#21284: EA3500 (Audi Kirkwood) wifi unstable.
------------------------+---------------------------------------
Reporter: anonymous | Owner: developers
Type: defect | Status: new
Priority: normal | Milestone: Designated Driver (Trunk)
Component: kernel | Version: Trunk
Resolution: | Keywords:
------------------------+---------------------------------------
Comment (by anonymous):
After about 18h testing, wifi still unstable:
[ 356.632570] ieee80211 phy0: Added a new stream for d0:22:be:ce:e5:62 1
[ 356.639200] ieee80211 phy0: Started stream for d0:22:be:ce:e5:62 1
[ 356.646041] ieee80211 phy0: tx rings drained
[ 356.697334] ieee80211 phy0: Created a BA stream for d0:22:be:ce:e5:62 :
tid 1
[ 356.705646] ieee80211 phy0: Deleted BA stream index 0
[ 356.710775] ieee80211 phy0: Remove stream for d0:22:be:ce:e5:62 1
[ 607.800757] ieee80211 phy1: Added a new stream for d0:22:be:ce:e5:62 1
[ 607.807379] ieee80211 phy1: Started stream for d0:22:be:ce:e5:62 1
[ 607.818660] ieee80211 phy1: Created a BA stream for d0:22:be:ce:e5:62 :
tid 1
[ 608.711340] ieee80211 phy1: Added a new stream for d0:22:be:ce:e5:62 0
[ 608.717958] ieee80211 phy1: Started stream for d0:22:be:ce:e5:62 0
[ 608.726972] ieee80211 phy1: Created a BA stream for d0:22:be:ce:e5:62 :
tid 0
[ 627.826948] ieee80211 phy1: tx rings drained
[ 627.831406] ieee80211 phy1: Deleted BA stream index 1
[ 627.836613] ieee80211 phy1: Remove stream for d0:22:be:ce:e5:62 0
[ 627.843221] ieee80211 phy1: Deleted BA stream index 0
[ 627.848302] ieee80211 phy1: Remove stream for d0:22:be:ce:e5:62 1
[34755.804092] ieee80211 phy0: Started stream for 48:5a:3f:3f:99:f9 1
[34755.810409] ieee80211 phy0: Command BASTREAM error 0x1
[34756.820609] ieee80211 phy0: Command BASTREAM error 0x1
[34757.830624] ieee80211 phy0: Command BASTREAM error 0x1
[34758.840640] ieee80211 phy0: Command BASTREAM error 0x1
[34759.850650] ieee80211 phy0: Command BASTREAM error 0x1
[34760.860621] ieee80211 phy0: Stream for tid 1 busy after 5 attempts
[34760.866839] ieee80211 phy0: Remove stream for 48:5a:3f:3f:99:f9 1
[57936.583888] ieee80211 phy0: Deleted BA stream index 0
[57936.588976] ieee80211 phy0: Remove stream for 00:22:fa:c9:ec:be 1
[61768.543338] ieee80211 phy0: Started stream for 00:22:fa:c9:ec:be 0
[61768.555213] ieee80211 phy0: Created a BA stream for 00:22:fa:c9:ec:be :
tid 0
[61797.232342] ieee80211 phy0: Deleted BA stream index 0
[61797.237803] ieee80211 phy0: Remove stream for 00:22:fa:c9:ec:be 0
[61797.850008] ieee80211 phy0: Added a new stream for 00:22:fa:c9:ec:be 0
[61797.856621] ieee80211 phy0: Started stream for 00:22:fa:c9:ec:be 0
[61797.863258] ieee80211 phy0: Command BASTREAM error 0x1
[61798.876026] ieee80211 phy0: Command BASTREAM error 0x1
[61799.886029] ieee80211 phy0: Command BASTREAM error 0x1
[61800.900234] ieee80211 phy0: Created a BA stream for 00:22:fa:c9:ec:be :
tid 0
[61810.370663] ieee80211 phy0: Deleted BA stream index 0
[61810.375753] ieee80211 phy0: Remove stream for 00:22:fa:c9:ec:be 0
[61812.017030] ieee80211 phy0: Added a new stream for 00:22:fa:c9:ec:be 0
[61812.023621] ieee80211 phy0: Started stream for 00:22:fa:c9:ec:be 0
[61812.030377] ieee80211 phy0: Command BASTREAM error 0x1
[61813.036183] ieee80211 phy0: Command BASTREAM error 0x1
[61814.050587] ieee80211 phy0: Created a BA stream for 00:22:fa:c9:ec:be :
tid 0
[61829.742939] ieee80211 phy0: Deleted BA stream index 0
[61829.748057] ieee80211 phy0: Remove stream for 00:22:fa:c9:ec:be 0
[61834.687894] ieee80211 phy0: Added a new stream for 00:22:fa:c9:ec:be 0
[61834.694489] ieee80211 phy0: Started stream for 00:22:fa:c9:ec:be 0
[61834.709227] ieee80211 phy0: Created a BA stream for 00:22:fa:c9:ec:be :
tid 0
[61842.427391] ieee80211 phy0: Deleted BA stream index 0
[61842.432479] ieee80211 phy0: Remove stream for 00:22:fa:c9:ec:be 0
I tested with two device, one laptop (intel 5100agn) & one galaxy note 3.
Here are openwrt bootlog:
U-Boot 1.1.4 (Jan 2 2012 - 19:59:08) Marvell version: 3.5.9
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB20
Soc: 88F6282 A1CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM (DDR2) CAS Latency = 5 tRP = 6 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 64MB
DRAM Total size 64MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:64 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
u_env Offset: 00080000
s_env Offset: 00084000
Streaming disabled
Write allocate disabled
Module 0 is RGMII
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: PCI Express Root Complex Interface
PEX interface detected Link X1
Updating boot_count ... done
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x1600000, size 0x300000
Reading data from 0x18ffe00 -- 100% complete.
3145728 bytes read: OK
## Booting image at 02000000 ...
Image Name: ARM OpenWrt Linux-3.18.23
Created: 2015-11-30 11:15:26 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1867470 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.18.23 (thepeople@trabant) (gcc version
5.2.0 (OpenWrt GCC 5.2.0 r47670) ) #1 Mon Nov 30 12:15:02 CET 2015
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE),
cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Linksys EA3500
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200
mtdparts=nand_mtd:512k(uboot)ro,16k@512k(u_env),16k@528k(s_env),20m@2m(kernel),20m@2m(rootfs)fs,20m@22m(alt_kernel),20m@22m(alt_rootfs)fs,22m@42m(syscfg)
root=/dev/mtdblock6 ro rootfstype=jffs2 serial_number=12C10609206650
uuid=6C95894C93CD9F81CB66BC4AA876D195 hw_version=RGWM-C5_0GA
device_mac=C8:D7:19:17:72:42 factory_date=2012/09/24 wps_pin=21833489
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.000000] Memory: 59524K/65536K available (3802K kernel code, 160K
rwdata, 1016K rodata, 148K init, 198K bss, 6012K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xc4800000 - 0xff000000 ( 936 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc04bcd74 (4820 kB)
[ 0.000000] .init : 0xc04bd000 - 0xc04e2000 ( 148 kB)
[ 0.000000] .data : 0xc04e2000 - 0xc050a0e4 ( 161 kB)
[ 0.000000] .bss : 0xc050a0e4 - 0xc053b908 ( 199 kB)
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000017] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every
21474836475ns
[ 0.000189] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[ 0.040100] pid_max: default: 32768 minimum: 301
[ 0.040272] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040295] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.040868] CPU: Testing write buffer coherency: ok
[ 0.041244] Setting up static identity map for 0x11030 - 0x1106c
[ 0.041593] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[ 0.043880] pinctrl core: initialized pinctrl subsystem
[ 0.044334] regulator-dummy: no parameters
[ 0.049093] NET: Registered protocol family 16
[ 0.049594] DMA: preallocated 256 KiB pool for atomic coherent
allocations
[ 0.051228] cpuidle: using governor ladder
[ 0.051777] Feroceon L2: Enabling L2
[ 0.051825] Feroceon L2: Cache support initialised.
[ 0.052148] [Firmware Info]: /ocp@f1000000/ethernet-
controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.052266] [Firmware Info]: /ocp@f1000000/ethernet-
controller@76000/ethernet1-port@0: local-mac-address is not set
[ 0.062452] SCSI subsystem initialized
[ 0.062905] usbcore: registered new interface driver usbfs
[ 0.063015] usbcore: registered new interface driver hub
[ 0.063101] usbcore: registered new device driver usb
[ 0.064405] Switched to clocksource orion_clocksource
[ 0.065779] NET: Registered protocol family 2
[ 0.066731] TCP established hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.066764] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.066791] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.066849] TCP: reno registered
[ 0.066864] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.066891] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.067119] NET: Registered protocol family 1
[ 0.068330] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.069615] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.069640] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.069971] msgmni has been set to 116
[ 0.071867] io scheduler noop registered
[ 0.071891] io scheduler deadline registered (default)
[ 0.073435] kirkwood-pinctrl f1010000.pin-controller: registered
pinctrl driver
[ 0.074177] irq: Cannot allocate irq_descs @ IRQ31, assuming pre-
allocated
[ 0.074650] irq: Cannot allocate irq_descs @ IRQ63, assuming pre-
allocated
[ 0.075472] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus
0000:00
[ 0.075494] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 0.075512] pci_bus 0000:00: root bus resource [mem
0xe0000000-0xefffffff]
[ 0.075528] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.076109] PCI: bus0: Fast back to back transfers disabled
[ 0.076129] pci 0000:00:01.0: bridge configuration invalid ([bus
00-00]), reconfiguring
[ 0.076148] pci 0000:00:02.0: bridge configuration invalid ([bus
00-00]), reconfiguring
[ 0.076769] PCI: bus1: Fast back to back transfers disabled
[ 0.077414] PCI: bus2: Fast back to back transfers disabled
[ 0.077565] pci 0000:00:01.0: BAR 8: assigned [mem
0xe0000000-0xe00fffff]
[ 0.077587] pci 0000:00:02.0: BAR 8: assigned [mem
0xe0100000-0xe01fffff]
[ 0.077610] pci 0000:01:00.0: BAR 0: assigned [mem
0xe0000000-0xe000ffff 64bit]
[ 0.077645] pci 0000:01:00.0: BAR 2: assigned [mem
0xe0010000-0xe001ffff 64bit]
[ 0.077675] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.077693] pci 0000:00:01.0: bridge window [mem
0xe0000000-0xe00fffff]
[ 0.077718] pci 0000:02:00.0: BAR 0: assigned [mem
0xe0100000-0xe010ffff 64bit]
[ 0.077751] pci 0000:02:00.0: BAR 2: assigned [mem
0xe0110000-0xe011ffff 64bit]
[ 0.077780] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.077798] pci 0000:00:02.0: bridge window [mem
0xe0100000-0xe01fffff]
[ 0.120346] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.124292] console [ttyS0] disabled
[ 0.124382] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26,
base_baud = 12500000) is a 16550A
[ 0.668268] console [ttyS0] enabled
[ 0.673240] nand: device found, Manufacturer ID: 0xad, Chip ID: 0x76
[ 0.679654] nand: Hynix NAND 64MiB 3,3V 8-bit
[ 0.684037] nand: 64MiB, SLC, page size: 512, OOB size: 16
[ 0.689576] Scanning device for bad blocks
[ 1.133275] mtd: bad character after partition (f)
[ 1.138141] 8 ofpart partitions found on MTD device orion_nand
[ 1.143997] Creating 8 MTD partitions on "orion_nand":
[ 1.149184] 0x000000000000-0x000000080000 : "u-boot"
[ 1.155156] 0x000000080000-0x000000084000 : "u_env"
[ 1.160848] 0x000000084000-0x000000088000 : "s_env"
[ 1.166578] 0x000000200000-0x000001600000 : "kernel1"
[ 1.172929] 0x000000490000-0x000001600000 : "rootfs1"
[ 1.179259] 0x000001600000-0x000002a00000 : "kernel2"
[ 1.185650] 0x000001890000-0x000002a00000 : "ubi"
[ 1.191602] 0x000002a00000-0x000004000000 : "syscfg"
[ 1.198611] libphy: orion_mdio_bus: probed
[ 1.202922] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version
1.4
[ 1.211425] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC
address 00:50:43:00:02:02
[ 1.220961] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC
address 00:50:43:00:02:03
[ 1.229791] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.236380] ehci-pci: EHCI PCI platform driver
[ 1.240950] ehci-platform: EHCI generic platform driver
[ 1.246393] ehci-orion: EHCI orion driver
[ 1.250608] orion-ehci f1050000.ehci: EHCI Host Controller
[ 1.256178] orion-ehci f1050000.ehci: new USB bus registered, assigned
bus number 1
[ 1.264024] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 1.285179] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 1.329237] hub 1-0:1.0: USB hub found
[ 1.333191] hub 1-0:1.0: 1 port detected
[ 1.337985] usbcore: registered new interface driver usb-storage
[ 1.345426] TCP: cubic registered
[ 1.348850] NET: Registered protocol family 10
[ 1.354785] NET: Registered protocol family 17
[ 1.359313] bridge: automatic filtering via arp/ip/ip6tables has been
deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.372037] Bridge firewalling registered
[ 1.376269] 8021q: 802.1Q VLAN Support v1.8
[ 1.382474] UBI: auto-attach mtd6
[ 1.385854] UBI: attaching mtd6 to ubi0
[ 1.513934] UBI: scanning is finished
[ 1.528360] UBI: attached mtd6 (name "ubi", size 17 MiB) to ubi0
[ 1.534437] UBI: PEB size: 16384 bytes (16 KiB), LEB size: 15872 bytes
[ 1.540993] UBI: min./max. I/O unit sizes: 512/512, sub-page size 256
[ 1.547482] UBI: VID header offset: 256 (aligned 256), data offset: 512
[ 1.554125] UBI: good PEBs: 1116, bad PEBs: 0, corrupted PEBs: 0
[ 1.560177] UBI: user volume: 2, internal volumes: 1, max. volumes
count: 92
[ 1.567276] UBI: max/mean erase counter: 6/3, WL threshold: 4096, image
sequence number: 501326687
[ 1.576292] UBI: available PEBs: 0, total reserved PEBs: 1116, PEBs
reserved for bad PEB handling: 80
[ 1.586254] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[ 1.591596] ubiblock: device ubiblock0_0 (rootfs) set to be root
filesystem
[ 1.598871] UBI: background thread "ubi_bgt0d" started, PID 701
[ 1.608773] mvsw61xx 10.mvsw61xx: Found MV88E6171 at f1072004.mdio-
bu:10
[ 1.615536] mvsw61xx 10.mvsw61xx: Using indirect addressing
[ 1.621236] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.635661] VFS: Mounted root (squashfs filesystem) readonly on device
254:0.
[ 1.643276] Freeing unused kernel memory: 148K (c04bd000 - c04e2000)
[ 2.356771] init: Console is alive
[ 3.360945] init: - preinit -
[ 3.678352] random: procd urandom read with 30 bits of entropy
available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug
level
[ 6.811342] UBIFS: recovery needed
[ 6.815041] UBIFS: background thread "ubifs_bgt0_1" started, PID 850
[ 6.844694] UBIFS: recovery completed
[ 6.848469] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 6.854969] UBIFS: LEB size: 15872 bytes (15 KiB), min./max. I/O unit
sizes: 512 bytes/512 bytes
[ 6.863798] UBIFS: FS size: 14205440 bytes (13 MiB, 895 LEBs), journal
size 714240 bytes (0 MiB, 45 LEBs)
[ 6.873420] UBIFS: reserved for root: 670958 bytes (655 KiB)
[ 6.879128] UBIFS: media format: w4/r0 (latest is w4/r0), UUID
B59C04E2-0A96-4C39-B2C8-4B67CF99494E, small LPT model
[ 6.895156] mount_root: switching to jffs2 overlay
[ 6.912776] procd: - early -
[ 8.150975] procd: - ubus -
[ 9.175300] procd: - init -
Please press Enter to activate this console.
[ 10.586782] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.606027] i2c /dev entries driver
[ 10.618909] Loading modules backported from Linux version
master-2015-10-26-0-g28c26cb
[ 10.626906] Backport generated by backports.git
backports-20150903-4-g12cf266
[ 10.642702] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.654539] nf_conntrack version 0.5.0 (932 buckets, 3728 max)
[ 10.773827] xt_time: kernel timezone is -0000
[ 10.790786] cfg80211: World regulatory domain updated:
[ 10.795996] cfg80211: DFS Master region: unset
[ 10.800369] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.810177] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.818240] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.826295] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.834339] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000
KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 10.843886] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000
KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 10.853433] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 10.861576] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 10.869631] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 10.976808] Marvell TOPDOG(R) 802.11 Wireless Network Driver version
0.13
[ 10.983657] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 11.972069] ieee80211 phy0: Command RF_ANTENNA error 0x2
[ 11.977455] ieee80211 phy0: failed to set # of RX antennas
[ 11.993318] ieee80211 phy0: Command RF_ANTENNA error 0x2
[ 11.998713] ieee80211 phy0: failed to set # of TX antennas
[ 12.004243] ieee80211 phy0: 88w8366 v48, c8d719177244, STA firmware
4.1.0.3
[ 12.014008] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 12.827430] ieee80211 phy1: Command RF_ANTENNA error 0x2
[ 12.832782] ieee80211 phy1: failed to set # of RX antennas
[ 12.847515] ieee80211 phy1: Command RF_ANTENNA error 0x2
[ 12.852867] ieee80211 phy1: failed to set # of TX antennas
[ 12.858429] ieee80211 phy1: 88w8366 v48, c8d719177246, STA firmware
4.1.0.3
[ 12.874782] PPP generic driver version 2.4.2
[ 12.895794] NET: Registered protocol family 24
[ 18.763942] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000
Mb/s, full duplex, flow control disabled
[ 18.786938] device eth0 entered promiscuous mode
[ 18.797254] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 18.850206] mv643xx_eth_port mv643xx_eth_port.1 eth1: link up, 1000
Mb/s, full duplex, flow control disabled
[ 19.677949] cfg80211: Regulatory domain changed to country: US
[ 19.683816] cfg80211: DFS Master region: FCC
[ 19.688066] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 19.697880] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
3000 mBm), (N/A)
[ 19.705947] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000
KHz AUTO), (N/A, 2300 mBm), (N/A)
[ 19.715495] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000
KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 19.725041] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2300 mBm), (0 s)
[ 19.733175] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
3000 mBm), (N/A)
[ 19.741234] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
[ 19.775544] br-lan: port 1(eth0) entered forwarding state
[ 19.781013] br-lan: port 1(eth0) entered forwarding state
[ 19.794468] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 21.774457] br-lan: port 1(eth0) entered forwarding state
[ 22.308888] ieee80211 phy0: 88w8366 v7, c8d719177244, AP firmware
5.2.8.17
[ 22.385479] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 22.431030] device wlan0 entered promiscuous mode
[ 22.517451] 0000:02:00.0: unable to load firmware helper image
[ 22.523399] ieee80211 phy1: Cannot start firmware
[ 22.528230] ieee80211 phy1: Trying to reload the firmware again
[ 22.600166] random: nonblocking pool is initialized
[ 23.016669] ieee80211 phy1: 88w8366 v7, c8d719177246, AP firmware
5.2.8.17
[ 23.071158] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 23.080719] device wlan1 entered promiscuous mode
[ 23.085567] br-lan: port 3(wlan1) entered forwarding state
[ 23.091109] br-lan: port 3(wlan1) entered forwarding state
[ 23.394464] br-lan: port 3(wlan1) entered disabled state
[ 23.757510] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 23.764020] br-lan: port 3(wlan1) entered forwarding state
[ 23.769589] br-lan: port 3(wlan1) entered forwarding state
[ 23.970423] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 23.976977] br-lan: port 2(wlan0) entered forwarding state
[ 23.982525] br-lan: port 2(wlan0) entered forwarding state
[ 25.764425] br-lan: port 3(wlan1) entered forwarding state
[ 25.974417] br-lan: port 2(wlan0) entered forwarding state
--
Ticket URL: <https://dev.openwrt.org/ticket/21284#comment:9>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
