#21645: firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map
pages failed
-----------------------+------------------------
Reporter: anonymous | Owner: developers
Type: defect | Status: new
Priority: normal | Milestone:
Component: packages | Version: Trunk
Keywords: |
-----------------------+------------------------
I am on commit 6d3435ea1a21a8dc23e6098461210e9b675014da from the trunk.
I am unable to load the ath10k driver on an MR-1750:
[ 0.000000] MyLoader: sysp=f9d9b10b, boardp=99d9ab99, parts=8b99c12a
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem
0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 803afde0, node_mem_map
81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200
rootfstype=squashfs,jffs2 init=/etc/preinit board=MR1750 root=31:04
mtdparts=spi0.0:256k(u-boot),64k(u-boot-
env),384k(custom),1280k(kernel),6528k(rootfs),7808k(inactive),64k(ART)
mem=128M rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536
bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125532K/131072K available (2780K kernel code, 143K
rwdata, 572K rodata, 268K init, 195K bss, 5540K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:240.000MHz,
Ref:40.000MHz
[ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 5309056796 ns
[ 0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every
5965232126ns
[ 0.007492] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.070061] pid_max: default: 32768 minimum: 301
[ 0.074610] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080934] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.089821] clocksource jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.099710] NET: Registered protocol family 16
[ 0.104999] MIPS: machine is OpenMesh MR1750
[ 0.111728] registering PCI controller with io_map_base unset
[ 0.117319] ar724x-pci ar724x-pci.1: PCIe link is down
[ 0.122234] registering PCI controller with io_map_base unset
[ 0.349033] PCI host bridge to bus 0000:00
[ 0.352959] pci_bus 0000:00: root bus resource [mem
0x10000000-0x11ffffff]
[ 0.359554] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.364938] pci_bus 0000:00: root bus resource [??? 0x00000000 flags
0x0]
[ 0.371484] pci_bus 0000:00: No busn resource found for root bus, will
use [bus 00-ff]
[ 0.379170] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 0.379213] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff
64bit]
[ 0.379267] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff
pref]
[ 0.379317] pci 0000:00:00.0: supports D1
[ 0.379330] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.379515] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.379543] pci 0000:00:00.0: BAR 0: assigned [mem
0x10000000-0x101fffff 64bit]
[ 0.386555] pci 0000:00:00.0: BAR 6: assigned [mem
0x10200000-0x1020ffff pref]
[ 0.393635] PCI host bridge to bus 0000:01
[ 0.397528] pci_bus 0000:01: root bus resource [mem
0x12000000-0x13ffffff]
[ 0.404173] pci_bus 0000:01: root bus resource [io 0x0001]
[ 0.409535] pci_bus 0000:01: root bus resource [??? 0x00000000 flags
0x0]
[ 0.416094] pci_bus 0000:01: No busn resource found for root bus, will
use [bus 01-ff]
[ 0.423748] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.423766] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.429131] Switched to clocksource MIPS
[ 0.433876] NET: Registered protocol family 2
[ 0.438734] TCP established hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.445430] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.451553] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.457730] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.463337] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.469582] NET: Registered protocol family 1
[ 0.473777] PCI: CLS 0 bytes, default 32
[ 0.474591] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.493814] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.499424] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.511035] io scheduler noop registered
[ 0.514757] io scheduler deadline registered (default)
[ 0.519927] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.526330] console [ttyS0] disabled
[ 0.549783] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud
= 2500000) is a 16550A
[ 0.558045] console [ttyS0] enabled
[ 0.565088] bootconsole [early0] disabled
[ 0.575291] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.581182] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.586325] 7 cmdlinepart partitions found on MTD device spi0.0
[ 0.592336] Creating 7 MTD partitions on "spi0.0":
[ 0.597195] 0x000000000000-0x000000040000 : "u-boot"
[ 0.602937] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.608938] 0x000000050000-0x0000000b0000 : "custom"
[ 0.614644] 0x0000000b0000-0x0000001f0000 : "kernel"
[ 0.620328] 0x0000001f0000-0x000000850000 : "rootfs"
[ 0.625967] mtd: device 4 (rootfs) set to be root filesystem
[ 0.631800] 1 squashfs-split partitions found on MTD device rootfs
[ 0.638072] 0x000000640000-0x000000850000 : "rootfs_data"
[ 0.644205] 0x000000850000-0x000000ff0000 : "inactive"
[ 0.650082] 0x000000ff0000-0x000001000000 : "ART"
[ 0.672062] libphy: ag71xx_mdio: probed
[ 1.339591] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:05
[uid=004dd072, driver=Atheros 8035 ethernet]
[ 1.350292] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 1.358392] NET: Registered protocol family 10
[ 1.365860] NET: Registered protocol family 17
[ 1.370480] bridge: automatic filtering via arp/ip/ip6tables has been
deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.383389] 8021q: 802.1Q VLAN Support v1.8
[ 1.394088] VFS: Mounted root (squashfs filesystem) readonly on device
31:4.
[ 1.402233] Freeing unused kernel memory: 268K (803cd000 - 80410000)
[ 2.411868] init: Console is alive
[ 2.415483] init: - watchdog -
[ 3.566518] usbcore: registered new interface driver usbfs
[ 3.572200] usbcore: registered new interface driver hub
[ 3.577652] usbcore: registered new device driver usb
[ 3.586962] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.594719] ehci-platform: EHCI generic platform driver
[ 3.602243] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.609485] ohci-platform: OHCI generic platform driver
[ 4.440049] init: - preinit -
[ 5.019622] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.043825] random: procd urandom read with 7 bits of entropy available
[ 7.246873] jffs2: notice: (339) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of
xref (0 dead, 0 orphan) found.
[ 7.264528] mount_root: switching to jffs2 overlay
[ 7.433414] procd: - early -
[ 7.436415] procd: - watchdog -
[ 8.134379] procd: - ubus -
[ 9.142511] procd: - init -
[ 9.706526] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.720683] Netfilter messages via NETLINK v0.30.
[ 9.727791] ip_set: protocol 6
[ 9.757453] Loading modules backported from Linux version
v4.4-rc5-1913-gc8fdf68
[ 9.765002] Backport generated by backports.git
backports-20151218-0-g2f58d9d
[ 9.852088] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 9.858266] ath10k_pci 0000:00:00.0: pci irq legacy interrupts 0
irq_mode 0 reset_mode 0
[ 10.319894] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c
chip_id 0x043202ff sub 0000:0000
[ 10.329288] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing
0 dfs 1 testmode 1
[ 10.342365] ath10k_pci 0000:00:00.0: firmware ver 10.2.4.97 api 5
features no-p2p crc32 f91e34f2
[ 10.391460] ath10k_pci 0000:00:00.0: Direct firmware load for
ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 10.402065] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 10.477727] firmware ath10k!QCA988X!hw2.0!board-2.bin:
firmware_loading_store: map pages failed
[ 10.503065] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32
bebc7c08
[ 11.557377] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal
file max-sta 128 raw 0 hwcrypto 1
[ 11.662168] ath: EEPROM regdomain: 0x0
[ 11.662183] ath: EEPROM indicates default country code should be used
[ 11.662191] ath: doing EEPROM country->regdmn map search
[ 11.662207] ath: country maps to regdmn code: 0x3a
[ 11.662215] ath: Country alpha2 being used: US
[ 11.662222] ath: Regpair used: 0x3a
[ 11.819659] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.834131] nf_conntrack version 0.5.0 (1965 buckets, 7860 max)
[ 11.866782] xt_time: kernel timezone is -0000
[ 11.884300] PPP generic driver version 2.4.2
[ 11.890839] NET: Registered protocol family 24
[ 11.908485] ath: EEPROM regdomain: 0x0
[ 11.908501] ath: EEPROM indicates default country code should be used
[ 11.908508] ath: doing EEPROM country->regdmn map search
[ 11.908524] ath: country maps to regdmn code: 0x3a
[ 11.908533] ath: Country alpha2 being used: US
[ 11.908540] ath: Regpair used: 0x3a
[ 11.921907] ieee80211 phy1: Selected rate control algorithm
'minstrel_ht'
[ 11.924304] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[ 18.725471] device eth0 entered promiscuous mode
[ 18.740082] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 19.461049] eth0: link up (1000Mbps/Full duplex)
[ 19.465777] br-lan: port 1(eth0) entered forwarding state
[ 19.471310] br-lan: port 1(eth0) entered forwarding state
[ 19.553669] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 21.469152] br-lan: port 1(eth0) entered forwarding state
[ 22.203750] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 22.232951] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 22.246662] device wlan0 entered promiscuous mode
[ 22.257600] device wlan1 entered promiscuous mode
[ 22.558109] device wlan0 left promiscuous mode
[ 22.562729] br-lan: port 2(wlan0) entered disabled state
[ 23.924009] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 24.041433] device wlan0 entered promiscuous mode
[ 24.307273] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 24.313897] br-lan: port 3(wlan1) entered forwarding state
[ 24.319522] br-lan: port 3(wlan1) entered forwarding state
[ 26.319177] br-lan: port 3(wlan1) entered forwarding state
[ 26.699417] ath10k_pci 0000:00:00.0: no channel configured; ignoring
frame(s)!
[ 28.060067] ath10k_pci 0000:00:00.0: no channel configured; ignoring
frame(s)!
[ 28.067453] ath10k_pci 0000:00:00.0: no channel configured; ignoring
frame(s)!
[ 28.366981] ath10k_pci 0000:00:00.0: no channel configured; ignoring
frame(s)!
[ 29.135983] ath10k_pci 0000:00:00.0: no channel configured; ignoring
frame(s)!
[ 29.160977] ath10k_pci 0000:00:00.0: no channel configured; ignoring
frame(s)!
[ 29.185972] ath10k_pci 0000:00:00.0: no channel configured; ignoring
frame(s)!
[ 29.236098] ath10k_pci 0000:00:00.0: no channel configured; ignoring
frame(s)!
[ 29.243494] ath10k_pci 0000:00:00.0: no channel configured; ignoring
frame(s)!
[ 29.368003] ath10k_pci 0000:00:00.0: no channel configured; ignoring
frame(s)!
[ 49.030794] random: nonblocking pool is initialized
--
Ticket URL: <https://dev.openwrt.org/ticket/21645>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
