#18134: ADB PD.G A4001N USB Problem
---------------------------------+-----------------------------------
Reporter: valerio.fanciullo@… | Owner: developers
Type: defect | Status: new
Priority: normal | Milestone: Barrier Breaker 14.07
Component: packages | Version: Barrier Breaker 14.07
Keywords: usb,adb,A4001N |
---------------------------------+-----------------------------------
The USB port on this router doesn't work with Open WRT, i've tried with
Barrier Breaker and Attitude Adjustment but nothing, the usb port is dead
the system doesn't recognize it, but with other custom or original
firmware it work fine.
This is my dmesg, the usb packages start but when i insert an USB Hub or a
Pen Drive the system doesn't spot it:
{{{
[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3
(OpenWrt/Linaro GCC 4.8-2014.04 r42625) ) #3 Wed Oct 1 15:07:11 CEST 2014
[ 0.000000] Detected Broadcom 0x6328 CPU revision b0
[ 0.000000] CPU frequency is 320 MHz
[ 0.000000] 32MB of RAM installed
[ 0.000000] registering 32 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
[ 0.000000] board_bcm963xx: CFE version: 1.0.37-106.17-1
[ 0.000000] No bcm_tag found!
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
[ 0.000000] board: board name: 96328avng
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 80318c60, node_mem_map
81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16
bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases,
linesize 16 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 8128
[ 0.000000] Kernel command line: root=/dev/mtdblock2
rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 28656k/32768k available (2485k kernel code, 4112k
reserved, 725k data, 308k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.036000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.288000] registering PCI controller with io_map_base unset
[ 0.304000] bio: create slab <bio-0> at 0
[ 0.312000] PCI host bridge to bus 0000:00
[ 0.316000] pci_bus 0000:00: root bus resource [mem
0x10f00000-0x10ffffff]
[ 0.320000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags
0x0]
[ 0.324000] pci_bus 0000:00: No busn resource found for root bus, will
use [bus 00-ff]
[ 0.328000] pci 0000:00:00.0: [14e4:6328] type 01 class 0x060400
[ 0.328000] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 0.328000] pci 0000:00:00.0: bridge configuration invalid ([bus
00-00]), reconfiguring
[ 0.332000] pci 0000:01:00.0: [14e4:a8d8] type 00 class 0x028000
[ 0.332000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00003fff 64bit]
[ 0.332000] pci 0000:01:00.0: supports D1 D2
[ 0.332000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.332000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.332000] pci 0000:00:00.0: BAR 8: assigned [mem
0x10f00000-0x10ffffff]
[ 0.336000] pci 0000:01:00.0: BAR 0: assigned [mem
0x10f00000-0x10f03fff 64bit]
[ 0.340000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.344000] pci 0000:00:00.0: bridge window [mem
0x10f00000-0x10ffffff]
[ 0.348000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 0.352000] Switching to clocksource MIPS
[ 0.360000] NET: Registered protocol family 2
[ 0.368000] TCP established hash table entries: 512 (order: 0, 4096
bytes)
[ 0.376000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.380000] TCP: Hash tables configured (established 512 bind 512)
[ 0.388000] TCP: reno registered
[ 0.392000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.396000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.404000] NET: Registered protocol family 1
[ 0.408000] PCI: CLS 0 bytes, default 16
[ 0.412000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.432000] msgmni has been set to 55
[ 0.436000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.448000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a
bcm63xx_uart
[ 0.456000] console [ttyS0] enabled, bootconsole disabled
[ 0.472000] m25p80 spi1.0: found mx25l12805d, expected m25p80
[ 0.480000] m25p80 spi1.0: mx25l12805d (16384 Kbytes)
[ 0.484000] bcm63xxpart: CFE boot tag found with version 6 and board
type 96328dg2x2
[ 0.492000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[ 0.500000] bcm63xxpart: Partition 1 is kernel offset 10100 and length
11ff00
[ 0.508000] bcm63xxpart: Partition 2 is rootfs offset 130000 and length
ec0000
[ 0.516000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length
10000
[ 0.520000] bcm63xxpart: Partition 4 is linux offset 10000 and length
fe0000
[ 0.528000] bcm63xxpart: Spare partition is offset 350004 and length
c9fffc
[ 0.536000] 5 bcm63xxpart partitions found on MTD device spi1.0
[ 0.544000] Creating 5 MTD partitions on "spi1.0":
[ 0.548000] 0x000000000000-0x000000010000 : "CFE"
[ 0.556000] 0x000000010100-0x000000130000 : "kernel"
[ 0.560000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.576000] 0x000000130000-0x000000ff0000 : "rootfs"
[ 0.584000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.588000] mtd: partition "rootfs_data" created automatically,
ofs=0x350000, len=0xca0000
[ 0.600000] 0x000000350000-0x000000ff0000 : "rootfs_data"
[ 0.608000] 0x000000ff0000-0x000001000000 : "nvram"
[ 0.616000] 0x000000010000-0x000000ff0000 : "linux"
[ 0.664000] b53_common: found switch: BCM63xx, rev 0
[ 0.672000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.684000] TCP: cubic registered
[ 0.684000] NET: Registered protocol family 17
[ 0.692000] Bridge firewalling registered
[ 0.696000] 8021q: 802.1Q VLAN Support v1.8
[ 0.712000] VFS: Mounted root (squashfs filesystem) readonly on device
31:2.
[ 0.724000] Freeing unused kernel memory: 308K (80333000 - 80380000)
[ 4.144000] Button Hotplug driver version 0.4.1
[ 4.980000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4,
100Mbps, full-duplex
[ 8.696000] jffs2: notice: (209) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 21 of xdatum (1 unchecked, 20 orphan) and 31 of
xref (0 dead, 22 orphan) found.
[ 9.876000] usbcore: registered new interface driver usbfs
[ 9.880000] usbcore: registered new interface driver hub
[ 9.888000] usbcore: registered new device driver usb
[ 10.136000] SCSI subsystem initialized
[ 10.156000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.164000] ehci-platform: EHCI generic platform driver
[ 10.180000] uhci_hcd: USB Universal Host Controller Interface driver
[ 10.196000] usbcore: registered new interface driver usb-storage
[ 13.540000] NET: Registered protocol family 10
[ 13.560000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 13.568000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package
0x0A
[ 13.572000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id
0x800, rev 0x22, class 0x0)
[ 13.584000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id
0x812, rev 0x17, class 0x0)
[ 13.592000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev
0x0F, class 0x0)
[ 13.680000] bcma: bus0: Invalid SPROM read from the PCIe card, trying
to use fallback SPROM
[ 13.692000] bcma: bus0: Using fallback SPROM failed (err -2)
[ 13.696000] bcma: bus0: No SPROM available
[ 13.712000] bcma: bus0: Bus registered
[ 13.732000] nf_conntrack version 0.5.0 (452 buckets, 1808 max)
[ 13.752000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 13.780000] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 13.788000] Backport generated by backports.git
backports-20140320-37-g5c33da0
[ 13.800000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.884000] xt_time: kernel timezone is -0000
[ 13.944000] cfg80211: Calling CRDA to update world regulatory domain
[ 13.956000] cfg80211: World regulatory domain updated:
[ 13.960000] cfg80211: DFS Master region: unset
[ 13.964000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 13.972000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 13.984000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 13.992000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 14.000000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A,
2000 mBm), (N/A)
[ 14.008000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 14.016000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 14.024000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 14.032000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 14.172000] PPP generic driver version 2.4.2
[ 14.184000] NET: Registered protocol family 24
[ 14.236000] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
[ 14.244000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[ 14.248000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 11,
Version 0
[ 14.264000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 14.272000] ieee80211 phy0: Selected rate control algorithm
'minstrel_ht'
[ 26.300000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4,
100Mbps, full-duplex
[ 26.316000] device eth0 entered promiscuous mode
[ 26.324000] br-lan: port 1(eth0) entered forwarding state
[ 26.328000] br-lan: port 1(eth0) entered forwarding state
[ 28.332000] br-lan: port 1(eth0) entered forwarding state
}}}
--
Ticket URL: <https://dev.openwrt.org/ticket/18134>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
