TP-Link has developed a number of access points based on the AP152
reference board. In the EAP-series of 802.11ac access points, this
includes the following devices with one ethernet port:
* EAP225 v1/v2
* EAP225 v3
* EAP225-Outdoor v1
* EAP245 v1
Since the only differences between these devices are the ath10k wireless
radios and LEDs, a common base is provided for the overlapping support
requirements.
Hardware commonalities:
* SoC: QCA9563-AL3A MIPS 74kc v5.0 @ 775MHz, AHB @ 258MHz
* RAM: 128MiB DDR2 @ 650MHz
* Flash: 16MiB SPI NOR
* Wi-Fi 2.4GHz: provided by SoC
* Wi-Fi 5Ghz: ath10k chip on PCIe
* Ethernet: AR8033-AL1A, one 1GbE port (802.3at PoE)
Signed-off-by: Sander Vanheule <san...@svanheule.net>
---
.../dts/qca9563_tplink_eap2x5-1port.dtsi | 135 ++++++++++++++++++
1 file changed, 135 insertions(+)
create mode 100644 target/linux/ath79/dts/qca9563_tplink_eap2x5-1port.dtsi
diff --git a/target/linux/ath79/dts/qca9563_tplink_eap2x5-1port.dtsi
b/target/linux/ath79/dts/qca9563_tplink_eap2x5-1port.dtsi
new file mode 100644
index 0000000000..4c550fff6e
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_eap2x5-1port.dtsi
@@ -0,0 +1,135 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ aliases {
+ label-mac-device = ð0;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&uart {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x020000>;
+ read-only;
+ };
+
+ partition@20000 {
+ label = "partition-table";
+ reg = <0x020000 0x010000>;
+ read-only;
+ };
+
+ info: partition@30000 {
+ label = "info";
+ reg = <0x030000 0x010000>;
+ read-only;
+ };
+
+ partition@40000 {
+ compatible = "openwrt,elf";
+ label = "firmware";
+ reg = <0x040000 0xd80000>;
+ };
+
+ partition@dc0000 {
+ label = "config";
+ reg = <0xdc0000 0x030000>;
+ read-only;
+ };
+
+ /* df0000-f30000 undefined in vendor firmware */
+
+ partition@f30000 {
+ label = "log";
+ reg = <0xf30000 0x0c0000>;
+ read-only;
+ };
+
+ art: partition@ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&pinmux {
+ mdio_pins: mdio_pins {
+ /* GPIO 10 as MDIO(0x20), GPIO 8 as MDC(0x21) */
+ pinctrl-single,bits = <0x8 0x00200021 0x00ff00ff>;
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ phy-mask = <0x10>;
+
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&phy4>;
+ phy-mode = "sgmii";
+
+ mtd-mac-address = <&info 0x8>;
+
+ qca956x-serdes-fixup;
+
+ gmac-config {
+ device = <&gmac>;
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&info 0x8>;
+};
--
2.26.2
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
