I'm running HEAD on a wrt54gs v1.1 and anytime traffic flows over the
WLAN the kernel panics. Any ideas as to my next step?
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Nov 25 13:12:58 CST 2004 (r...@me)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena.
Initializing Devices.
No DPN
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.60.13.0
rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
CPU type 0x29007: 300MHz
Total memory: 0x2000000 bytes (32MB)
Total memory used by CFE: 0x80300000 - 0x8043EB40 (1305408)
Initialized Data: 0x80338DB0 - 0x8033B160 (9136)
BSS Area: 0x8033B160 - 0x8033CB40 (6624)
Local Heap: 0x8033CB40 - 0x8043CB40 (1048576)
Stack Area: 0x8043CB40 - 0x8043EB40 (8192)
Text (code) segment: 0x80300000 - 0x80338DB0 (232880)
Boot area (physical): 0x0043F000 - 0x0047F000
Relocation Factor: I:00000000 - D:00000000
Boot version: v3.4
The boot is CFE
mac_init(): Find mac [00:13:10:07:EE:FC] in location 0
Nothing...
eou_key_init(): Find key pair in location 0
The eou device id is same
The eou public key is same
The eou private key is same
Device eth0: hwaddr 00-13-10-07-EE-FC, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Reading :: Failed.: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3768 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.28.9 (we...@lappy) (gcc version 4.1.2) #4 Sun Mar 29 23:51:58
EDT 2009
console [early0] enabled
CPU revision is: 00029007 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x09, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x07, vendor 0x4243)
ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243)
ssb: Core 3 found: USB 1.1 Device (cc 0x818, rev 0x01, vendor 0x4243)
ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x01, vendor 0x4243)
ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x01, vendor 0x4243)
ssb: Core 6 found: MEMC SDRAM (cc 0x80F, rev 0x01, vendor 0x4243)
ssb: Core 7 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243)
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0812, irq 2 => 2
ssb: set_irq: core 0x0806, irq 3 => 3
ssb: set_irq: core 0x0817, irq 0 => 4
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2
init=/etc/preinit noinitrd console=ttyS0,115200
Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 4kB, 2-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 128 (order: 7, 512 bytes)
console handover: boot [early0] -> real [ttyS0]
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29856k/32768k available (2036k kernel code, 2912k reserved, 312k data,
128k init, 0k highmem)
Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
Mount-cache hash table entries: 512
net_namespace: 480 bytes
NET: Registered protocol family 16
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
detected lzma initramfs
initramfs: LZMA lc=1,lp=2,pb=2,origSize=512
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
serial8250 serial8250.0: unable to register port at index 0 (IO0 MEMb8000300
IRQ3): -28
serial8250 serial8250.0: unable to register port at index 1 (IO0 MEMb8000400
IRQ3): -28
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:13:10:07:ee:fc
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Flash device: 0x800000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x007e0000 : "linux"
0x000fe800-0x007e0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force
read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=3E0000, len=400000
0x003e0000-0x007e0000 : "rootfs_data"
0x007e0000-0x00800000 : "nvram"
TCP vegas registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
- preinit -
Press CTRL-C for failsafe
diag: Detected 'Linksys WRT54G/GS/GL'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found!
b44: eth0: powering down PHY
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -
Please press Enter to activate this console. b44: eth0: Link is up at 100 Mbps,
full duplex.
b44: eth0: Flow control is off for TX and off for RX.
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: topology change detected, propagating
br-lan: port 1(eth0.0) entering forwarding state
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
PPP generic driver version 2.4.2
NET: Registered protocol family 24
b43-phy0: Broadcom 4712 WLAN found (core revision 7)
Broadcom 43xx driver loaded [ Features: PLR, Firmware-ID: FW13 ]
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (512 buckets, 2048 max)
br-lan: port 1(eth0.0) entering disabled state
br-lan: topology change detected, propagating
br-lan: port 1(eth0.0) entering forwarding state
input: b43-phy0 as /devices/virtual/input/input0
b43 ssb0:0: firmware: requesting b43/ucode5.fw
b43 ssb0:0: firmware: requesting b43/pcm5.fw
b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw
b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
b43-phy0: Radio turned on by software
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering disabled state
input: b43-phy0 as /devices/virtual/input/input1
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
br-lan: topology change detected, propagating
br-lan: port 2(wlan0) entering forwarding state
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc
== 8017aa30, ra == c024fc78
Oops[#1]:
Cpu 0
$ 0 : 00000000 1000b800 00000000 00000040
$ 4 : 81f714c0 80c19b40 1000b801 000000ff
$ 8 : 80c5e044 81f71000 00000000 00000980
$12 : ffffffb9 0000002a 00000007 000000bc
$16 : 80c19b40 81f71380 81e951c0 81f45d70
$20 : 80c19b40 00000000 00000002 81f71000
$24 : 00000000 c025e8a0
$28 : 81f44000 81f45ce8 00000000 c024fc78
Hi : fffff970
Lo : 00000690
epc : 8017aa30 0x8017aa30
Not tainted
ra : c024fc78 0xc024fc78
Status: 1000b802 KERNEL EXL
Cause : 0080000c
BadVA : 00000000
PrId : 00029007 (Broadcom BCM3302)
Modules linked in: xt_TARPIT nf_nat_tftp nf_conntrack_tftp nf_nat_irc
nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp xt_quota xt_pkttype iptable_raw
compat_xtg
Process miniupnpd (pid: 1016, threadinfo=81f44000, task=81fb6ab8, tls=00000000)
Stack : 80c5e034 81f45d70 80c19b40 00000000 81f71000 00000040 80c5e034 c025e58c
81f45d70 00000980 ffffffb9 000000bc 0000003c 00000000 00000000 00000000
00000040 81e951c0 00000000 00000040 81e957d4 81f71380 80c5e034 80c19b40
81e951c0 0048b494 00000002 00000000 00000000 c025eae0 81f71380 80c199c0
81f45dd0 00000018 80c19b40 81f71000 81e951c0 81f71380 00000000 00000000
...
Call Trace:[<c025e58c>] 0xc025e58c
[<c025eae0>] 0xc025eae0
[<c0247768>] 0xc0247768
[<80027f00>] 0x80027f00
[<80032698>] 0x80032698
[<800320b0>] 0x800320b0
[<800477c0>] 0x800477c0
[<800321c8>] 0x800321c8
[<8000d138>] 0x8000d138
[<80048720>] 0x80048720
[<80048558>] 0x80048558
[<80185430>] 0x80185430
[<80001444>] 0x80001444
[<8005989c>] 0x8005989c
[<80002368>] 0x80002368
Code: 8c820004 aca40000 aca20004 <ac450000> 8c820008 ac850004 24420001
ac820008 40016000
Kernel panic - not syncing: Fatal exception in interrupt
_______________________________________________
openwrt-users mailing list
[email protected]
https://lists.openwrt.org/mailman/listinfo/openwrt-users
