#16909: logread show "logread Failed to find log object: Not found"
-----------------------+---------------------------------------
Reporter: xinglp | Owner: developers
Type: defect | Status: new
Priority: normal | Milestone: Attitude Adjustment 12.09
Component: packages | Version: Trunk
Resolution: | Keywords:
-----------------------+---------------------------------------
Comment (by xinglp):
Replying to [comment:2 blogic]:
> can you make a real bug report ? bootlog, hw used etc etc
TEW-632BRP
{{{
U-Boot 1.1.4 (Mar 23 2009 - 15:07:56)
AP81 (ar7100) U-boot
DRAM: AP81 initdram
sri:ddr_init
32 MB
Top of RAM usable for U-Boot at: 82000000
Reserving 177k for U-Boot at: 81fd0000
Reserving 192k for malloc() at: 81fa0000
Reserving 44 Bytes for Board Info at: 81f9ffd4
Reserving 36 Bytes for Global Data at: 81f9ffb0
Reserving 128k for boot params() at: 81f7ffb0
Stack Pointer at: 81f7ff98
Now running in RAM - U-Boot at: 81fd0000
ar7100 flash_init
id read 0x10000107
flash size 400000, sector count = 64
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: eth_initialize CONFIG_NET_MULTI
ag7100_enet_initialize
eth0: 00:14:d1:65:b3:13
ethernet found.
eth0
## Booting image at bf030000 ...
checksum:1549c987
Image Name: MIPS OpenWrt Linux-3.10.44
Created: 2014-06-28 3:10:07 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 869133 Bytes = 848.8 kB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum ... OK
LZMA Umcompressing Kernel Image ... Image loaded from
80060000-802e7ed4
OK
Boot image os 5=IH_OS_LINUX
## do_bootm_linux start....
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 33554432
##Starting kernel ...
Linux version 3.10.44 (xxxx@xxxxxx) (gcc version 4.8.3 (OpenWrt/Linaro GCC
4.8-2014.04 r41302) ) #6 Sat Jun 28 11:09:53 CST 2014
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
SoC: Atheros AR9130 rev 2
Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:100.000MHz, Ref:5.000MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone ranges:
Normal [mem 0x00000000-0x01ffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x01ffffff]
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: board=TEW-632BRP console=ttyS0,115200
mtdparts=spi0.0:128k(u-boot)ro,64k(config)ro,3840k(firmware),64k(art)ro
rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29236k/32768k available (2033k kernel code, 3532k reserved, 340k
data, 248k init, 0k highmem)
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:51
Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TRENDnet TEW-632BRP
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c)
2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
ath79-spi ath79-spi: master is unqueued, this is deprecated
m25p80 spi0.0: found s25sl032a, expected m25p80
m25p80 spi0.0: s25sl032a (4096 Kbytes)
4 cmdlinepart partitions found on MTD device spi0.0
Creating 4 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000030000 : "config"
0x000000030000-0x0000003f0000 : "firmware"
2 uimage-fw partitions found on MTD device firmware
0x000000030000-0x00000010434d : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary
or be smaller than an erase block -- forcing read-only
0x00000010434d-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary
or be smaller than an erase block -- forcing read-only
mtd: device 4 (rootfs) set to be root filesystem
1 squashfs-split partitions found on MTD device rootfs
0x0000002a0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "art"
switch0: Atheros AR8216 rev. 1 switch registered on ag71xx-mdio.0
libphy: ag71xx_mdio: probed
ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd042,
driver=Atheros AR8216/AR8236/AR8316]
eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RMII
ag71xx ag71xx.1: connected to PHY at ag71xx-mdio.0:04 [uid=004dd042,
driver=Atheros AR8216/AR8236/AR8316]
eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RMII
TCP: cubic registered
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 248K (802b2000 - 802f0000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug
level
eth0: link up (100Mbps/Full duplex)
jffs2 is ready
jffs2 is ready
jffs2: notice: (285) jffs2_build_xattr_subsystem: complete building xattr
subsystem, 6 of xdatum (1 unchecked, 5 orphan) and 26 of xref (0 dead, 13
orphan) found.
switching to overlay
eth0: link down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
nf_conntrack version 0.5.0 (460 buckets, 1840 max)
ip6_tables: (C) 2000-2006 Netfilter Core Team
Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
Backport generated by backports.git backports-20140320-37-g5c33da0
ip_tables: (C) 2000-2006 Netfilter Core Team
xt_time: kernel timezone is -0000
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm),
(N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm),
(N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm),
(N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm),
(N/A)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm),
(N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm),
(N/A)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2
mem=0xb80c0000, irq=2
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
cfg80211: DFS Master region: FCC
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm),
(N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm),
(N/A)
cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0
s)
cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm),
(N/A)
cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm),
(N/A)
procd: - init complete -
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
device eth0 entered promiscuous mode
IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
eth0: link up (100Mbps/Full duplex)
br-lan: port 1(eth0) entered forwarding state
br-lan: port 1(eth0) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entered forwarding state
br-lan: port 2(wlan0) entered forwarding state
br-lan: port 2(wlan0) entered disabled state
br-lan: port 2(wlan0) entered forwarding state
br-lan: port 2(wlan0) entered forwarding state
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
br-lan: port 1(eth0) entered forwarding state
eth1: link up (100Mbps/Full duplex)
IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
br-lan: port 2(wlan0) entered forwarding state
BusyBox v1.22.1 (2014-06-27 22:51:55 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r41363)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@xxxx:/#
}}}
--
Ticket URL: <https://dev.openwrt.org/ticket/16909#comment:3>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
