#16752: WDR4900 with non-atheros 2.4GHz Wi-Fi adapter
-------------------------+-------------------------------------
Reporter: fcecamor | Owner: developers
Type: defect | Status: new
Priority: normal | Milestone: Barrier Breaker (trunk)
Component: base system | Version: Trunk
Keywords: |
-------------------------+-------------------------------------
Hi,
I flashed today the latest trunk r41062 on my new WDR4900 v. 1.3.
The first Wi-Fi adapter seem to not be the normal atheros of this router
but a '''RaLink Rt3352'''
After the configuration the 2.4GHz reduce speed and kick out all clients
with this errors:
{{{
[ 1482.998873] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 1484.045135] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 1484.990776] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 1506.321220] ath: phy1: Failed to stop TX DMA, queues=0x004!
}}}
Is the firmware trying to use the wrong driver ?
This is my dmesg:
{{{
[ 0.000000] Using Freescale P1014 machine description
[ 0.000000] Memory CAM mapping: 64/64 Mb, residual: 0Mb
[ 0.000000] Linux version 3.10.36 (openwrt@gb-13) (gcc version 4.8.3
(OpenWrt/Linaro GCC 4.8-2014.04 r41062) ) #1 Tue Jun 10 02:50:49 UTC 2014
[ 0.000000] Found legacy serial port 0 for /soc@ffe00000/serial@4500
[ 0.000000] mem=ffe04500, taddr=ffe04500, irq=0, clk=399999996,
speed=0
[ 0.000000] TL-WDR4900 v1 board from TP-Link
[ 0.000000] Top of RAM: 0x8000000, Total RAM: 0x8000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x07ffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat c03234a8, node_mem_map
c035c000
[ 0.000000] DMA zone: 256 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 32768 pages, LIFO batch:7
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536
bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 60572k/131072k available (3132k kernel code, 70500k
reserved, 116k data, 184k bss, 132k init)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffdf000..0xfffff000 : fixmap
[ 0.000000] * 0xfe000000..0xfe000000 : early ioremap
[ 0.000000] * 0xc9000000..0xfe000000 : vmalloc & ioremap
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] mpic: Resetting
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000,
max 1 CPUs
[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[ 0.000000] mpic: Initializing for 256 sources
[ 0.000000] time_init: decrementer frequency = 49.999999 MHz
[ 0.000000] time_init: processor frequency = 799.999992 MHz
[ 0.000000] clocksource: timebase mult[14000007] shift[24] registered
[ 0.000000] clockevent: decrementer mult[cccccc9] shift[32] cpu[0]
[ 0.000047] pid_max: default: 32768 minimum: 301
[ 0.000143] Mount-cache hash table entries: 512
[ 0.002630] NET: Registered protocol family 16
[ 0.008193] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware
bus number: 0->255
[ 0.008204] PCI host bridge /pcie@ffe09000 (primary) ranges:
[ 0.008213] MEM 0x00000000a0000000..0x00000000bfffffff ->
0x00000000a0000000
[ 0.008222] IO 0x00000000ffc10000..0x00000000ffc1ffff ->
0x0000000000000000
[ 0.008237] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[ 0.008582] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware
bus number: 0->255
[ 0.008591] PCI host bridge /pcie@ffe0a000 ranges:
[ 0.008600] MEM 0x0000000080000000..0x000000009fffffff ->
0x0000000080000000
[ 0.008608] IO 0x00000000ffc00000..0x00000000ffc0ffff ->
0x0000000000000000
[ 0.008622] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[ 0.020348] PCI: Probing PCI hardware
[ 0.020628] fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00
[ 0.020643] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.020653] pci_bus 0000:00: root bus resource [mem
0xa0000000-0xbfffffff]
[ 0.020674] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.020686] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to ff
[ 0.020719] pci 0000:00:00.0: [1957:012b] type 01 class 0x0b2000
[ 0.020733] pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match
header type 01)
[ 0.020766] pci 0000:00:00.0: supports D1 D2
[ 0.020775] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.021158] pci 0000:01:00.0: [168c:0033] type 00 class 0x028000
[ 0.021189] pci 0000:01:00.0: reg 10: [mem 0xa0000000-0xa001ffff 64bit]
[ 0.021229] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 0.021269] pci 0000:01:00.0: supports D1
[ 0.021277] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 0.028129] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.028146] pci 0000:00:00.0: bridge window [mem
0xa0000000-0xa00fffff]
[ 0.028204] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.028218] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.028387] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02
[ 0.028403] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff]
(bus address [0x0000-0xffff])
[ 0.028413] pci_bus 0001:02: root bus resource [mem
0x80000000-0x9fffffff]
[ 0.028424] pci_bus 0001:02: root bus resource [bus 02-ff]
[ 0.028435] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to ff
[ 0.028467] pci 0001:02:00.0: [1957:012b] type 01 class 0x0b2000
[ 0.028478] pci 0001:02:00.0: ignoring class 0x0b2000 (doesn't match
header type 01)
[ 0.028505] pci 0001:02:00.0: supports D1 D2
[ 0.028514] pci 0001:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.028706] pci 0001:02:00.0: Primary bus is hard wired to 0
[ 0.028719] pci 0001:02:00.0: bridge configuration invalid ([bus
01-01]), reconfiguring
[ 0.028890] pci 0001:03:00.0: [168c:abcd] type 00 class 0x020000
[ 0.028900] pci 0001:03:00.0: AR9381 fixup applied
[ 0.028924] pci 0001:03:00.0: reg 10: [mem 0x80000000-0x8001ffff 64bit]
[ 0.028964] pci 0001:03:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 0.029003] pci 0001:03:00.0: supports D1
[ 0.029012] pci 0001:03:00.0: PME# supported from D0 D1 D3hot
[ 0.036141] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.036157] pci 0001:02:00.0: bridge window [mem
0x80000000-0x800fffff]
[ 0.036208] pci_bus 0001:03: busn_res: [bus 03-ff] end is updated to 03
[ 0.036222] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to 03
[ 0.036265] PCI 0000:00 Cannot reserve Legacy IO [io 0x0000-0x0fff]
[ 0.036273] PCI 0001:02 Cannot reserve Legacy IO [io 0x20000-0x20fff]
[ 0.036301] pci 0000:00:00.0: BAR 9: can't assign mem pref (size
0x100000)
[ 0.036315] pci 0000:01:00.0: BAR 6: assigned [mem
0xa0020000-0xa002ffff pref]
[ 0.036325] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.036335] pci 0000:00:00.0: bridge window [io 0x0000-0xffff]
[ 0.036345] pci 0000:00:00.0: bridge window [mem
0xa0000000-0xbfffffff]
[ 0.036357] pci 0001:02:00.0: BAR 9: can't assign mem pref (size
0x100000)
[ 0.036369] pci 0001:03:00.0: BAR 6: assigned [mem
0x80020000-0x8002ffff pref]
[ 0.036378] pci 0001:02:00.0: PCI bridge to [bus 03]
[ 0.036388] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
[ 0.036397] pci 0001:02:00.0: bridge window [mem
0x80000000-0x9fffffff]
[ 0.036403] Some PCI device resources are unassigned, try booting with
pci=realloc
[ 0.036423] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.036433] pci_bus 0000:00: resource 5 [mem 0xa0000000-0xbfffffff]
[ 0.036443] pci_bus 0000:01: resource 0 [io 0x0000-0xffff]
[ 0.036452] pci_bus 0000:01: resource 1 [mem 0xa0000000-0xbfffffff]
[ 0.036462] pci_bus 0001:02: resource 4 [io 0x20000-0x2ffff]
[ 0.036471] pci_bus 0001:02: resource 5 [mem 0x80000000-0x9fffffff]
[ 0.036481] pci_bus 0001:03: resource 0 [io 0x20000-0x2ffff]
[ 0.036491] pci_bus 0001:03: resource 1 [mem 0x80000000-0x9fffffff]
[ 0.036498] Registering qe_ic with sysfs...
[ 0.039230] bio: create slab <bio-0> at 0
[ 0.040471] Switching to clocksource timebase
[ 0.041834] NET: Registered protocol family 2
[ 0.042154] TCP established hash table entries: 1024 (order: 1, 8192
bytes)
[ 0.042183] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042199] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.042249] TCP: reno registered
[ 0.042259] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.042276] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.042417] NET: Registered protocol family 1
[ 0.042463] PCI: CLS 32 bytes, default 32
[ 0.050953] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.050966] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.051535] msgmni has been set to 246
[ 0.051642] io scheduler noop registered
[ 0.051650] io scheduler deadline registered (default)
[ 0.102060] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.104636] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a
16550A
[ 0.603986] console [ttyS0] enabled
[ 0.608169] ffe04500.serial: ttyS0 at MMIO 0xffe04500 (irq = 42) is a
16550
[ 0.615524] Generic RTC Driver v1.07
[ 0.620362] fsl_espi ffe07000.spi: master is unqueued, this is
deprecated
[ 0.627462] m25p80 spi0.0: s25fl129p1 (16384 Kbytes)
[ 0.632563] 7 ofpart partitions found on MTD device spi0.0
[ 0.638052] Creating 7 MTD partitions on "spi0.0":
[ 0.642845] 0x000000000000-0x000000050000 : "u-boot"
[ 0.648478] 0x000000050000-0x000000060000 : "dtb"
[ 0.653800] 0x000000060000-0x000000300000 : "kernel"
[ 0.659379] 0x000000300000-0x000000fe0000 : "rootfs"
[ 0.664946] mtd: device 3 (rootfs) set to be root filesystem
[ 0.670694] mtd: partition "rootfs_data" created automatically,
ofs=0x4d0000, len=0xb10000
[ 0.678965] 0x0000004d0000-0x000000fe0000 : "rootfs_data"
[ 0.684991] 0x000000fe0000-0x000000ff0000 : "config"
[ 0.690552] 0x000000ff0000-0x000001000000 : "caldata"
[ 0.696206] 0x000000060000-0x000000fe0000 : "firmware"
[ 0.701941] fsl_espi ffe07000.spi: at 0xc901e000 (irq = 59)
[ 0.708402] libphy: Freescale PowerQUICC MII Bus: probed
[ 0.736661] switch0: Atheros AR8327 rev. 2 switch registered on
mdio@ffe24000
[ 1.924680] fsl-gianfar ethernet.1 eth0: mac: 00:04:9f:ef:01:01
[ 1.930614] fsl-gianfar ethernet.1 eth0: Running with NAPI enabled
[ 1.936796] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[0]: 256
[ 1.943323] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[1]: 256
[ 1.949850] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[2]: 256
[ 1.956377] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[3]: 256
[ 1.962905] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[4]: 256
[ 1.969432] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[5]: 256
[ 1.975960] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[6]: 256
[ 1.982487] fsl-gianfar ethernet.1 eth0: RX BD ring size for Q[7]: 256
[ 1.989014] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[0]: 256
[ 1.995541] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[1]: 256
[ 2.002071] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[2]: 256
[ 2.008597] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[3]: 256
[ 2.015124] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[4]: 256
[ 2.021652] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[5]: 256
[ 2.028179] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[6]: 256
[ 2.034706] fsl-gianfar ethernet.1 eth0: TX BD ring size for Q[7]: 256
[ 2.041404] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
[ 2.047705] TCP: cubic registered
[ 2.051037] NET: Registered protocol family 17
[ 2.055542] Bridge firewalling registered
[ 2.059563] 8021q: 802.1Q VLAN Support v1.8
[ 2.068733] VFS: Mounted root (squashfs filesystem) readonly on device
31:3.
[ 2.076182] Freeing unused kernel memory: 132K (c02ee000 - c030f000)
[ 3.548025] usbcore: registered new interface driver usbfs
[ 3.553642] usbcore: registered new interface driver hub
[ 3.559091] usbcore: registered new device driver usb
[ 3.566350] Button Hotplug driver version 0.4.1
[ 3.573218] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.579835] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 3.586469] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus
number 1
[ 3.603548] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
[ 3.620499] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 3.626512] hub 1-0:1.0: USB hub found
[ 3.630289] hub 1-0:1.0: 1 port detected
[ 3.634922] ehci-platform: EHCI generic platform driver
[ 3.956516] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 4.094845] hub 1-1:1.0: USB hub found
[ 4.099005] hub 1-1:1.0: 4 ports detected
[ 5.862898] libphy: mdio@ffe24000:00 - Link is Up - 1000/Full
[ 7.094320] jffs2: notice: (869) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 7 of
xref (0 dead, 2 orphan) found.
[ 10.713117] NET: Registered protocol family 10
[ 10.756745] tun: Universal TUN/TAP device driver, 1.6
[ 10.761811] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 10.787768] nf_conntrack version 0.5.0 (1977 buckets, 7908 max)
[ 10.808721] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.841271] booke_wdt: powerpc book-e watchdog driver loaded
[ 10.855812] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 10.863760] Backport generated by backports.git
backports-20140320-37-g5c33da0
[ 10.883131] input: buttons.8 as /devices/buttons.8/input/input0
[ 10.895621] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.985279] xt_time: kernel timezone is -0000
[ 11.018776] cfg80211: Calling CRDA to update world regulatory domain
[ 11.036561] cfg80211: World regulatory domain updated:
[ 11.041714] cfg80211: DFS Master region: unset
[ 11.046067] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.055810] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 11.063812] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 11.071816] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 11.079831] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 11.087835] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 11.095837] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 11.149704] PPP generic driver version 2.4.2
[ 11.164639] NET: Registered protocol family 24
[ 11.223726] ath: EEPROM regdomain: 0x0
[ 11.223739] ath: EEPROM indicates default country code should be used
[ 11.223743] ath: doing EEPROM country->regdmn map search
[ 11.223754] ath: country maps to regdmn code: 0x3a
[ 11.223760] ath: Country alpha2 being used: US
[ 11.223765] ath: Regpair used: 0x3a
[ 11.232388] ieee80211 phy0: Selected rate control algorithm
'minstrel_ht'
[ 11.242469] cfg80211: Calling CRDA for country: US
[ 11.250041] cfg80211: Regulatory domain changed to country: US
[ 11.255905] cfg80211: DFS Master region: FCC
[ 11.260086] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.269828] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
3000 mBm), (N/A)
[ 11.277831] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A,
1700 mBm), (N/A)
[ 11.285847] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A,
2300 mBm), (0 s)
[ 11.293851] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
3000 mBm), (N/A)
[ 11.301853] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
[ 11.316254] ieee80211 phy0: Atheros AR9300 Rev:4 mem=0xc9740000, irq=17
[ 11.330988] ath: EEPROM regdomain: 0x0
[ 11.331000] ath: EEPROM indicates default country code should be used
[ 11.331005] ath: doing EEPROM country->regdmn map search
[ 11.331016] ath: country maps to regdmn code: 0x3a
[ 11.331022] ath: Country alpha2 being used: US
[ 11.331027] ath: Regpair used: 0x3a
[ 11.344439] ieee80211 phy1: Selected rate control algorithm
'minstrel_ht'
[ 11.362238] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xc97c0000, irq=18
[ 14.684102] device eth0.1 entered promiscuous mode
[ 14.688981] device eth0 entered promiscuous mode
[ 14.698530] br-lan: port 1(eth0.1) entered forwarding state
[ 14.704145] br-lan: port 1(eth0.1) entered forwarding state
[ 15.309518] cfg80211: Calling CRDA for country: IT
[ 15.324223] cfg80211: Regulatory domain changed to country: IT
[ 15.330105] cfg80211: DFS Master region: ETSI
[ 15.334371] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 15.344117] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 15.352120] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 15.360124] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A,
2000 mBm), (0 s)
[ 15.368127] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A,
2700 mBm), (0 s)
[ 15.376131] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
[ 16.679183] libphy: mdio@ffe24000:00 - Link is Up - 1000/Full
[ 16.704974] br-lan: port 1(eth0.1) entered forwarding state
[ 17.509757] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 17.536839] device wlan1 entered promiscuous mode
[ 17.655448] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 17.699902] device wlan0 entered promiscuous mode
[ 17.704722] br-lan: port 3(wlan0) entered forwarding state
[ 17.710268] br-lan: port 3(wlan0) entered forwarding state
[ 18.103684] br-lan: port 2(wlan1) entered forwarding state
[ 18.109225] br-lan: port 2(wlan1) entered forwarding state
[ 18.114771] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 18.378063] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 19.712499] br-lan: port 3(wlan0) entered forwarding state
[ 20.112498] br-lan: port 2(wlan1) entered forwarding state
[ 72.272364] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 72.313114] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 72.352838] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 72.392459] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 72.432937] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 72.472624] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 72.519279] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 72.558957] ath: phy1: Failed to stop TX DMA, queues=0x004!
[ 72.598995] ath: phy1: Failed to stop TX DMA, queues=0x004!
[and more and more atheros errors]
}}}
Others info:
{{{
root@Router:~# iw wlan0 info
Interface wlan0
ifindex 9
wdev 0x2
addr
ssid CC.net-5.2
type AP
wiphy 0
channel 36 (5180 MHz), width: 40 MHz, center1: 5190 MHz
root@Router:~# iw wlan1 info
Interface wlan1
ifindex 10
wdev 0x100000002
addr
ssid CC.net-2.4
type AP
wiphy 1
channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz
root@Router:~# iwinfo
wlan0 ESSID: "CC.net-5.2"
Access Point:
Mode: Master Channel: 36 (5.180 GHz)
Tx-Power: 17 dBm Link Quality: 46/70
Signal: -64 dBm Noise: -93 dBm
Bit Rate: 72.2 MBit/s
Encryption: WPA2 PSK (CCMP)
Type: nl80211 HW Mode(s): 802.11an
Hardware: 168C:0033 168C:A120 [Atheros AR9580]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy0
wlan1 ESSID: "CC.net-2.4"
Access Point:
Mode: Master Channel: 11 (2.462 GHz)
Tx-Power: 20 dBm Link Quality: 41/70
Signal: -69 dBm Noise: -95 dBm
Bit Rate: 72.2 MBit/s
Encryption: WPA2 PSK (CCMP)
Type: nl80211 HW Mode(s): 802.11bgn
Hardware: 168C:0030 0000:0000 [RaLink Rt3352]
TX power offset: none
Frequency offset: none
Supports VAPs: yes PHY name: phy1
root@Router:~#
}}}
I'm available for any test.
Fabio
--
Ticket URL: <https://dev.openwrt.org/ticket/16752>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
