linux/ath79/dts/qca9558_zyxel_nbg6716.dts > create mode 100644 target/linux/ath79/image/common-zyxel.mk > create mode 100644 target/linux/ath79/image/nand-zyxel.mk > > diff --git a/target/linux/ath79/base-files/etc/board.d/02_network > b/target/linux/ath79/base-files/etc/board.d/02_network > index fe74bddbf1..42f3462b89 100755 > --- a/target/linux/ath79/base-files/etc/board.d/02_network > +++ b/target/linux/ath79/base-files/etc/board.d/02_network > @@ -301,6 +301,10 @@ ath79_setup_interfaces() > ucidef_add_switch "switch0" \ > "0@eth0" "3:lan:1" "4:lan:2" > ;; > + zyxel,nbg6716) > + ucidef_add_switch "switch0" \ > + "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" > "6@eth1" > + ;; > *) > ucidef_set_interfaces_lan_wan "eth0" "eth1" > ;; > @@ -435,6 +439,10 @@ ath79_setup_macs() > wd,mynet-wifi-rangeextender) > lan_mac=$(nvram get et0macaddr) > ;; > + zyxel,nbg6716) > + lan_mac=$(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) > +2) > + wan_mac=$(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) > +3) > + ;; > esac > > [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac > diff --git > a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom > b/target/linux/ath79/base- > files/etc/hotplug.d/firmware/10-ath9k-eeprom > index 3240026aec..cfffe5702a 100644 > --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom > +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom > @@ -46,6 +46,10 @@ case "$FIRMWARE" in > caldata_extract "radiocfg" 0x1000 0x440 > ath9k_patch_mac $(mtd_get_mac_ascii devdata "wlan24mac") > ;; > + zyxel,nbg6716) > + caldata_extract "art" 0x1000 0x440 > + ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 0x2
You need to remove the "0x2".
> + ;;
> *)
> caldata_die "board $board is not supported yet"
> ;;
> diff --git
> a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> b/target/linux/ath79/base-
> files/etc/hotplug.d/firmware/11-ath10k-caldata
> index 8ab0f6f6ad..cc0cd2b7c0 100644
> --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> @@ -112,6 +112,10 @@ case "$FIRMWARE" in
> ubnt,unifiac-pro)
> caldata_extract "EEPROM" 0x5000 0x844
> ;;
> + zyxel,nbg6716)
> + caldata_extract "art" 0x5000 0x844
> + ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii
> u-boot-env ethaddr) +1)
> + ;;
> esac
> ;;
> "ath10k/pre-cal-pci-0000:00:00.0.bin")
> diff --git
> a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/00-wifi-migration
> b/target/linux/ath79/base-
> files/etc/hotplug.d/ieee80211/00-wifi-migration
> index 37a1346fe7..b0a5d79f9d 100644
> --- a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/00-wifi-migration
> +++ b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/00-wifi-migration
> @@ -15,7 +15,8 @@ migrate_wifi_path() {
>
> case "$board" in
> tplink,archer-c7-v1|\
> - tplink,archer-c7-v2)
> + tplink,archer-c7-v2|\
> + zyxel,nbg6716)
> path="pci0000:00/0000:00:00.0"
> WIFI_PATH_CHANGED=1
> ;;
> diff --git a/target/linux/ath79/base-files/lib/upgrade/platform.sh
> b/target/linux/ath79/base-files/lib/upgrade/platform.sh
> index f4fca06384..46bd6ab9ef 100644
> --- a/target/linux/ath79/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ath79/base-files/lib/upgrade/platform.sh
> @@ -51,6 +51,9 @@ platform_do_upgrade() {
> ubnt,routerstation-pro)
> redboot_fis_do_upgrade "$1" kernel
> ;;
> + zyxel,nbg6716)
> + nand_do_upgrade "$1"
> + ;;
> *)
> default_do_upgrade "$1"
> ;;
> diff --git a/target/linux/ath79/dts/qca9557.dtsi
> b/target/linux/ath79/dts/qca9557.dtsi
> index b29dfc72b2..61e1d5f6a4 100644
> --- a/target/linux/ath79/dts/qca9557.dtsi
> +++ b/target/linux/ath79/dts/qca9557.dtsi
> @@ -178,6 +178,24 @@
> };
> };
>
> + nand: nand@1b800200 {
> + compatible = "qca,ar934x-nand";
> + reg = <0x1b800200 0xb8>;
> +
> + interrupts = <21>;
> + interrupt-parent = <&miscintc>;
> +
> + resets = <&rst 14>;
> + reset-names = "nand";
> +
> + nand-ecc-mode = "hw";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> gmac: gmac@18070000 {
> compatible = "qca,qca9550-gmac";
> reg = <0x18070000 0x58>;
> diff --git a/target/linux/ath79/dts/qca9558_zyxel_nbg6716.dts
> b/target/linux/ath79/dts/qca9558_zyxel_nbg6716.dts
> new file mode 100644
> index 0000000000..e0065cc012
> --- /dev/null
> +++ b/target/linux/ath79/dts/qca9558_zyxel_nbg6716.dts
> @@ -0,0 +1,296 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +#include "qca9557.dtsi"
> +
> +/ {
> + compatible = "zyxel,nbg6716", "qca,qca9558";
> + model = "ZyXEL NBG6716";
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + aliases {
> + led-boot = &power;
> + led-failsafe = &power;
> + led-running = &power;
> + led-upgrade = &power;
> + label-mac-device = ð0;
This won't work after you have removed the mtd-mac-address entries from DTS.
You will need to use label_mac in 02_network.
Despite, I'm still waiting for your explanation on the MAC address assignment.
> + };
Empty line missing.
> + leds {
> + compatible = "gpio-leds";
> +
> + power: power {
> + label = "nbg6716:white:power";
> + gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
> + };
> +
> + wan {
> + label = "nbg6716:white:internet";
> + gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
> + };
> + usb1 {
> + label = "nbg6716:white:usb1";
> + gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "usbport";
> + trigger-sources = <&hub_port0>;
> + };
> + usb2 {
> + label = "nbg6716:white:usb2";
> + gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "usbport";
> + trigger-sources = <&hub_port1>;
> + };
> + wifi2 {
> + label = "nbg6716:white:wifi2";
> + gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy1tpt";
> + };
> + wifi5 {
> + label = "nbg6716:white:wifi5";
> + gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy0tpt";
> + };
> + wps {
> + label = "nbg6716:white:wps";
> + gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
> + };
All nodes should be separated by one empty line, but without an empty line at
the beginning and the end inside the parent node.
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + reset {
> + label = "reset";
> + linux,code = <KEY_RESTART>;
> + gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
> +
> + wifi_button {
> + label = "WiFi button";
> + linux,code = <KEY_RFKILL>;
> + gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
> +
> + usb1 {
> + label = "USB1 eject button";
> + gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
> +
> + usb2 {
> + label = "USB2 eject button";
> + gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
Here, the indent is wrong.
> +
> + wps {
> + label = "WPS button";
> + linux,code = <KEY_WPS_BUTTON>;
> + gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
> + };
> + gpio-export {
> + compatible = "gpio-export";
> + #size-cells = <0>;
> +
> + gpio_usb_power {
> + gpio-export,name = "nbg6716:power:usb";
> + gpio-export,output = <1>;
> + gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
> + };
> + };
gpio-export is deprecated. Have a look at gpio-hog (should be easy to grep
inside the ath79 target).
> +};
> +
> +&uart {
> + status = "okay";
> +};
> +
> +&spi {
> + status = "okay";
> + num-cs = <1>;
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <25000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + uboot: partition@0 {
> + label = "u-boot";
> + reg = <0x000000 0x040000>;
> + read-only;
> + };
> +
> + uboot_env: partition@40000 {
> + label = "u-boot-env";
> + reg = <0x040000 0x010000>;
> + };
Indent!
> +
> + art: partition@50000 {
> + label = "art";
> + reg = <0x050000 0x010000>;
> + read-only;
> + };
> +
> + partition@60000 {
> + label = "nbu";
> + reg = <0x060000 0xFA0000>;
Consider switching to lower case.
> + };
> + };
> + };
> +};
> +
> +&nand {
> + status = "okay";
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "zyxel_rfsd";
> + reg = <0x0 0x200000>;
> + };
> +
> + partition@200000 {
> + label = "romd";
> + reg = <0x200000 0x200000>;
> + };
> +
> + partition@400000 {
> + label = "header";
> + reg = <0x400000 0x100000>;
> + };
> +
> + firmware@500000 {
> + label = "firmware";
> + reg = <0x500000 0x7B00000>;
Consider switching to lower case.
> + };
> +
> + partition@500000 {
> + label = "kernel";
> + reg = <0x500000 0x400000>;
> + };
> +
> + partition@900000 {
> + label = "ubi";
> + reg = <0x900000 0x7700000>;
> + };
> + };
> +};
> +
> +&mdio0 {
> + status = "okay";
> +
> + phy0: ethernet-phy@0 {
> + reg = <17>;
> + phy-mode = "rgmii-id";
> + };
> +
> + switch0@1f {
> + compatible = "qca,ar8327";
> + reg = <0x1f>;
> + qca,ar8327-initvals = <
> + 0x04 0x87600000 /* PORT0 PAD MODE CTRL */
> + 0x0c 0x00080080 /* PORT6 PAD MODE CTRL */
> + 0x10 0x81000080 /* POWER_ON_STRIP */
> + 0x50 0xffb7ffb7 /* LED_CTRL0 */
> + 0x54 0xffb7ffb7 /* LED_CTRL1 */
> + 0x58 0xffb7ffb7 /* LED_CTRL2 */
> + 0x5c 0x03ffff00 /* LED_CTRL3 */
> + 0x7c 0x0000007e /* PORT0_STATUS */
> + 0x94 0x0000007e /* PORT6 STATUS */
> + >;
> + };
> +};
> +
> +&mdio1 {
> + status = "okay";
> +
> + phy1: ethernet-phy@1 {
> + reg = <1>;
> + phy-mode = "sgmii";
> + };
> +};
> +
> +
> +ð0 {
> + status = "okay";
> +
> + pll-data = <0xa6000000 0x00000101 0x00001616>;
> + phy-handle = <&phy0>;
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +ð1 {
> + status = "okay";
> +
> + pll-data = <0x03000101 0x00000101 0x00001616>;
> + phy-handle = <&phy1>;
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&gpio {
> + status = "okay";
> +};
> +
> +&wmac {
> + status = "okay";
> +};
> +
> +&pcie1 {
> + status = "okay";
> +
> + wifi@0,0 {
> + compatible = "qcom,ath10k";
> + reg = <0 0 0 0 0>;
> + qcom,ath10k-calibration-variant = "ZyXEL-NBG6716";
> + };
> +};
> +
> +&usb_phy0 {
> + status = "okay";
> +};
> +
> +&usb_phy1 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +
> + hub_port0: port@1 {
> + reg = <1>;
> + #trigger-source-cells = <0>;
> + };
> +
> +};
> +
> +&usb1 {
> + status = "okay";
> +
> + hub_port1: port@1 {
> + reg = <1>;
> + #trigger-source-cells = <0>;
> + };
> +};
> +
Remove empty line at the end.
> diff --git a/target/linux/ath79/image/Makefile
> b/target/linux/ath79/image/Makefile
> index 24768ef5e0..074d7ead02 100644
> --- a/target/linux/ath79/image/Makefile
> +++ b/target/linux/ath79/image/Makefile
> @@ -77,6 +77,7 @@ include ./generic-ubnt.mk
> endif
> ifeq ($(SUBTARGET),nand)
> include ./nand.mk
> +include ./nand-zyxel.mk
At the moment, we have _one_ device inside nand.mk (and still only four after
jeffsf's changes).
I strongly suggest to just put the contents of both common-zyxel.mk and
nand-zyxel.mk into nand.mk, and not have one file per definition.
Best
Adrian
openpgp-digital-signature.asc
Description: PGP signature
_______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
