On 1/18/22 4:29 AM, Koen Vandeputte wrote:
Hi Ben,
After stress testing some wave 1 2x2 radios on multiple boards using openwrt
master I noticed this crash on 2 of them.
Any idea?
01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless
Network Adapter
Thanks,
Koen
[ 16.441327] ath10k 5.15 driver, optimized for CT firmware, probing pci
device: 0x3c.
[ 16.468523] ath10k_pci 0000:01:00.0: pci irq legacy oper_irq_mode 1 irq_mode
0 reset_mode 0
[ 17.719409] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id
0x043222ff sub 19b6:d042
[ 17.728819] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs
1 testmode 0
[ 17.740820] ath10k_pci 0000:01:00.0: firmware ver 10.1-ct-8x-__fH-022-ecad3248 api 2 features
wmi-10.x,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32
1b2a161c
[ 18.063728] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32
bebc7c08
[ 18.993270] ath10k_pci 0000:01:00.0: 10.1 wmi init: vdevs: 16 peers: 127
tid: 256
[ 19.011087] ath10k_pci 0000:01:00.0: wmi print 'P 128 V 8 T 410'
[ 19.017226] ath10k_pci 0000:01:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0
ct-sta: 0'
[ 19.025374] ath10k_pci 0000:01:00.0: wmi print 'alloc rem: 25000 iram: 38944'
[ 19.082086] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 2 htt-op 2 cal file
max-sta 128 raw 0 hwcrypto 1
[ 19.097374] ath10k_pci 0000:01:00.0: NOTE: Firmware DBGLOG output disabled
in debug_mask: 0x10000000
[ 19.228812] ath: EEPROM regdomain sanitized
[ 19.228825] ath: EEPROM regdomain: 0x64
[ 19.228830] ath: EEPROM indicates we should expect a direct regpair map
[ 19.228849] ath: Country alpha2 being used: 00
[ 19.228854] ath: Regpair used: 0x64
[ 19.282229] usbcore: registered new interface driver option
[ 19.288009] usbserial: USB Serial support registered for GSM modem (1-port)
[ 19.318937] usbcore: registered new interface driver qcserial
[ 19.324852] usbserial: USB Serial support registered for Qualcomm USB modem
[ 19.342601] qcserial 2-1:1.0: Qualcomm USB modem converter detected
[ 19.349298] usb 2-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 19.359080] qcserial 2-1:1.2: Qualcomm USB modem converter detected
[ 19.365777] usb 2-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 19.389826] qcserial 2-1:1.3: Qualcomm USB modem converter detected
[ 19.396484] usb 2-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 19.429616] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 26.341428] eth0: link up (1000Mbps/Full duplex)
[ 26.346711] br-wan: port 1(eth0) entered blocking state
[ 26.352077] br-wan: port 1(eth0) entered disabled state
[ 26.357631] device eth0 entered promiscuous mode
[ 26.375076] br-wan: port 1(eth0) entered blocking state
[ 26.380431] br-wan: port 1(eth0) entered forwarding state
[ 32.696768] ag71xx: max retries for SGMII fixup exceeded
[ 32.702172] eth1: link up (1000Mbps/Full duplex)
[ 32.727999] br-wan: port 2(eth1) entered blocking state
[ 32.733310] br-wan: port 2(eth1) entered disabled state
[ 32.738882] device eth1 entered promiscuous mode
[ 32.808555] br-wan: port 2(eth1) entered blocking state
[ 32.813867] br-wan: port 2(eth1) entered forwarding state
[ 37.660591] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
(null)
[ 85.293759] ath10k_pci 0000:01:00.0: 10.1 wmi init: vdevs: 16 peers: 127
tid: 256
[ 85.311655] ath10k_pci 0000:01:00.0: wmi print 'P 128 V 8 T 410'
[ 85.317869] ath10k_pci 0000:01:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0
ct-sta: 0'
[ 85.326004] ath10k_pci 0000:01:00.0: wmi print 'alloc rem: 25000 iram: 38944'
[ 85.398523] ath10k_pci 0000:01:00.0: pdev param 0 not supported by firmware
[ 85.413584] ath10k_pci 0000:01:00.0: rts threshold -1
[ 85.428114] device wlan0 entered promiscuous mode
[ 85.435115] device wlan0 left promiscuous mode
[ 5578.497296] ath10k_pci 0000:01:00.0: Failed to synchronize setup for vdev 0
restart 0: -145, will restart firmware
[ 5578.507831] ath10k_pci 0000:01:00.0: failed to start vdev 0 addr
00:00:00:00:00:00 on freq 5320: -145
[ 5578.518005] ath10k_pci 0000:01:00.0: firmware crashed! (guid
b696878d-15a0-434c-9d17-81052d629e31)
Firmware/hardware hung, so we faked a crash to restart it. I doubt I can do
anything
to fix/improve this. I assume the radio's came back up OK after they crashed?
In general, wave-2 ath10k-ct seems more stable if you have a choice.
Thanks,
Ben
--
Ben Greear <gree...@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel