The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped automatically by the mailing list software.
--- Begin Message ---On Wed, 2022-12-28 at 23:11 +0300, Arınç ÜNAL wrote: > > The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access > > point distributed as Experia WiFi by KPN in the Netherlands. It > > features > > two ethernet ports and 2 internal antennas. > > > > Specifications > > -------------- > > SOC : Mediatek MT7621AT > > ETH : Two 1 gigabit ports, built into the SOC > > WIFI : MT7615DN > > BUTTON: Reset > > BUTTON: WPS > > LED : Power (green+red) > > LED : WiFi (green+blue) > > LED : WPS (green+red) > > LED : Followme (green+red) > > Power : 12 VDC, 1A barrel plug > > > > Winbond variant: > > RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM > > Flash : Winbond W25Q256JVFQ, 256Mb SPI > > U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1 > > > > Macronix variant: > > RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM > > Flash : MX25l25635FMI-10G, 256Mb SPI > > U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1 > > > > Serial > > ------ > > The serial port needs a TTL/RS-232 3V3 level converter! The Serial > > setting is 57600-8-N-1. The board has an unpopulated 2.54mm > > straight pin > > header. > > > > The pinout is: VCC (the square), RX, TX, GND. > > > > Installation > > ------------ > > 1. Open the device, take off the heat sink > > 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. > > Also > > connect the RESET pin for stability (thanks @FPSUsername for > > reporting) > > 3. Make a backup in case you want to revert to stock later > > 4. Flash the squashfs-factory.trx file to offset 0x50000 of the > > flash > > 5. Ensure the bootpartition variable is set to 0 in the U-Boot > > environment located at 0x30000 > > > > Note that the U-Boot is password protected, this can optionally be > > removed. See the forum for more details [1] > > > > MAC Addresses(stock) > > -------------------- > > +----------+------------------+-------------------+ > > > use | address | example | > > +----------+------------------+-------------------+ > > > Device | label | 00:00:00:11:00:00 | > > > Ethernet | + 3 | 00:00:00:11:00:03 | > > > 2g | + 0x020000f00001 | 02:00:00:01:00:01 | > > > 5g | + 1 | 00:00:00:11:00:01 | > > +----------+------------------+-------------------+ > > > > The label address is stored in ASCII in the board_data partition > > > > Known issues > > ------------ > > - 2g MAC address does not match stock due to missing support for > > that in > > macaddr_add > > - Only the power LED is configured by default > > > > References > > ---------- > > [1] > > https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653?u=harm > > > > Signed-off-by: Harm Berntsen <[email protected]> > > --- > > package/boot/uboot-envtools/files/ramips | 3 + > > .../dts/mt7621_arcadyan_we420223-99.dts | 210 > > ++++++++++++++++++ > > target/linux/ramips/image/mt7621.mk | 25 +++ > > .../mt7621/base-files/etc/board.d/02_network | 8 + > > .../etc/hotplug.d/ieee80211/10_fix_wifi_mac | 9 + > > .../mt7621/base-files/lib/upgrade/platform.sh | 1 + > > 6 files changed, 256 insertions(+) > > create mode 100644 > > target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts > > > > diff --git a/package/boot/uboot-envtools/files/ramips > > b/package/boot/uboot-envtools/files/ramips > > index f7f4821cef..8d4960e7a3 100644 > > --- a/package/boot/uboot-envtools/files/ramips > > +++ b/package/boot/uboot-envtools/files/ramips > > @@ -17,6 +17,9 @@ alfa-network,awusfree1|\ > > alfa-network,quad-e4g|\ > > alfa-network,r36m-e4g|\ > > alfa-network,tube-e4g|\ > > +arcadyan,we420223-99) > > + ubootenv_add_uci_config "/dev/mtd2" "0x0" "0x1000" "0x1000" > > + ;; > > engenius,esr600h|\ > > sitecom,wlr-4100-v1-002) > > ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x1000" > > diff --git a/target/linux/ramips/dts/mt7621_arcadyan_we420223- > > 99.dts b/target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts > > new file mode 100644 > > index 0000000000..f68d79af15 > > --- /dev/null > > +++ b/target/linux/ramips/dts/mt7621_arcadyan_we420223-99.dts > > @@ -0,0 +1,210 @@ > > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > > + > > +#include "mt7621.dtsi" > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/input/input.h> > > +#include <dt-bindings/leds/common.h> > > + > > +/ { > > + model = "Arcadyan WE420223-99"; > > + compatible = "arcadyan,we420223-99", "mediatek,mt7621-soc"; > > + > > + aliases { > > + led-boot = &led_power_green; > > + led-failsafe = &led_power_red; > > + led-running = &led_power_green; > > + led-upgrade = &led_wps_green; > > + led-wifi = &led_wifi_green; > > + }; > > + > > + chosen { > > + bootargs = "console=ttyS0,57600 ubi.mtd=5 > > root=/dev/ubiblock0_0"; > > + }; > > + > > + keys { > > + compatible = "gpio-keys"; > > + > > + reset { > > + label = "reset"; > > + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; > > + linux,code = <KEY_RESTART>; > > + }; > > + > > + wps { > > + label = "wps"; > > + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; > > + linux,code = <KEY_WPS_BUTTON>; > > + }; > > + }; > > + > > + leds { > > + compatible = "gpio-leds"; > > + > > + led_power_green: power_green { > > + label = "green:power"; > > + gpios = <&gpio 42 GPIO_ACTIVE_LOW>; > > + color = <LED_COLOR_ID_GREEN>; > > + function = LED_FUNCTION_POWER; > > + default-state = "on"; > > + }; > > + > > + led_power_red: power_red { > > + label = "red:power"; > > + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; > > + color = <LED_COLOR_ID_RED>; > > + function = LED_FUNCTION_FAULT; > > + }; > > + > > + led_wifi_blue: wifi_blue { > > + label = "blue:wifi"; > > + gpios = <&gpio 41 GPIO_ACTIVE_LOW>; > > + color = <LED_COLOR_ID_BLUE>; > > + function = LED_FUNCTION_WLAN; > > + }; > > + > > + led_wifi_green: wifi_green { > > + label = "green:wifi"; > > + gpios = <&gpio 43 GPIO_ACTIVE_LOW>; > > + color = <LED_COLOR_ID_GREEN>; > > + function = LED_FUNCTION_WLAN; > > + }; > > + > > + led_wps_red: wps_red { > > + label = "red:wps"; > > + gpios = <&gpio 45 GPIO_ACTIVE_LOW>; > > + color = <LED_COLOR_ID_RED>; > > + function = LED_FUNCTION_WPS; > > + }; > > + > > + led_wps_green: wps_green { > > + label = "green:wps"; > > + gpios = <&gpio 46 GPIO_ACTIVE_LOW>; > > + color = <LED_COLOR_ID_GREEN>; > > + function = LED_FUNCTION_WPS; > > + }; > > + > > + led_followme_r: followme_red { > > + label = "red:followme"; > > + gpios = <&gpio 47 GPIO_ACTIVE_LOW>; > > + color = <LED_COLOR_ID_RED>; > > + }; > > + > > + led_followme_g: followme_green { > > + label = "green:followme"; > > + gpios = <&gpio 48 GPIO_ACTIVE_LOW>; > > + color = <LED_COLOR_ID_GREEN>; > > + }; > > + }; > > +}; > > + > > +&spi0 { > > + status = "okay"; > > + > > + flash@0 { > > + compatible = "jedec,spi-nor"; > > + > > + reg = <0>; > > + spi-max-frequency = <70000000>; > > + > > + partitions { > > + compatible = "fixed-partitions"; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + partition@0 { > > + label = "ALL"; > > + reg = <0x0 0x2000000>; > > + read-only; > > + }; > > + > > + partition@1 { > > + label = "Bootloader"; > > + reg = <0x0 0x30000>; > > + read-only; > > + }; > > + > > + partition@30000 { > > + label = "Config"; > > + reg = <0x30000 0x10000>; > > + }; > > + > > + factory: partition@40000 { > > + label = "Factory"; > > + reg = <0x40000 0x10000>; > > + read-only; > > + }; > > + > > + partition@50000 { > > + label = "kernel"; > > + reg = <0x50000 0x1f60000>; > > + }; > > + > > + partition@490000 { > > + label = "rootfs"; > > + reg = <0x490000 0x1b20000>; > > + }; > > + > > + partition@1000000 { > > + label = "Kernel2"; > > + reg = <0x1000000 0xfb0000>; > > + }; > > + > > + partition@1440000 { > > + label = "RootFS2"; > > + reg = <0x1440000 0xb70000>; > > + }; > > + > > + partition@1fb0000 { > > + label = "glbcfg"; > > + reg = <0x1fb0000 0x10000>; > > + read-only; > > + }; > > + > > + partition@1fc0000 { > > + label = "board_data"; > > + reg = <0x1fc0000 0x10000>; > > + read-only; > > + }; > > + > > + partition@1fd0000 { > > + label = "glbcfg2"; > > + reg = <0x1fd0000 0x10000>; > > + read-only; > > + }; > > + > > + partition@1fe0000 { > > + label = "board_data2"; > > + reg = <0x1fe0000 0x10000>; > > + read-only; > > + }; > > + }; > > + }; > > +}; > > + > > +&xhci { > > + status = "disabled"; > > +}; > > + > > +&switch0 { > > + ports { > > + port@0 { > > + status = "okay"; > > + }; > > + > > + port@1 { > > + status = "okay"; > > Please define the label for the ports here. > > Arınç Thanks for reviewing Arınç. The mt7621.dtsi already contains the label "lan0" and "lan1" for these ports. On the outside[1] of the device the ports are simply named Ethernet. Shall I put a "lan0" and "lan1" label there? It felt a bit redundant to me so I did not put it in initially. Harm [1] https://openwrt.org/_detail/media/arcadyan/we420223-99_back.jpg
--- End Message ---
_______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
