#18647: board_bcm963xx: unknown bcm963xx board: 96328AVNG_N31
----------------------+-----------------------------------
Reporter: AntonCH | Owner: developers
Type: task | Status: new
Priority: normal | Milestone: Barrier Breaker 14.07
Component: packages | Version: Trunk
Keywords: |
----------------------+-----------------------------------
Please add support for board id 96328AVNG_N31
Log on original firmware
{{{
CFE version 1.0.37-106.24 for BCM96328 (32bit,SP,BE)
Build Date: Втр Авг 2 10:56:54 UTC 2011 (builder@cel366)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name ID_W25X32, id 0xef16 size 4096KB
Total Flash size: 4096K with 1024 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-6) : 96328AVNG_N31
Number of MAC Addresses (1-32) : 11
Base MAC Address : 1c:7e:e5:ee:ca:cd
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
Voice Board Configuration (0-11) :
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x800144a0
Decompression OK!
Entry at 0x800144a0
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x800144a0
Linux version 2.6.30 (builder@rd) (gcc version 4.4.2 (Buildroot
2010.02-git) ) #
1 Mon Feb 18
17:36:58 MSK 2013
HS Serial flash device: name ID_W25X32, id 0xef16 size 4096KB
96328AVNG_N31 prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 802ad8d0, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60800k/64512k available (2229k kernel code, 3692k reserved, 455k
data, 1
16k init, 0k
highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 820 bytes
NET: Registered protocol family 16
Total Flash size: 4096K with 1024 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v3.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
msgmni has been set to 118
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check
vendor B
IOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8009 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Feb 18 2013
17:36:43
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom Logger v0.1 Feb 18 2013 17:36:39
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 116k freed
init started: BusyBox v1.00 (2013.02.18-13:37+0000) multi-call binary
mount: Mounting usbfs on /proc/bus/usb failed: No such file or directory
making /var/log..
making /var/run..
making /var/state/dhcp..
making /var/ppp..
making /var/ppp/peers..
making /var/udhcpd..
making /var/zebra..
making /var/siproxd..
making /var/tmp..
mount: Mounting usbfs on /proc/bus/usb failed: No such file or directory
gpio: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
start /etc/init.d/S*...
/etc/init.d/S*: not found
96328AVNG_N31
BusyBox v1.00 (2013.02.18-13:37+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
Initialized fcache state
Broadcom Packet Flow Cache Char Driver v2.2 Sep 24 2010 18:42:19
Registered<242
>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Sep 24 2010 18:42:19
Broadcom BCM6328B0 Ethernet Network Device v0.1 Feb 18 2013 17:36:41
ETH Init: 180 tx BDs at 0xa3861000
ETH Init: 400 rx BDs at 0xa39dd000
ETH Init: 400 rx BDs at 0xa39dc000
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: 1C:7E:E5:EE:CA:CD
eth1: MAC Address: 1C:7E:E5:EE:CA:CD
eth2: MAC Address: 1C:7E:E5:EE:CA:CD
eth3: MAC Address: 1C:7E:E5:EE:CA:CD
eth4: MAC Address: 1C:7E:E5:EE:CA:CD
eth1 Link UP 100 mbps full duplex
eth3 Link UP 100 mbps full duplex
message received before monitor task is initialized
kerSysSendtoMonitorTask
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom strapped
wl:(srom strapped) probe/present=0
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43225_map.bin
wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.11.cpe4.06L03.8
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
p8021ag: p8021ag_init entry
Broadcom 802.1Q VLAN Interface, v0.1
===== Release Version 4.06L.03 (build timestamp 130218_1737) =====
device eth0 entered promiscuous mode
ip_tables: (C) 2000-2006 Netfilter Core Team
device eth1 entered promiscuous mode
br0: port 2(eth1) entering forwarding state
modprobe: could not parse modules.dep
modprobe: could not parse modules.dep
dhcpd uses obsolete (PF_INET,SOCK_PACKET)
device eth2 entered promiscuous mode
device eth4 entered promiscuous mode
modprobe: could not parse modules.dep
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
BcmAdsl_Initialize=0x80169E60, g_pFnNotifyCallback=0x802A6BB4
WLmngr Daemon is running
optarg=0 shmId=0
pSdramPHY=0xA3FFFFF8, 0x0 0x0
wlevt_init@107: opened loopback socket 4
wlevt is ready for new msg...
AdslCoreSharedMemInit: shareMemAvailable=491424
AdslCoreHwReset: AdslOemDataAddr = 0xA3F69564
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
XTM Init: 400 rx BDs at 0xa2ddc000
XTM Init: 100 rx BDs at 0xa2dc2000
monitor task is initialized pid= 251
(ssk) EthernetWan eth3 link up
Lenght of avalible memory for title 188 bytes
environ TMOUT=0
environ LD_LIBRARY_PATH=/lib/public:/lib/private:/lib/gpl:/lib
environ USER=root
environ SHELL=/bin/sh
environ
PATH=/home/bin:/home/scripts:/opt/bin:/opt/scripts:/bin:/sbin:/usr/bin
environ TERM=vt102
environ HOME=/
resident starting...
recovered previous ppp session info ppp1(0030881c6c76/2125)
count_detected_rpc = 93
1. rpc - 0, type - 2, flags - 0x0000, glocks - 0x0000, version - 0,
sona
me - "somovd",
fname - "InternalAction"
2. rpc - 88, type - 3, flags - 0x0002, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/libcommon.so", fname - "SetProxyAddr"
3. rpc - 19, type - 3, flags - 0x0002, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/libcommon.so", fname - "GetConfigStatus"
4. rpc - 6, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/libcommon.so", fname - "Reboot"
5. rpc - 99, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/libcommon.so", fname - "SystemCommand"
6. rpc - 25, type - 3, flags - 0x0001, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/libcommon.so", fname - "DataUpload"
7. rpc - 26, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/libcommon.so", fname - "DataDownload"
8. rpc - 145, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/libcommon.so", fname - "conf_ping"
9. rpc - 163, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/libcommon.so", fname - "salt_conf"
10. rpc - 166, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/libcommon.so", fname - "conf_traceroute"
11. rpc - 33, type - 4, flags - 0x0002, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/libcommon.so", fname - "route_table"
12. rpc - 143, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/libcommon.so", fname - "conf_web_profiles"
13. rpc - 20, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "SaveConfig"
14. rpc - 8, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "SaveAndReboot"
15. rpc - 10, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "ResetAndReboot"
16. rpc - 11, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "RestoreConfig"
17. rpc - 12, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "BackupConfig"
18. rpc - 93, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "BackupConfigForGcc"
19. rpc - 13, type - 3, flags - 0x0001, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "FirmwareUpload"
20. rpc - 14, type - 3, flags - 0x0001, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "FirmwareUpdate"
21. rpc - 37, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "check_reset"
22. rpc - 24, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "button_test"
23. rpc - 23, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "leds_do"
24. rpc - 41, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "check_default"
25. rpc - 39, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "leds_do_red"
26. rpc - 91, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "set_fon_hwdata"
27. rpc - 92, type - 3, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "set_fon_key_data"
28. rpc - 24, type - 4, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "dsl_status"
29. rpc - 25, type - 4, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "dsl_status"
30. rpc - 28, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wan_status"
31. rpc - 34, type - 4, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "dhcp_leases"
32. rpc - 2, type - 4, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "sdhcp_conf"
33. rpc - 5, type - 4, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "adsl_conf"
34. rpc - 6, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "ddns_conf"
35. rpc - 7, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "dns_conf"
36. rpc - 9, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "rules_conf"
37. rpc - 88, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "rules_conf"
38. rpc - 22, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "rules_conf"
39. rpc - 10, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "vservers_conf"
40. rpc - 15, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "vservers_conf"
41. rpc - 74, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "brfiltres_conf"
42. rpc - 19, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "brfiltres_conf"
43. rpc - 20, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "ifgroups_conf_new"
44. rpc - 14, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "ifgroups_conf_new"
45. rpc - 16, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "httpaccess_conf"
46. rpc - 17, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "routing_conf"
47. rpc - 125, type - 4, flags - 0x0000, glocks - 0x0000, version - 1,
sona
me -
"/lib/private/librcm.so", fname - "routing_conf_cli"
48. rpc - 23, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "dmz_conf"
49. rpc - 35, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
50. rpc - 36, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
51. rpc - 37, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
52. rpc - 38, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
53. rpc - 39, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
54. rpc - 170, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
55. rpc - 40, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
56. rpc - 41, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
57. rpc - 42, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
58. rpc - 44, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
59. rpc - 64, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
60. rpc - 105, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
sona
me -
"/lib/private/librcm.so", fname - "wifi_conf"
61. rpc - 106, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
soname - "/lib/private/librcm.so", fname - "wifi_conf"
62. rpc - 107, type - 4, flags - 0x0000, glocks - 0x0000, version - 3,
soname - "/lib/private/librcm.so", fname - "wifi_conf"
63. rpc - 26, type - 4, flags - 0x0000, glocks - 0x0000, version - 1,
soname - "/lib/private/librcm.so", fname - "simple_conf"
64. rpc - 27, type - 4, flags - 0x0000, glocks - 0x0000, version - 1,
soname - "/lib/private/librcm.so", fname - "simple_conf"
65. rpc - 69, type - 4, flags - 0x0000, glocks - 0x0000, version - 1,
soname - "/lib/private/librcm.so", fname - "pass_conf"
66. rpc - 63, type - 4, flags - 0x0000, glocks - 0x000it,SP,BE)
Build Date: Втр Авг 2 10:56:54 UTC 2011 (builder@cel366)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name ID_W25X32, id 0xef16 size 4096KB
Total Flash size: 4096K with 1024 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-6) : 96328AVNG_N31
Number of MAC Addresses (1-32) : 11
Base MAC Address : 1c:7e:e5:ee:ca:cd
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
Voice Board Configuration (0-11) :
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x800144a0
Decompression OK!
Entry at 0x800144a0
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x800144a0
Linux version 2.6.30 (builder@rd) (gcc version 4.4.2 (Buildroot
2010.02-git) ) #
1 Mon Feb 18
17:36:58 MSK 2013
HS Serial flash device: name ID_W25X32, id 0xef16 size 4096KB
96328AVNG_N31 prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 802ad8d0, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60800k/64512k available (2229k kernel code, 3692k reserved, 455k
data, 1
16k init, 0k
highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 820 bytes
NET: Registered protocol family 16
Total Flash size: 4096K with 1024 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v3.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
msgmni has been set to 118
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check
vendor B
IOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8009 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Feb 18 2013
17:36:43
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom Logger v0.1 Feb 18 2013 17:36:39
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered%
}}}
--
Ticket URL: <https://dev.openwrt.org/ticket/18647>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
