On 1/24/21 5:20 PM, Todor Colov wrote:
Signed-off-by: Todor Colov <[email protected]>
Please add a description.
---
.../ipq806x/base-files/etc/board.d/01_leds | 3 +
.../ipq806x/base-files/etc/board.d/02_network | 1 +
.../base-files/lib/upgrade/platform.sh | 3 +-
.../arm/boot/dts/qcom-ipq8064-e8350-v1.dts | 246 ++++++++++++++++++
target/linux/ipq806x/image/Makefile | 29 +++
.../0069-arm-boot-add-dts-files.patch | 3 +-
6 files changed, 283 insertions(+), 2 deletions(-)
create mode 100644
target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-e8350-v1.dts
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds
b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index 284f9e2c1d..33c7f80fb9 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -22,6 +22,9 @@ edgecore,ecw5410)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy1tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy0tpt"
;;
+linksys,e8350-v1)
+ ucidef_set_led_wlan "wlan" "WLAN" "green:wifi" "phy0tpt"
+ ;;
nec,wg2600hp)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy1tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy0tpt"
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network
b/target/linux/ipq806x/base-files/etc/board.d/02_network
index ddef4b7ac6..036cba2de5 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -69,6 +69,7 @@ qcom,ipq8064-db149)
ubnt,unifi-ac-hd)
ucidef_set_interface_lan "eth0 eth1"
;;
+linksys,e8350-v1 |\
Please add this alphabetical ordered.
zyxel,nbg6817) hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr) ucidef_add_switch "switch0" \ diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 4dc612492c..7b319a5b7c 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -1,7 +1,7 @@ PART_NAME=firmware REQUIRE_IMAGE_METADATA=1-RAMFS_COPY_BIN='fw_printenv fw_setenv'+RAMFS_COPY_BIN='fw_printenv fw_setenv fwtool'
Why is fwtool added?
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'platform_check_image() {@@ -20,6 +20,7 @@ platform_do_upgrade() { nand_do_upgrade "$1" ;; compex,wpq864|\ + linksys,e8350-v1|\ netgear,d7800 |\ netgear,r7500 |\ netgear,r7500v2 |\ diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-e8350-v1.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-e8350-v1.dts new file mode 100644 index 0000000000..872deeb044 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-e8350-v1.dts @@ -0,0 +1,246 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +#include "qcom-ipq8064-v2.0.dtsi" + +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + model = "Linksys E8350 V1 WiFi Router"; + compatible = "linksys,e8350-v1", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + aliases { + serial0 = &gsbi4_serial; + + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = <KEY_WPS_BUTTON>; + }; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RFKILL>; + }; + }; + + nand-controller@1ac00000 { + compatible = "qcom,ipq806x-nand"; + reg = <0x1ac00000 0x800>; + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; + + nand@0 { + reg = <0>; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + + partition@0 { + label = "ubi"; + reg = <0 0x4000000>; + }; + + partition@4000000 { + label = "extra"; + reg = <0x4000000 0x4000000>; + }; + }; + }; + }; + + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_power: power { + label = "green:power"; + gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + wps { + label = "green:wps"; + gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; + }; + + wifi { + label = "green:wifi"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio68","gpio65", "gpio67"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio26","gpio53", "gpio54"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; +}; + +&gsbi4 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "okay"; + serial@16340000 { + status = "okay"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ +}; +&gsbi5 { + qcom,mode = <GSBI_PROT_SPI>; + status = "okay"; + + spi5: spi@1a280000 { + status = "okay"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + m25p80@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <51200000>; + reg = <0>; + + partitions { + compatible = "qcom,smem"; + }; + }; + }; +}; + +&sata_phy { + status = "okay"; +}; + +&sata { + status = "okay"; +}; + +&usb3_0 { + clocks = <&gcc USB30_1_MASTER_CLK>; + status = "okay"; +}; + +&usb3_1 { + clocks = <&gcc USB30_0_MASTER_CLK>; + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x00010 0x2613a0 /* PWS_REG */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac2 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <2>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&tcsr { + qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>; + compatible = "qcom,tcsr"; +}; + +&adm_dma { + status = "okay"; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index bab1da0090..5ea38f564d 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -23,6 +23,17 @@ define Build/edimax-header @mv [email protected] $@ endef+# tune addpattern for Linksys E8350-V1 fw pattern generation+define Build/linksys-bin + $(STAGING_DIR_HOST)/bin/addpattern -p $(FW_DEVICE_ID) -v $(FW_VERSION) $(if $(SERIAL),-s $(SERIAL)) -i $@ -o [email protected] + mv [email protected] $@ +endef +# Use Linksys fw header generator to upgrade openwrt factory image over the native Linksys WEB interface +define Build/linksys-addfwhdr + -$(STAGING_DIR_HOST)/bin/addfwhdr -i $@ -o [email protected] \ + ;mv "[email protected]" "$@" +endef + define Device/Default PROFILES := Default KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts) @@ -145,6 +156,24 @@ define Device/edgecore_ecw5410 endef TARGET_DEVICES += edgecore_ecw5410+define Device/linksys_e8350-v1+ $(call Device/LegacyImage) + DEVICE_VENDOR := Linksys + DEVICE_MODEL := E8350 + DEVICE_VARIANT := v1 + SOC := qcom-ipq8064 + FW_VERSION := v1.0.03.003 + FW_DEVICE_ID := 8350 + PAGESIZE := 2048 + BLOCKSIZE := 128k + KERNEL_IN_UBI := 1 + IMAGES = factory.bin sysupgrade.ubi + IMAGE/sysupgrade.ubi := append-ubi | check-size 0x04000000 | append-metadata
Is the sysupgrade.bin not working?
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
+ IMAGE/factory.bin := append-ubi | check-size 0x04000000 | linksys-addfwhdr | linksys-bin + DEVICE_PACKAGES := ath10k-firmware-qca988x-ct +endef +TARGET_DEVICES += linksys_e8350-v1 + define Device/linksys_ea7500-v1 $(call Device/LegacyImage) DEVICE_VENDOR := Linksys diff --git a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch index 055a4cbc30..df37f18f23 100644 --- a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <[email protected]>--- a/arch/arm/boot/dts/Makefile+++ b/arch/arm/boot/dts/Makefile -@@ -842,7 +842,24 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -842,7 +842,25 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4019-ap.dk04.1-c3.dtb \ qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ @@ -20,6 +20,7 @@ Signed-off-by: John Crispin <[email protected]> + qcom-ipq8064-d7800.dtb \ + qcom-ipq8064-db149.dtb \ + qcom-ipq8064-ap161.dtb \ ++ qcom-ipq8064-e8350-v1.dtb \ + qcom-ipq8064-ea7500-v1.dtb \ + qcom-ipq8064-ea8500.dtb \ + qcom-ipq8064-g10.dtb \
OpenPGP_0x93DD20630910B515.asc
Description: application/pgp-keys
OpenPGP_signature
Description: OpenPGP digital signature
_______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
