On Mon, May 25, 2020 at 05:05:16PM -0700, Heppler, J. Scott wrote: > > * MediaTek MT7620A (580 Mhz) > * 8 MB of FLASH > * 64 MB of RAM > * 2.4Ghz and 5.0Ghz radios both now functional > * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) > * UART header on PCB (57600 8n1) > * Green/Orange Power LEDs illuminating a Power-Button Lens > Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet > Lens > * 3x button - wps, power and reset > * U-boot bootloader > > Installation: > > The sysupgrade.bin image is reported to be OEM web flashed with an > ncc_att_hwid > appended. ncc_att_hwid is a 32bit binary in the GPL Source download for > either > the TEW-810DR or DIR-810L and is located at > source/user/wolf/cameo/ncc/hostTools. > The invocation is: ncc_att_hwid > -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0" > This may need to be altered if your hardware version is "1.1R". > The image can also be directly flashed via serial tftp. > 1. Load *.sysupgrade.bin to your tftp server directory and rename for > convenience. > 2. Set a static ip 192.168.10.100. > 3. NIC cable to a lan port. > 4. Serial connection parameters 57600,8N1 > 5. Power on the TEW-810 and press 4 for a u-boot command line prompt. > 6. Verify IP's with U-Boot command "printenv". > 7. Adjust tftp settings if needed per the tftp documentation > 8. Boot the tftp image to test the build. > 9. If the image loads, reset your server ip to 192.168.1.10 and restart > network. > 10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image. > > Signed-off-by: J. Scott Heppler <shep...@centurylink.net> > > Summary v4 -> v5 > 1. Enumerated installation steps and corrected grammar. > 2. Added SPDX License Identifier to *.dts. > 3. gpio-keys-polled -> gpio-keys in *.dts. > 4. gpio2 0 is actually behind a Globe/Internet lens - changed to wan. > 5. Increased spi-max-frequency 10000000 -> 50000000 > 6. jffs2 partition 0xe0000 -> 0xf0000. > 7. &state_default groups dropped mdio, rgmii1, wled. > 8. MAC assignments mirror DIR-810L and verify in Luci. Unchanged > 02_network and *.dts. > 9. 01_leds changed consistent with #4. > 10. Removed SUPPORTED_DEVICES from image/mt7620.mk. Note: the D-Link > DIR-810L has the same SUPPORTED_DEVICES entry in image/mt7620.mk. > 11. Builds/Runs on my test Device. > --- > .../ramips/dts/mt7620a_trendnet_tew-810dr.dts | 166 ++++++++++++++++++ > target/linux/ramips/image/mt7620.mk | 9 + > .../mt7620/base-files/etc/board.d/01_leds | 3 + > .../mt7620/base-files/etc/board.d/02_network | 8 +- > 4 files changed, 183 insertions(+), 3 deletions(-) > create mode 100644 target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts > > diff --git a/target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts > b/target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts > new file mode 100644 > index 0000000000..5012d39b51 > --- /dev/null > +++ b/target/linux/ramips/dts/mt7620a_trendnet_tew-810dr.dts > @@ -0,0 +1,166 @@ > +//SPDX-License-Identifier: GPL-2.0-or-later OR MIT > +/dts-v1/; > + > +#include "mt7620a.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +/ { > + compatible = "trendnet,tew-810dr", "ralink,mt7620a-soc"; > + model = "TRENDnet TEW-810DR"; > + > + aliases { > + led-boot = &led_power_green; > + led-failsafe = &led_power_green; > + led-running = &led_power_green; > + led-upgrade = &led_power_green; > + label-mac-device = ðernet; > + }; > + > + keys { > + compatible = "gpio-keys"; > + > + reset { > + label = "reset"; > + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_RESTART>; > + }; > + > + wps { > + label = "wps"; > + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_WPS_BUTTON>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led_power_green: power_green { > + label = "tew-810dr:green:power"; > + gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; > + }; > + > + wan_orange: wan_orange { > + label = "tew-810dr:orange:wan"; > + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; > + }; > + > + wan_green: wan_green { > + label = "tew-810dr:green:wan"; > + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; > + }; > + > + led_power_orange { > + label = "tew-810dr:orange:power"; > + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; > + }; > + }; > +}; > + > +&spi0 { > + status = "okay"; > + > + flash@0 { > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <50000000>; > + > + partitions { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "u-boot"; > + reg = <0x0 0x30000>; > + read-only; > + }; > + > + partition@30000 { > + label = "u-boot-env"; > + reg = <0x30000 0x10000>; > + read-only; > + }; > + > + factory: partition@40000 { > + label = "factory"; > + reg = <0x40000 0x10000>; > + read-only; > + }; > + > + factory5g: partition@50000 { > + label = "factory5g"; > + reg = <0x50000 0x10000>; > + read-only; > + }; > + > + partition@60000 { > + label = "Wolf_Config"; > + reg = <0x60000 0x10000>; > + read-only; > + }; > + > + partition@70000 { > + label = "MyDlink"; > + reg = <0x70000 0x80000>; > + read-only; > + }; > + > + partition@f0000 { > + label = "Jffs2"; > + reg = <0xf0000 0x80000>; > + read-only; > + }; > + > + partition@170000 { > + compatible = "denx,uimage"; > + label = "firmware"; > + reg = <0x170000 0x690000>; > + }; > + }; > + }; > +}; > + > +&state_default { > + gpio { > + groups = "i2c", "uartf", "ephy"; > + function = "gpio"; > + }; > +}; > + > +ðernet { > + mtd-mac-address = <&factory 0x28>; > + mediatek,portmap = "llllw"; > +}; > + > +&gsw { > + mediatek,port4 = "ephy"; > +}; > + > +&pcie { > + status = "okay"; > +}; > + > +&wmac { > + pinctrl-names = "default"; > + pinctrl-0 = <&pa_pins>; > + > + ralink,mtd-eeprom = <&factory 0x0>;
white-space is odd here, please fix that and use tab like for the other properties. > + mtd-mac-address = <&factory 0x28>; > +}; > + > +&pcie0 { > + wifi@0,0 { > + reg = <0x0000 0 0 0 0>; > + mediatek,mtd-eeprom = <&factory 0x8000>; > + ieee80211-freq-limit = <5000000 6000000>; > + mtd-mac-address = <&factory 0x28>; > + mtd-mac-address-increment = <2>; > + }; > +}; > + > +&gpio2 { > + status = "okay"; > +}; > diff --git a/target/linux/ramips/image/mt7620.mk > b/target/linux/ramips/image/mt7620.mk > index e435b1d15f..386809e40f 100644 > --- a/target/linux/ramips/image/mt7620.mk > +++ b/target/linux/ramips/image/mt7620.mk > @@ -1005,6 +1005,15 @@ define Device/tplink_re210-v1 > endef > TARGET_DEVICES += tplink_re210-v1 > +define Device/trendnet_tew-810dr > + SOC := mt7620a > + DEVICE_PACKAGES := kmod-mt76x0e > + DEVICE_VENDOR := TRENDnet > + DEVICE_MODEL := TEW-810DR > + IMAGE_SIZE := 6720k > +endef > +TARGET_DEVICES += trendnet_tew-810dr > + > define Device/vonets_var11n-300 > SOC := mt7620n > IMAGE_SIZE := 3776k > diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds > b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds > index c1deae59e3..595f84f5d2 100755 > --- a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds > +++ b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds > @@ -191,6 +191,9 @@ tplink,archer-mr200) > tplink,re200-v1) > ucidef_set_led_netdev "lan" "lan" "$boardname:green:lan" "eth0" > ;; > +trendnet,tew-810dr) > + ucidef_set_led_netdev "wan" "wan" "$boardname:green:wan" "eth0.2" > "link tx rx" > + ;; and here as well. please use tabs instead of spaces to be consistent with the rest of the file. > youku,yk1) > set_wifi_led "$boardname:blue:air" > ucidef_set_led_switch "wan" "wan" "$boardname:blue:wan" "switch0" "0x10" > diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network > b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network > index d024674c10..3fc0ce3049 100755 > --- a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network > +++ b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network > @@ -26,6 +26,7 @@ ramips_setup_interfaces() > ralink,mt7620a-mt7610e-evb|\ > ralink,mt7620a-v22sg-evb|\ > sanlinking,d240|\ > + trendnet,tew-810dr|\ > youku,yk1|\ > zbtlink,zbt-ape522ii|\ > zbtlink,zbt-we826-16m|\ > @@ -259,9 +260,10 @@ ramips_setup_macs() > alfa-network,ac1200rm|\ > dlink,dir-810l|\ > phicomm,psg1218a|\ > - phicomm,psg1218b) > - wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x28)" 1) > - ;; > + phicomm,psg1218b|\ > + trendnet,tew-810dr) > + wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x28)" 1) > + ;; and here. > alfa-network,r36m-e4g|\ > zbtlink,zbt-we1026-h-32m) > wan_mac=$(mtd_get_mac_binary factory 0x2e) > -- > 2.20.1 lgtm apart from than the white-space issues. Cheers Daniel > > > -- > J. Scott Heppler > > _______________________________________________ > openwrt-devel mailing list > openwrt-devel@lists.openwrt.org > https://lists.openwrt.org/mailman/listinfo/openwrt-devel _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel