#20975: tp-link w8970 don't boot
-------------------------+------------------------
Reporter: peppino | Owner: developers
Type: defect | Status: new
Priority: normal | Milestone:
Component: base system | Version: Trunk
Keywords: |
-------------------------+------------------------
U-Boot 2010.06-LANTIQ-v-2.0.40-svn4806 (Jun 12 2014 - 10:34:17)
CLOCK CPU 500M RAM 250M
DRAM: 64 MiB
Using default environment
In: serial
Out: serial
Err: serial
Net: Internal phy(GE) firmware version: 0x8434
vr9 Switch8192 KiB W25Q64 at 0:3 is now current device
Type "run flash_nfs" to mount root filesystem over NFS
Hit any key to stop autoboot: 0
8192 KiB W25Q64 at 0:3 is now current device
8192 KiB W25Q64 at 0:3 is now current device
Uncompressing ...
Starting kernel ...
[ 0.000000] Linux version 4.1.11 (salvatore@ubuntu) (gcc version 5.2.0
(OpenWrt GCC 5.2.0 r47641) ) #1 Wed Nov 25 10:36:15 PST 2015
[ 0.000000] SoC: VR9 rev 1.2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[ 0.000000] MIPS: machine is TDW8970 - TP-LINK TD-W8970
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem
0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200
init=/etc/preinit panic=1
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.000000] Writing ErrCtl register=0004415c
[ 0.000000] Readback ErrCtl register=0004415c
[ 0.000000] Memory: 59556K/65536K available (3783K kernel code, 147K
rwdata, 988K rodata, 180K init, 207K bss, 5980K reserved, 0K cma-reserved)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 500MHz
[ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 7645041786 ns
[ 0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every
8589934590ns
[ 0.008197] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.042320] pid_max: default: 32768 minimum: 301
[ 0.047315] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.053797] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.066918] clocksource jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.076635] pinctrl core: initialized pinctrl subsystem
[ 0.082463] NET: Registered protocol family 16
[ 0.091373] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.096914] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7,
channels: 28
[ 0.207379] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.325264] ath9k,eeprom ath9k_eep: failed to load eeprom address
[ 0.353412] usbcore: registered new interface driver usbfs
[ 0.358909] usbcore: registered new interface driver hub
[ 0.364276] usbcore: registered new device driver usb
[ 0.369604] PCI host bridge to bus 0000:00
[ 0.373591] pci_bus 0000:00: root bus resource [mem
0x1c000000-0x1cffffff]
[ 0.380508] pci_bus 0000:00: root bus resource [io
0x1d800000-0x1d8fffff]
[ 0.387450] pci_bus 0000:00: root bus resource [??? 0x00000000 flags
0x0]
[ 0.394306] pci_bus 0000:00: No busn resource found for root bus, will
use [bus 00-ff]
[ 0.402356] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to
pci-pci bridge
[ 0.421225] pci 0000:00:00.0: BAR 8: assigned [mem
0x1c000000-0x1c0fffff]
[ 0.427903] pci 0000:00:00.0: BAR 9: assigned [mem
0x1c100000-0x1c1fffff pref]
[ 0.435171] pci 0000:01:00.0: BAR 0: assigned [mem
0x1c000000-0x1c01ffff 64bit]
[ 0.442570] pci 0000:01:00.0: BAR 6: assigned [mem
0x1c100000-0x1c10ffff pref]
[ 0.449832] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.454868] pci 0000:00:00.0: bridge window [mem
0x1c000000-0x1c0fffff]
[ 0.461724] pci 0000:00:00.0: bridge window [mem
0x1c100000-0x1c1fffff pref]
[ 0.469032] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
[ 0.475690] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
[ 0.482039] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[ 0.488706] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[ 0.496035] Switched to clocksource MIPS
[ 0.501665] NET: Registered protocol family 2
[ 0.507099] TCP established hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.513995] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.520365] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.526934] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.532723] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.539427] NET: Registered protocol family 1
[ 0.544246] gptu: totally 6 16-bit timers/counters
[ 0.549061] gptu: misc_register on minor 63
[ 0.553173] gptu: succeeded to request irq 126
[ 0.557665] gptu: succeeded to request irq 127
[ 0.562179] gptu: succeeded to request irq 128
[ 0.566693] gptu: succeeded to request irq 129
[ 0.571207] gptu: succeeded to request irq 130
[ 0.575720] gptu: succeeded to request irq 131
[ 0.581135] phy-xrx200 gphy-xrx200: requesting
lantiq/vr9_phy11g_a2x.bin
[ 0.588543] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 3A20000
[ 0.594860] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 3A20000
[ 0.702684] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.717810] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.723551] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.735183] io scheduler noop registered
[ 0.739036] io scheduler deadline registered (default)
[ 0.744910] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112,
base_baud = 0) is a lantiq,asc
[ 0.753806] console [ttyLTQ0] enabled
[ 0.753806] console [ttyLTQ0] enabled
[ 0.761136] bootconsole [early0] disabled
[ 0.761136] bootconsole [early0] disabled
[ 0.773723] Lantiq SoC SPI controller rev 8 (TXFS 8, RXFS 8, DMA 1)
[ 0.881058] libphy: lantiq,xrx200-mdio: probed
[ 0.890673] net-xrx200: invalid MAC, using random
[ 0.956768] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00,
irq=-1)
[ 1.024740] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05,
irq=-1)
[ 1.092727] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4]
(phy_addr=0:11, irq=-1)
[ 1.160729] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4]
(phy_addr=0:13, irq=-1)
[ 1.168575] wdt 1f8803f0.watchdog: Init done
[ 1.173478] NET: Registered protocol family 10
[ 1.180006] NET: Registered protocol family 17
[ 1.183155] bridge: automatic filtering via arp/ip/ip6tables has been
deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.195714] Bridge firewalling registered
[ 1.199663] 8021q: 802.1Q VLAN Support v1.8
[ 1.204197] ath9k,eeprom ath9k_eep: failed to load eeprom address
[ 1.214345] UBIFS error (pid: 1): cannot open "ubi0:rootfs", error
-19VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 1.225462] Please append a correct "root=" boot option; here are the
available partitions:
[ 1.233798] Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
[ 1.243234] Rebooting in 1 seconds..
--
Ticket URL: <https://dev.openwrt.org/ticket/20975>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
