The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped automatically by the mailing list software.
--- Begin Message ---Hi Adrian, I tested the patches on the device. I sysupgraded from the current master and everything seems OK. - Partitions root@OpenWrt:~# cat /proc/mtd dev: size erasesize name mtd0: 00030000 00001000 "u-boot" mtd1: 00010000 00001000 "u-boot-env" mtd2: 00010000 00001000 "factory" mtd3: 00010000 00001000 "factory5g" mtd4: 00010000 00001000 "Wolf_Config" mtd5: 00080000 00001000 "MyDlink" mtd6: 00080000 00001000 "Jffs2" mtd7: 00690000 00001000 "firmware" mtd8: 00198a90 00001000 "kernel" mtd9: 004f7570 00001000 "rootfs" mtd10: 001d4000 00001000 "rootfs_data" - Button codes OK both - No missing functionalities I noticed, however, that the green "Internet" LED blinks to the LAN4 port, while -I guess- it should blink to the INTERNET (wan/eth0.2) port. But this was already happening before, it's not related to your patch. Roger El 27/2/20 a les 14:46, Adrian Schmutzler ha escrit: > This patch addresses several issues for D-Link DIR-810L: > > - add correct button codes > - harmonize button node names > - use generic flash@0 > - remove unused pin groups from state_default > - improve sorting of properties > > The patch is only build-tested. > > Signed-off-by: Adrian Schmutzler <[email protected]> > > --- > > If somebody owns this device, I'd be delighted about a test of both patches > in general as well as if somebody would test if higher SPI frequency is > possible. > > --- > .../ramips/dts/mt7620a_dlink_dir-810l.dts | 18 ++++++++++-------- > 1 file changed, 10 insertions(+), 8 deletions(-) > > diff --git a/target/linux/ramips/dts/mt7620a_dlink_dir-810l.dts > b/target/linux/ramips/dts/mt7620a_dlink_dir-810l.dts > index 0b1ca26ba4..514e9cc354 100644 > --- a/target/linux/ramips/dts/mt7620a_dlink_dir-810l.dts > +++ b/target/linux/ramips/dts/mt7620a_dlink_dir-810l.dts > @@ -23,20 +23,20 @@ > reset { > label = "reset"; > gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; > - linux,code = <BTN_0>; > + linux,code = <KEY_RESTART>; > }; > > wps { > label = "wps"; > gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; > - linux,code = <BTN_0>; > + linux,code = <KEY_WPS_BUTTON>; > }; > }; > > leds { > compatible = "gpio-leds"; > > - led_power_green: power { > + led_power_green: power_green { > label = "dir-810l:green:power"; > gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; > }; > @@ -46,7 +46,7 @@ > gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; > }; > > - power2 { > + power_orange { > label = "dir-810l:orange:power"; > gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; > }; > @@ -56,7 +56,7 @@ > &spi0 { > status = "okay"; > > - m25p80@0 { > + flash@0 { > compatible = "jedec,spi-nor"; > reg = <0>; > spi-max-frequency = <10000000>; > @@ -119,7 +119,7 @@ > > &state_default { > gpio { > - ralink,group = "mdio", "rgmii1", "i2c", "wled", "uartf"; > + ralink,group = "i2c", "uartf"; > ralink,function = "gpio"; > }; > }; > @@ -130,9 +130,10 @@ > }; > > &gsw { > - mediatek,port4 = "ephy"; > pinctrl-names = "default"; > pinctrl-0 = <&ephy_pins>; > + > + mediatek,port4 = "ephy"; > }; > > &pcie { > @@ -140,9 +141,10 @@ > }; > > &wmac { > - ralink,mtd-eeprom = <&factory 0x0>; > pinctrl-names = "default"; > pinctrl-0 = <&pa_pins>; > + > + ralink,mtd-eeprom = <&factory 0x0>; > mtd-mac-address = <&factory 0x28>; > }; >
--- End Message ---
_______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
