Hi, > -----Original Message----- > From: openwrt-devel [mailto:[email protected]] > On Behalf Of Tomasz Maciej Nowak > Sent: Montag, 4. Mai 2020 19:49 > To: [email protected] > Subject: [OpenWrt-Devel] [19.07] [PATCH] ath79: add support for Sitecom > WLR-7100 > > Backported from: 1bc921f419df508c57dc07cd3e43cdf0408c17dd
Device support is typically not backported to stable branches, unless you have a very good reason for it. Best Adrian > > Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless > router. > > Specification > SoC: Atheros AR1022 > RAM: 64 MB DDR2 > Flash: 8 MB SPI NOR > WIFI: 2.4 GHz 2T2R integrated > 5 GHz 2T2R QCA9882 integrated (connected to PCIe lane) > Ethernet: 5x 10/100/1000 Mbps QCA8337N > USB: 1x 2.0 > LEDS: 4x GPIO controlled, 5x switch > Buttons: 2x GPIO controlled > UART: row of 4 unpopulated holes near USB port, starting count from > white triangle on PCB > 1. VCC 3.3V, 2. GND, 3. TX, 4. RX > baud: 115200, parity: none, flow control: none > > Installation > 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router > configuration interface, 3. Go to Toolbox > Firmware, 4. Browse for OpenWrt > factory image with dlf extension and hit Apply, 5. Wait few minutes, after the > Power LED will stop blinking, the router > is ready for configuration. > > Known issues > 5GHz LED doesn't work > > Additional information > When TX line on UART is connected, and board is switched on from power > off state, the DDR memory training may fail. > If connected to UART, when prompted for number on boot, one can enter > number 4 to open bootloader (U-Boot) command line. > OEM firmware shell password is: SitecomSenao useful for creating backup of > original firmware. > There is also another revision of this device (v1 001), which may or may not > work with introduced images. > > Signed-off-by: Tomasz Maciej Nowak <[email protected]> > --- > .../ath79/base-files/etc/board.d/02_network | 6 + > .../etc/hotplug.d/firmware/10-ath9k-eeprom | 3 +- > .../etc/hotplug.d/firmware/11-ath10k-caldata | 3 +- > .../ath79/dts/ar1022_sitecom_wlr-7100.dts | 171 ++++++++++++++++++ > target/linux/ath79/image/generic.mk | 12 ++ > 5 files changed, 193 insertions(+), 2 deletions(-) create mode 100644 > target/linux/ath79/dts/ar1022_sitecom_wlr-7100.dts > > diff --git a/target/linux/ath79/base-files/etc/board.d/02_network > b/target/linux/ath79/base-files/etc/board.d/02_network > index 1b0e76b1593b..d494c0144725 100755 > --- a/target/linux/ath79/base-files/etc/board.d/02_network > +++ b/target/linux/ath79/base-files/etc/board.d/02_network > @@ -150,6 +150,7 @@ ath79_setup_interfaces() > iodata,wn-ac1600dgr2|\ > iodata,wn-ag300dgr|\ > pcs,cr5000|\ > + sitecom,wlr-7100|\ > wd,mynet-n750) > ucidef_add_switch "switch0" \ > "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" > @@ -349,6 +350,11 @@ ath79_setup_macs() > wan_mac=$(mtd_get_mac_binary factory 0) > lan_mac=$(macaddr_setbit_la "$wan_mac") > ;; > + sitecom,wlr-7100) > + lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr) > + wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr) > + label_mac=$lan_mac > + ;; > tplink,archer-a7-v5|\ > tplink,archer-c7-v4|\ > tplink,archer-c7-v5|\ > diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k- > eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k- > eeprom > index d85e90f10683..69ffad1a99ef 100644 > --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k- > eeprom > +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eepr > +++ om > @@ -119,7 +119,8 @@ case "$FIRMWARE" in > iodata,wn-ac1167dgr|\ > iodata,wn-ac1600dgr|\ > iodata,wn-ac1600dgr2|\ > - iodata,wn-ag300dgr) > + iodata,wn-ag300dgr|\ > + sitecom,wlr-7100) > ath9k_eeprom_extract "art" 4096 1088 > ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env > ethaddr) 2 > ;; > diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k- > caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k- > caldata > index d93e6dcd71ab..5b29ad0ce9fc 100644 > --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k- > caldata > +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-cal > +++ data > @@ -109,7 +109,8 @@ case "$FIRMWARE" in > ;; > engenius,epg5000|\ > iodata,wn-ac1167dgr|\ > - iodata,wn-ac1600dgr2) > + iodata,wn-ac1600dgr2|\ > + sitecom,wlr-7100) > ath10kcal_extract "art" 20480 2116 > ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii > u-boot-env ethaddr) +1) > ;; > diff --git a/target/linux/ath79/dts/ar1022_sitecom_wlr-7100.dts > b/target/linux/ath79/dts/ar1022_sitecom_wlr-7100.dts > new file mode 100644 > index 000000000000..8a70b597b0fe > --- /dev/null > +++ b/target/linux/ath79/dts/ar1022_sitecom_wlr-7100.dts > @@ -0,0 +1,171 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +#include "ar9344.dtsi" > + > +/ { > + model = "Sitecom WLR-7100 v1 002 (X7 AC1200)"; > + compatible = "sitecom,wlr-7100", "qca,ar9344"; > + > + aliases { > + led-boot = &power; > + led-failsafe = &power; > + led-running = &power; > + led-upgrade = &power; > + }; > + > + keys { > + compatible = "gpio-keys"; > + > + wlan2g { > + label = "2.4GHz"; > + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_RESTART>; > + }; > + > + wlan5g { > + label = "5GHz"; > + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_WPS_BUTTON>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + ops { > + label = "wlr-7100:white:ops"; > + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; > + }; > + > + power: power { > + label = "wlr-7100:amber:power"; > + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; > + default-state = "on"; > + }; > + > + wlan2g { > + label = "wlr-7100:blue:wlan2g"; > + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; > + linux,default-trigger = "phy1tpt"; > + }; > + }; > +}; > + > +ð0 { > + status = "okay"; > + > + pll-data = <0x06000000 0x00000101 0x00001616>; > + > + phy-mode = "rgmii"; > + phy-handle = <&phy0>; > + > + gmac-config { > + device = <&gmac>; > + rgmii-gmac0 = <1>; > + }; > +}; > + > +&mdio0 { > + status = "okay"; > + > + phy0: ethernet-phy@0 { > + reg = <0>; > + phy-mode = "rgmii"; > + > + qca,ar8327-initvals = < > + 0x04 0x87a00000 /* PORT0 PAD Mode */ > + 0x0c 0x01000000 /* PORT6 PAD Mode */ > + 0x10 0x80000000 /* PWS_REG_VALUE */ > + 0x7c 0x000000fe /* PORT0_STATUS */ > + 0x94 0x000000fe /* PORT6_STATUS */ > + >; > + }; > +}; > + > +&pcie { > + status = "okay"; > + > + wifi@0,0 { > + compatible = "qcom,ath10k"; > + reg = <0x0000 0 0 0 0>; > + }; > +}; > + > +&ref { > + clock-frequency = <25000000>; > +}; > + > +&spi { > + num-cs = <1>; > + status = "okay"; > + > + flash@0 { > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <25000000>; > + > + partitions { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "u-boot"; > + reg = <0x000000 0x030000>; > + read-only; > + }; > + > + uenv: partition@30000 { > + label = "u-boot-env"; > + reg = <0x030000 0x010000>; > + read-only; > + }; > + > + partition@40000 { > + compatible = "denx,uimage"; > + label = "firmware"; > + reg = <0x040000 0x750000>; > + }; > + > + partition@790000 { > + label = "backup"; > + reg = <0x790000 0x010000>; > + read-only; > + }; > + > + partition@7a0000 { > + label = "storage"; > + reg = <0x7a0000 0x050000>; > + read-only; > + }; > + > + art: partition@7f0000 { > + label = "art"; > + reg = <0x7f0000 0x010000>; > + read-only; > + }; > + }; > + }; > +}; > + > +&uart { > + status = "okay"; > +}; > + > +&usb { > + status = "okay"; > +}; > + > +&usb_phy { > + status = "okay"; > +}; > + > +&wmac { > + status = "okay"; > + > + qca,no-eeprom; > +}; > diff --git a/target/linux/ath79/image/generic.mk > b/target/linux/ath79/image/generic.mk > index 55053be34f11..550f24f45c8b 100644 > --- a/target/linux/ath79/image/generic.mk > +++ b/target/linux/ath79/image/generic.mk > @@ -674,6 +674,18 @@ define Device/rosinson_wr818 endef > TARGET_DEVICES += rosinson_wr818 > > +define Device/sitecom_wlr-7100 > + ATH_SOC := ar1022 > + DEVICE_TITLE := Sitecom WLR-7100 v1 002 > + DEVICE_PACKAGES := ath10k-firmware-qca988x-ct > +kmod-ath10k-ct-smallbuffers kmod-usb2 > + IMAGES += factory.dlf > + IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \ > + append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \ > + senao-header -r 0x222 -p 0x53 -t 2 > + IMAGE_SIZE := 7488k > +endef > +TARGET_DEVICES += sitecom_wlr-7100 > + > define Device/wd_mynet-n750 > $(Device/seama) > ATH_SOC := ar9344 > -- > 2.26.2 > > > _______________________________________________ > openwrt-devel mailing list > [email protected] > https://lists.openwrt.org/mailman/listinfo/openwrt-devel
openpgp-digital-signature.asc
Description: PGP signature
_______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
