Hi, small nit at the end. W dniu 04.12.2019 o 19:14, Linus Lüssing pisze: > From: Linus Lüssing <l...@simonwunderlich.de> > > This adds support for the Ka-Ro MB7 board with a TX6U-8033 module. > > Specification, according to Linux DTS commit: > > TX6U-8033: > Processor Freescale i.MX 6 Dual Lite, 800MHz > RAM 1GiB DDR3 SDRAM > ROM 4GiB eMMC > Power supply Single 3.1V to 5.5V > Size 31mm SO-DIMM > Temp. Range industrial grade (-40°C/-25°C to 105°C Tj) > > The u-boot shipped by the vendor by default expects the following partition > layout: > > MBR/MSDOS, disk-id '0cc66cc0' { > 0cc66cc0-01 => ext2, /vmlinuz > 0cc66cc0-02 => ext4, rootfs > } > > TX6DL U-Boot > env print > append_bootargs=rootfstype=ext4 > [...] > bootcmd_mmc=setenv autostart no;run bootargs_mmc;ext2load mmc 0 ${kerneladdr} > vmlinuz > [...] > rootpart_uuid=0cc66cc0-02 > [...] > > This is also one of the reasons, why only ext4 rootfs support was added > and tested so far. No squashfs support yet. > > Other than that, nothing fancy needs to be added or preserved on the > eMMC. > > Cc: Simon Wunderlich <s...@simonwunderlich.de> > Signed-off-by: Linus Lüssing <l...@simonwunderlich.de> > --- > > Changelog v2: > * removed wildcard board names > > target/linux/imx6/Makefile | 2 +- > .../imx6/base-files/etc/board.d/02_network | 3 +- > target/linux/imx6/base-files/lib/imx6.sh | 4 + > .../base-files/lib/preinit/79_move_config | 9 ++ > .../imx6/base-files/lib/upgrade/platform.sh | 108 +++++++++++++++++- > target/linux/imx6/image/Makefile | 34 ++++++ > .../linux/imx6/image/gen_karo_sdcard_img.sh | 26 +++++ > .../imx6/patches-4.14/100-bootargs.patch | 13 +++ > tools/Makefile | 1 + > 9 files changed, 197 insertions(+), 3 deletions(-) > create mode 100755 target/linux/imx6/image/gen_karo_sdcard_img.sh > > diff --git a/target/linux/imx6/Makefile b/target/linux/imx6/Makefile > index ac4300f7eb..8083a54e16 100644 > --- a/target/linux/imx6/Makefile > +++ b/target/linux/imx6/Makefile > @@ -20,6 +20,6 @@ include $(INCLUDE_DIR)/target.mk > > KERNELNAME:=zImage dtbs > > -DEFAULT_PACKAGES += uboot-envtools mkf2fs e2fsprogs blkid > +DEFAULT_PACKAGES += uboot-envtools mkf2fs e2fsprogs blkid partx-utils > > $(eval $(call BuildTarget)) > diff --git a/target/linux/imx6/base-files/etc/board.d/02_network > b/target/linux/imx6/base-files/etc/board.d/02_network > index 6ec667346d..c662be72b7 100755 > --- a/target/linux/imx6/base-files/etc/board.d/02_network > +++ b/target/linux/imx6/base-files/etc/board.d/02_network > @@ -21,7 +21,8 @@ cubox-i |\ > *gw552x) > ucidef_set_interfaces_lan_wan 'eth0' 'eth1' > ;; > -*wandboard) > +*wandboard |\ > +tx6u-8033) > ucidef_set_interface_wan 'eth0' > ;; > esac > diff --git a/target/linux/imx6/base-files/lib/imx6.sh > b/target/linux/imx6/base-files/lib/imx6.sh > index 68caaff15f..c4b87d1c21 100755 > --- a/target/linux/imx6/base-files/lib/imx6.sh > +++ b/target/linux/imx6/base-files/lib/imx6.sh > @@ -99,6 +99,10 @@ imx6_board_detect() { > name="wandboard" > ;; > > + "Ka-Ro electronics TX6U-8033 Module on MB7 baseboard") > + name="tx6u-8033" > + ;; > + > *) > name="generic" > ;; > diff --git a/target/linux/imx6/base-files/lib/preinit/79_move_config > b/target/linux/imx6/base-files/lib/preinit/79_move_config > index bdf397c4fc..de7196c7a1 100644 > --- a/target/linux/imx6/base-files/lib/preinit/79_move_config > +++ b/target/linux/imx6/base-files/lib/preinit/79_move_config > @@ -15,6 +15,15 @@ move_config() { > umount /boot > fi > ;; > + tx6u-8033) > + local bootpart=/dev/mmcblk2p1 > + > + if [ -b $bootpart ]; then > + mkdir -p /boot > + mount -t ext2 -o rw,noatime $bootpart /boot > + [ -f /boot/sysupgrade.tgz ] && mv -f > /boot/sysupgrade.tgz / > + fi > + ;; > esac > } > > diff --git a/target/linux/imx6/base-files/lib/upgrade/platform.sh > b/target/linux/imx6/base-files/lib/upgrade/platform.sh > index a090cc080b..9c9bed96fe 100755 > --- a/target/linux/imx6/base-files/lib/upgrade/platform.sh > +++ b/target/linux/imx6/base-files/lib/upgrade/platform.sh > @@ -1,5 +1,5 @@ > # > -# Copyright (C) 2010-2015 OpenWrt.org > +# Copyright (C) 2010-2019 OpenWrt.org > # > > . /lib/imx6.sh > @@ -30,6 +30,102 @@ apalis_do_upgrade() { > umount /boot > } > > +# (mostly) copied from brcm2708 platform.sh (which was copied from x86?) > +tx6u_8033_check_image() { > + local diskdev partdev diff > + > + [ "$#" -gt 1 ] && return 1 > + > + export_bootdevice && export_partdevice diskdev 0 || { > + echo "Unable to determine upgrade device" > + return 1 > + } > + > + get_partitions "/dev/$diskdev" bootdisk > + > + #extract the boot sector from the image > + get_image "$@" | dd of=/tmp/image.bs count=1 bs=512b 2>/dev/null > + > + get_partitions /tmp/image.bs image > + > + #compare tables > + diff="$(grep -F -x -v -f /tmp/partmap.bootdisk /tmp/partmap.image)" > + > + rm -f /tmp/image.bs /tmp/partmap.bootdisk /tmp/partmap.image > + > + if [ -n "$diff" ]; then > + echo "Partition layout has changed. Full image will be written." > + ask_bool 0 "Abort" && exit 1 > + return 0 > + fi > + > + return 0; > +} > + > +# (mostly) copied from brcm2708 platform.sh (which was copied from x86?) > +tx6u_8033_do_upgrade() { > + local diskdev partdev diff > + > + export_bootdevice && export_partdevice diskdev 0 || { > + echo "Unable to determine upgrade device" > + return 1 > + } > + > + sync > + > + if [ "$SAVE_PARTITIONS" = "1" ]; then > + get_partitions "/dev/$diskdev" bootdisk > + > + #extract the boot sector from the image > + get_image "$@" | dd of=/tmp/image.bs count=1 bs=512b > + > + get_partitions /tmp/image.bs image > + > + #compare tables > + diff="$(grep -F -x -v -f /tmp/partmap.bootdisk > /tmp/partmap.image)" > + else > + diff=1 > + fi > + > + if [ -n "$diff" ]; then > + get_image "$@" | dd of="/dev/$diskdev" bs=2M conv=fsync > + > + # Separate removal and addtion is necessary; otherwise, > partition 1 > + # will be missing if it overlaps with the old partition 2 > + partx -d - "/dev/$diskdev" > + partx -a - "/dev/$diskdev" > + > + return 0 > + fi > + > + #iterate over each partition from the image and write it to the boot > disk > + while read part start size; do > + if export_partdevice partdev $part; then > + echo "Writing image to /dev/$partdev..." > + get_image "$@" | dd of="/dev/$partdev" ibs="512" obs=1M > skip="$start" count="$size" conv=fsync > + else > + echo "Unable to find partition $part device, skipped." > + fi > + done < /tmp/partmap.image > + > + #copy partition uuid > + echo "Writing new UUID to /dev/$diskdev..." > + get_image "$@" | dd of="/dev/$diskdev" bs=1 skip=440 count=4 seek=440 > conv=fsync > +} > + > +# (mostly) copied from brcm2708 platform.sh (which was copied from x86?) > +tx6u_8033_copy_config() { > + local partdev > + > + if export_partdevice partdev 1; then > + mkdir -p /boot > + [ -f /boot/vmlinuz.img ] || mount -t ext4 -o rw,noatime > "/dev/$partdev" /boot > + cp -af "$UPGRADE_BACKUP" "/boot/$BACKUP_FILE" > + sync > + unmount /boot > + fi > +} > + > platform_check_image() { > local board=$(board_name) > > @@ -41,6 +137,10 @@ platform_check_image() { > nand_do_platform_check $board $1 > return $?; > ;; > + tx6u-8033) > + tx6u_8033_check_image "$1" > + return $?; > + ;; > esac > > echo "Sysupgrade is not yet supported on $board." > @@ -57,6 +157,9 @@ platform_do_upgrade() { > *gw5*) > nand_do_upgrade "$1" > ;; > + tx6u-8033) > + tx6u_8033_do_upgrade "$1" > + ;; > esac > } > > @@ -67,6 +170,9 @@ platform_copy_config() { > apalis*) > apalis_copy_config > ;; > + tx6u-8033) > + tx6u_8033_copy_config > + ;; > esac > } > > diff --git a/target/linux/imx6/image/Makefile > b/target/linux/imx6/image/Makefile > index d1e9e9034e..34fb4a2690 100644 > --- a/target/linux/imx6/image/Makefile > +++ b/target/linux/imx6/image/Makefile > @@ -113,6 +113,24 @@ define Build/apalis-emmc > $(Build/imx6-combined-image-clean) > endef > > +define Build/karo-boot-img > + $(RM) -rf $@.bootdir > + mkdir $@.bootdir > + > + $(CP) $(IMAGE_KERNEL) $@.bootdir/$(KERNEL_IMG) > + > + genext2fs --block-size $(BLOCKSIZE:%k=%Ki) --size-in-blocks $$((1024 * > 1024 * $(CONFIG_TARGET_KERNEL_PARTSIZE) / ($(subst k,* 1024,$(BLOCKSIZE))))) > --root $@.bootdir $@.boot > + > + # convert it to revision 1 - needed for u-boot ext2load > + $(STAGING_DIR_HOST)/bin/tune2fs -O filetype $@.boot > + $(STAGING_DIR_HOST)/bin/e2fsck -pDf $@.boot > /dev/null > +endef > + > +define Build/karo-sdcard-img > + ./gen_karo_sdcard_img.sh $@ $@.boot $(IMAGE_ROOTFS) > $(CONFIG_TARGET_KERNEL_PARTSIZE) $(CONFIG_TARGET_ROOTFS_PARTSIZE) > +endef > + > + > ################################################# > # Devices > ################################################# > @@ -232,4 +250,20 @@ define Device/apalis > endef > TARGET_DEVICES += apalis > > +define Device/tx6u-8033 > + DEVICE_TITLE := Ka-Ro electronics TX6U-8033 Module on MB7 baseboard > + DEVICE_DTS := imx6dl-tx6u-8033 > + FILESYSTEMS := ext4 > + BLOCKSIZE := 4k > + KERNEL_SUFFIX := -zImage > + KERNEL_NAME := zImage > + KERNEL := kernel-bin > + KERNEL_IMG := vmlinuz > + IMAGES := factory.img.gz sysupgrade.img.gz > + IMAGE_SIZE := 3776m > + IMAGE/sysupgrade.img.gz := karo-boot-img | karo-sdcard-img | check-size > $$$$(IMAGE_SIZE) | gzip | append-metadata > + IMAGE/factory.img.gz := karo-boot-img | karo-sdcard-img | check-size > $$$$(IMAGE_SIZE) | gzip > +endef > +TARGET_DEVICES += tx6u-8033 > + > $(eval $(call BuildImage)) > diff --git a/target/linux/imx6/image/gen_karo_sdcard_img.sh > b/target/linux/imx6/image/gen_karo_sdcard_img.sh > new file mode 100755 > index 0000000000..362ce5838b > --- /dev/null > +++ b/target/linux/imx6/image/gen_karo_sdcard_img.sh > @@ -0,0 +1,26 @@ > +#!/usr/bin/env bash > + > +set -x > +[ $# -eq 5 ] || { > + echo "SYNTAX: $0 <file> <bootfs image> <rootfs image> <bootfs size> > <rootfs size>" > + exit 1 > +} > + > +OUTPUT="$1" > +BOOTFS="$2" > +ROOTFS="$3" > +BOOTFSSIZE="$4" > +ROOTFSSIZE="$5" > + > +head=4 > +sect=63 > + > +set `ptgen -o $OUTPUT -h $head -s $sect -l 4096 -t 83 -S 0x0cc66cc0 -p > ${BOOTFSSIZE}M -t 83 -p ${ROOTFSSIZE}M` > + > +BOOTOFFSET="$(($1 / 512))" > +BOOTSIZE="$(($2 / 512))" > +ROOTFSOFFSET="$(($3 / 512))" > +ROOTFSSIZE="$(($4 / 512))" > + > +dd bs=512 if="$BOOTFS" of="$OUTPUT" seek="$BOOTOFFSET" conv=notrunc > +dd bs=512 if="$ROOTFS" of="$OUTPUT" seek="$ROOTFSOFFSET" conv=notrunc > diff --git a/target/linux/imx6/patches-4.14/100-bootargs.patch > b/target/linux/imx6/patches-4.14/100-bootargs.patch > index 0954391203..6c025e15db 100644 > --- a/target/linux/imx6/patches-4.14/100-bootargs.patch > +++ b/target/linux/imx6/patches-4.14/100-bootargs.patch > @@ -1,3 +1,16 @@ > +--- a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts > ++++ b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts > +@@ -51,6 +51,10 @@ > + display = &display; > + }; > + > ++ chosen { > ++ bootargs = "console=ttymxc0,115200"; > ++ }; > ++ > + backlight: backlight { > + compatible = "pwm-backlight"; > + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>; > --- a/arch/arm/boot/dts/imx6dl-wandboard.dts > +++ b/arch/arm/boot/dts/imx6dl-wandboard.dts > @@ -19,4 +19,8 @@ > diff --git a/tools/Makefile b/tools/Makefile > index 2f57d25525..034e54c5d9 100644 > --- a/tools/Makefile > +++ b/tools/Makefile > @@ -39,6 +39,7 @@ tools-$(BUILD_ISL) += isl > tools-$(CONFIG_USE_SPARSE) += sparse > tools-$(CONFIG_TARGET_apm821xx)$(CONFIG_TARGET_gemini) += genext2fs > tools-$(CONFIG_TARGET_tegra) += cbootimage cbootimage-configs > +tools-$(CONFIG_TARGET_imx6) += genext2fs
The target for genext2fs is already specified, merge it with previous definition. > > # builddir dependencies > $(curdir)/bison/compile := $(curdir)/flex/compile > Regards -- TMN _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel