Hi Bernard.
I reinstalled our cluster to see if the problem of swap partition
persists. I use Scientific Linux 4.1 and OSCAR 4.2.
The problem is the id of the swap partition in the nodes, it is 83
(linux) instead of 82 (swap). The system reports the right amount (4GB)
of "swap partition" when I use commands like "top" or "free", but when
I look with fdisk, it lists as "Linux partition"
Below are my autoinstallscript.conf and the partition layout in one of
the nodes (nanomol01). The swap partition should be /dev/hda5.
Thanks for your attention.
Marcelo
===========================================================
[EMAIL PROTECTED] mpi]$ more
/var/lib/systemimager/images/oscarimage/etc/systemimager/autoinstallscript.conf
<!--
This autoinstallscript.conf file was generated by SystemInstaller
for use by SystemImager when creating the autoinstall script.
This file generated at: 2006-9-5 15:10:50
from: /opt/oscar/scripts//opt/oscar/oscarsamples/ide.disk
Image directory: /var/lib/systemimager/images/oscarimage
-->
<config>
<disk dev="/dev/hda" label_type="msdos" unit_of_measurement="MB">
<part num="1" size="24" p_type="primary" />
<part num="2" size="10000" p_type="primary" />
<part num="3" size="*" p_type="extended" />
<part num="5" size="4096" p_type="logical" />
<part num="6" size="*" p_type="logical" />
</disk>
<fsinfo line="100" real_dev="/dev/hda2" mp="/" fs="ext3"
options="defaults" dump="1" pass="2" />
<fsinfo line="101" real_dev="/dev/hda5" mp="swap" fs="swap"
options="defaults" dump="0" pass="0" />
<fsinfo line="102" real_dev="/dev/hda6" mp="/backup" fs="ext3"
options="defaults" dump="1" pass="2" />
<fsinfo line="103" real_dev="/dev/hda1" mp="/boot" fs="ext3"
options="defaults" dump="1" pass="2" />
<fsinfo line="104" real_dev="/dev/fd0" mp="/mnt/floppy"
fs="auto" options="noauto,owner" dump="0" pass="0" />
<fsinfo line="105" real_dev="none" mp="/dev/pts" fs="devpts"
options="defaults" dump="0" pass="0" />
<fsinfo line="106" real_dev="none" mp="/proc" fs="proc"
options="defaults" dump="0" pass="0" />
<fsinfo line="107" real_dev="nfs_oscar:/home" mp="/home"
fs="nfs" options="rw" dump="0" pass="0" />
<boel devstyle="devfs" />
</config>
=================================================================
[EMAIL PROTECTED] ~]# fdisk /dev/hda
The number of cylinders for this disk is set to 4863.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): p
Disk /dev/hda: 40.0 GB, 40000000000 bytes
255 heads, 63 sectors/track, 4863 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 1 3 24066 83 Linux
/dev/hda2 4 1278 10241437+ 83 Linux
/dev/hda3 1279 4863 28796512+ 5 Extended
/dev/hda5 1279 1800 4192933+ 83 Linux
/dev/hda6 1801 4863 24603516 83 Linux
Bernard Li wrote:
> Hi Marcelo:
>
> I'm not exactly sure what you mean - If you re-create a new image with
> the original name (that have clients associated with it), then it
> should all work out - what exactly can't you "do again"?
>
> See the section on "Deleting node images" on how to properly do it:
>
> http://svn.oscar.openclustergroup.org/wiki/oscar:5.0:install_guide:ch5.14_deleting_clients
>
> Cheers,
>
> Bernard
>
> ------------------------------------------------------------------------
> *From:* [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
> *Sent:* Thu 17/08/2006 16:05
> *To:* Bernard Li
> *Subject:* RE: [Oscar-users] How to re-install just the processing nodes?
>
> Hi Bernard
>
> I made a terrible mistake. I deleted the directory with the image. I
> tryed to
> edit the file that you asked but take no effect, then I tryed to
> remake the
> image (oscar_wizard), but I misspelled the name and end with two images.
> Finally I thought if I erase both images, I could do it again, but I
> was wrong.
> I don't know if there is anything we can do, besides reinstall the
> system. Any
> hint?
>
> Thanks for your attention.
>
> Marcelo
>
>
> Quoting Bernard Li <[EMAIL PROTECTED]>:
>
> > Look in:
> >
> >
> /var/lib/systemimager/images/<image_name>/etc/systemimager/autoinstallscript.conf
> >
> > P.S. Can you please put your response at the top instead of at the
> bottom, it
> > makes it eaiser to read.
> >
> > Thanks,
> >
> > Bernard
> >
> >
> > -----Original Message-----
> > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
> > Sent: Wed 16/08/2006 14:00
> > To: [email protected]; Bernard Li
> > Cc: [email protected]
> > Subject: Re: [Oscar-users] How to re-install just the processing nodes?
> >
> > Quoting Bernard Li <[EMAIL PROTECTED]>:
> >
> > > Hi Marcelo:
> > >
> > > That is very strange - can you post your image's
> > > /etc/systemimager/autoinstallscript.conf?
> > >
> > > Cheers,
> > >
> > > Bernard
> > >
> > >
> > > -----Original Message-----
> > > From: [EMAIL PROTECTED] on behalf of
> > > [EMAIL PROTECTED]
> > > Sent: Wed 16/08/2006 09:10
> > > To: [email protected]
> > > Subject: Re: [Oscar-users] How to re-install just the processing
> nodes?
> > >
> > > Quoting Bernard Li <[EMAIL PROTECTED]>:
> > >
> > > > Hi Marcelo:
> > > >
> > > > This is actually very easy. First modify your SystemImager
> > > > autoinstallscript.conf for that image:
> > > >
> > > >
> > >
> >
> /var/lib/systemimager/images/<image_name>/etc/systemimager/autoinstallscript.conf
> > > >
> > > > Edit it such that you have the correct amount of swap space.
> > > >
> > > > Then reboot your node(s) such that it'll re-install the image.
> > > >
> > > > Re-run the "Complete cluster setup" after the new node is imaged and
> > > > rebooted.
> > > >
> > > > One trick we often use to force the nodes to re-image is execute
> a cexec
> > > > command to corrupt the MBR so that it won't be able to boot from
> the HD:
> > > >
> > > > cexec 'dd if=/dev/zero of=/dev/???'
> > > >
> > > > Replace '???' with the drive designation. **Note** Only do this
> if you
> > > have
> > > > backed up everything from your client nodes...
> > > >
> > > > Cheers,
> > > >
> > > > Bernard
> > > >
> > > >
> > > > -----Original Message-----
> > > > From: [EMAIL PROTECTED] on behalf of
> > > > [EMAIL PROTECTED]
> > > > Sent: Mon 14/08/2006 13:46
> > > > To: [email protected]
> > > > Subject: [Oscar-users] How to re-install just the processing nodes?
> > > >
> > > > Hi.
> > > >
> > > > I would like to re-install the processing nodes because I
> thing that
> > the
> > > > virtual memory (128MB) is to low. Could I just start at step 4
> of the
> > > OSCAR
> > > > 4.2
> > > > wizard?
> > > >
> > > > Thanks
> > > >
> > > > Marcelo Garcia
> > > >
> > > >
> > > >
> >
> -------------------------------------------------------------------------
> > > > Using Tomcat but need to do more? Need to support web services,
> > security?
> > > > Get stuff done quickly with pre-integrated technology to make
> your job
> > > > easier
> > > > Download IBM WebSphere Application Server v.1.0.1 based on Apache
> > Geronimo
> > > >
> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
> <http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642>
> > > > _______________________________________________
> > > > Oscar-users mailing list
> > > > [email protected]
> > > > https://lists.sourceforge.net/lists/listinfo/oscar-users
> > > >
> > > >
> > >
> > >
> > > Hi Bernard and Michael.
> > >
> > > Looking for partition table of the nodes, something curious is that
> > there
> > > is
> > > no swap partition. The file in the systemimager directory and
> > > ${OSCARHOME}/oscarsamples/ide.disk say that /dev/hda5 should be
> the swap
> > > partition (id 82).
> > >
> > > Thanks for your attention
> > >
> > >
> > > ==================== Node partition table ======================
> > > [EMAIL PROTECTED] ~]# fdisk /dev/hda
> > >
> > > The number of cylinders for this disk is set to 4863.
> > > There is nothing wrong with that, but this is larger than 1024,
> > > and could in certain setups cause problems with:
> > > 1) software that runs at boot time (e.g., old versions of LILO)
> > > 2) booting and partitioning software from other OSs
> > > (e.g., DOS FDISK, OS/2 FDISK)
> > >
> > > Command (m for help): p
> > >
> > > Disk /dev/hda: 40.0 GB, 40000000000 bytes
> > > 255 heads, 63 sectors/track, 4863 cylinders
> > > Units = cylinders of 16065 * 512 = 8225280 bytes
> > >
> > > Device Boot Start End Blocks Id System
> > > /dev/hda1 1 3 24066 83 Linux
> > > /dev/hda2 4 4863 39037950 5 Extended
> > > /dev/hda5 4 19 128488+ 83 Linux
> > > /dev/hda6 20 4863 38909398+ 83 Linux
> > > ==================== Node partition table ======================
> > >
> > > ==================== ide.disk ======================
> > > [EMAIL PROTECTED] ~]# more /opt/oscar/oscarsamples/ide.disk
> > > /dev/hda1 24 ext3 /boot defaults
> > > /dev/hda5 4096 swap
> > > /dev/hda6 * ext3 / defaults
> > > nfs_oscar:/home - nfs /home rw
> > > nfs_oscar:/opt - nfs /opt rw
> > > [EMAIL PROTECTED] ~]#
> > > ==================== ide.disk ======================
> > >
> > >
> > >
> -------------------------------------------------------------------------
> > > Using Tomcat but need to do more? Need to support web services,
> security?
> > > Get stuff done quickly with pre-integrated technology to make your job
> > > easier
> > > Download IBM WebSphere Application Server v.1.0.1 based on Apache
> Geronimo
> > >
> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
> <http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642>
> > > _______________________________________________
> > > Oscar-users mailing list
> > > [email protected]
> > > https://lists.sourceforge.net/lists/listinfo/oscar-users
> > >
> > >
> >
> > Hi Bernard.
> >
> > In my /etc/systemimager there is no autoinstallscript.conf. There is a
> > autoinstallscript.template and a systemimager.conf. I will post both
> below.
> >
> > Marcelo
> >
> > ======================== autoinstallscript.template
> > ==========================
> > #!/bin/sh
> > #
> > # "SystemImager"
> > #
> > # Copyright (C) 1999-2004 Brian Elliott Finley
> > #
> > # 28.07.2005 Erich Focht : SCSI device detection and generation of
> > # /a/etc/systemconfig/hardware.lst
> > #
> > # David N. Lombard : Disks enumeration and disk editing
> > #
> > # $Id: autoinstallscript.template 3226 2005-08-09 10:24:55Z arighi $
> > #
> >
> > ##VERSION_INFO##
> >
> > # Load functions and other variables
> > . /etc/init.d/functions
> >
> > get_arch
> >
> > ##NO_LISTING##
> > if [ -z $NO_LISTING ]; then
> > VERBOSE_OPT="v"
> > else
> > VERBOSE_OPT=""
> > fi
> >
> > # Pull in variables left behind by the linuxrc script.
> > # This information is passed from the linuxrc script on the
> autoinstall media
> >
> > # via /tmp/variables.txt. Apparently the shell we use in BOEL is not
> > # intelligent enough to take a "set -a" parameter.
> > #
> > . /tmp/variables.txt || shellout
> >
> > ##SET_IMAGENAME##
> > ##SET_OVERRIDES##
> >
> > ### BEGIN Check to be sure this not run from a working machine ###
> > # Test for mounted SCSI or IDE disks
> > mount | grep [hs]d[a-z][1-9] > /dev/null 2>&1
> > [ $? -eq 0 ] && logmsg Sorry. Must not run on a working machine... &&
> > shellout
> >
> > # Test for mounted software RAID devices
> > mount | grep md[0-9] > /dev/null 2>&1
> > [ $? -eq 0 ] && logmsg Sorry. Must not run on a working machine... &&
> > shellout
> >
> > # Test for mounted hardware RAID disks
> > mount | grep c[0-9]+d[0-9]+p > /dev/null 2>&1
> > [ $? -eq 0 ] && logmsg Sorry. Must not run on a working machine... &&
> > shellout
> > ### END Check to be sure this not run from a working machine ###
> >
> >
> >
> ################################################################################
> > #
> > # Stop RAID devices before partitioning begins
> > #
> > # Q1) Why did they get started in the first place?
> > # A1) So we can pull a local.cfg file off a root mounted software RAID
> > system.
> > # They may not be started on your system -- they would only be
> started
> > if
> > # you did the stuff in Q3 below.
> > #
> > # Q2) Why didn't my local.cfg on my root mounted software RAID work
> for me
> > # with the standard kernel flavour?
> > # A2) The standard kernel flavour uses modules for the software RAID
> drivers
> > --
> > # therefore, software RAID is not available at the point in the boot
> > process
> > # where BOEL needs to read the local.cfg file. They are only
> pulled over
> >
> > # when this script is run, which is, of course, only runnable if
> it was
> > # pulled over the network using the settings that you would have
> wanted
> > it
> > # to get from the local.cfg file, which it couldn't. Right?
> > #
> > # Q3) Whatever. So how do I make it work with a local.cfg file on
> my root
> > # mounted software RAID?
> > # A3) Compile an autoinstall kernel with software RAID, and any
> other drivers
> >
> > # you might need built in (filesystem, SCSI drivers, etc.).
> > #
> > if [ -f /proc/mdstat ]; then
> > RAID_DEVICES=` cat /proc/mdstat | grep ^md | sed 's/ .*$//g' `
> >
> > # raidstop will not run unless a raidtab file exists
> > echo "" >> /etc/raidtab || shellout
> >
> > # turn dem pesky raid devices off!
> > for RAID_DEVICE in ${RAID_DEVICES}
> > do
> > DEV="/dev/${RAID_DEVICE}"
> > # we don't do a shellout here because, well I forgot why, but we
> don't.
> > logmsg "raidstop ${DEV}" && raidstop ${DEV}
> > done
> > fi
> > #
> >
> ################################################################################
> >
> >
> ################################################################################
> > # BEGIN disk enumeration
> > #
> > # Note the kludgey way to get /dev/sd* and /dev/*/c*d* to sort
> properly...
> > #
> > echo DISKORDER=${DISKORDER=sd,cciss,ida,rd,hd}
> > [ -z $DISKORDER ] || {
> > echo enumerate_disks
> > order=`echo "$DISKORDER" | sed 's/ /,/g' | sed s/,,*/,/g | sed s/^,//`
> > DISKS=0
> > while : ; do
> > [ -z $order ] && break
> > type=`expr $order : '\([^,]*\),' \| $order`
> > case $type in
> > cciss | ida | rd )
> > rest=
> > [ $type = rd ] && rest="8 9 10 11 12 13 14 15"
> > for c in 0 1 2 3 4 5 6 7 $rest ; do
> > for dev in `ls /dev/$type/c${c}d[0-9] 2>/dev/null` ; do
> > echo " $dev"
> > eval DISK$DISKS=${dev}
> > DISKS=`expr $DISKS + 1`
> > done
> > for dev in `ls /dev/$type/c${c}d[0-9][0-9] 2>/dev/null` ; do
> > echo " $dev"
> > eval DISK$DISKS=${dev}
> > DISKS=`expr $DISKS + 1`
> > done
> > done
> > ;;
> > hd )
> > for dev in `ls /dev/$type[a-z] 2>/dev/null` ; do
> > echo " $dev"
> > eval DISK$DISKS=$dev
> > DISKS=`expr $DISKS + 1`
> > done
> > ;;
> > sd )
> > for dev in `ls /dev/$type[a-z] 2>/dev/null` ; do
> > echo " $dev"
> > eval DISK$DISKS=$dev
> > DISKS=`expr $DISKS + 1`
> > done
> > for dev in `ls /dev/$type[a-z][a-z] 2>/dev/null` ; do
> > echo " $dev"
> > eval DISK$DISKS=$dev
> > DISKS=`expr $DISKS + 1`
> > done
> > ;;
> > * )
> > echo "type='$type'"
> > shellout
> > ;;
> > esac
> > order=`expr $order : '[^,]*,\(.*\)'`
> > done
> > echo DISKS=$DISKS
> > [ $DISKS -eq 0 ] && {
> > beep
> > beep
> > echo ""
> > echo "NO DISK DEVICE FILES WERE FOUND. THIS USUALLY MEANS THE
> KERNEL
> > DID
> > NOT"
> > echo "RECOGNIZE ANY OF THE ATTACHED DISKS."
> > echo ""
> > echo "The kernel boot messages, which preceded this, may
> indicate why."
> > echo ""
> > echo "Reverting to disk configuration specified by image master
> script."
> > DISKORDER=
> > echo ""
> > }
> > echo
> > beep
> > }
> > #
> > # END disk enumeration
> >
> ################################################################################
> >
> > ##PARTITION_DISKS##
> >
> > logmsg "Load additional filesystem drivers."
> > modprobe reiserfs
> > modprobe ext2
> > modprobe ext3
> > modprobe jfs
> > modprobe xfs
> >
> > logmsg "Load device mapper driver (for LVM)."
> > modprobe dm-mod
> >
> > ### BEGIN LVM initialization commands -AR- ###
> > ##INITIALIZE_LVM_PARTITIONS##
> > ### END LVM initialization commands ###
> >
> > ### BEGIN LVM groups creation commands -AR- ###
> > ##CREATE_LVM_GROUPS##
> > ### END LVM groups creation commands ###
> >
> > ### BEGIN LVM volumes creation commands -AR- ###
> > ##CREATE_LVM_VOLUMES##
> > ### END LVM volumes creation commands ###
> >
> > ### BEGIN swap and filesystem creation commands ###
> > ##CREATE_FILESYSTEMS##
> > ### END swap and filesystem creation commands ###
> >
> > ### BEGIN mount proc in image for tools like System Configurator ###
> > logmsg "mkdir -p /a/proc || shellout"
> > mkdir -p /a/proc || shellout
> > logmsg "mount proc /a/proc -t proc -o defaults || shellout"
> > mount proc /a/proc -t proc -o defaults || shellout
> > ### END mount proc in image for tools like System Configurator ###
> >
> > ### BEGIN mount sysfs in image for tools that might be run during
> chroot ###
> > logmsg "mkdir -p /a/sys || shellout"
> > mkdir -p /a/sys || shellout
> > logmsg "mount sysfs /a/sys -t sysfs -o defaults || shellout"
> > mount sysfs /a/sys -t sysfs -o defaults || shellout
> > ### END mount sysfs in image for tools that might be run during
> chroot ###
> >
> >
> ################################################################################
> > #
> > # Lay the image down on the freshly formatted disk(s)
> > #
> > if [ ! -z $MONITOR_SERVER ]; then
> > start_report_task
> > fi
> >
> > if [ ! -z $FLAMETHROWER_DIRECTORY_PORTBASE ]; then
> >
> > # Use multicast
> > MODULE_NAME="${IMAGENAME}"
> > DIR=/a
> > RETRY=7
> > FLAMETHROWER_TARPIPE=y
> > flamethrower_client
> > else
> > # Use rsync
> > if [ $NO_LISTING ]; then
> > logmsg "Quietly installing image... "
> > start_spinner
> > fi
> > if [ "${TMPFS_STAGING}" = "yes" ]; then
> >
> > # Deposit image into tmpfs
> > DIR=/tmp/tmpfs_staging
> > logmsg
> > logmsg "TMPFS_STAGING=${TMPFS_STAGING} -- Staging in ${DIR}"
> > mkdir -p ${DIR}
> >
> > logmsg "rsync -aHS${VERBOSE_OPT} --exclude=lost+found/
> --numeric-ids
> > ${IMAGESERVER}::${IMAGENAME}/ ${DIR}/"
> > rsync -aHS${VERBOSE_OPT} --exclude=lost+found/ --numeric-ids
> > ${IMAGESERVER}::${IMAGENAME}/ ${DIR}/ || shellout
> >
> > # Move from staging in tmpfs to disk
> > rsync -aHS${VERBOSE_OPT} --exclude=lost+found/ --numeric-ids
> ${DIR}/
> > /a/
> > else
> > logmsg "rsync -aHS${VERBOSE_OPT} --exclude=lost+found/
> --numeric-ids
> > ${IMAGESERVER}::${IMAGENAME}/ /a/"
> > rsync -aHS${VERBOSE_OPT} --exclude=lost+found/ --numeric-ids
> > ${IMAGESERVER}::${IMAGENAME}/ /a/ || shellout
> > fi
> > fi
> >
> > beep
> >
> > #
> >
> ################################################################################
> >
> >
> > if [ $NO_LISTING ]; then
> > stop_spinner
> > fi
> >
> > # Leave notice of which image is installed on the client
> > echo $IMAGENAME > /a/etc/systemimager/IMAGE_LAST_SYNCED_TO || shellout
> >
> > if [ ! -z $MONITOR_SERVER ]; then
> > stop_report_task 100
> > fi
> >
> > ### BEGIN generate new fstab file from autoinstallscript.conf ###
> > ##GENERATE_FSTAB##
> > ### END generate new fstab file from autoinstallscript.conf ###
> >
> >
> ################################################################################
> > #
> > # Process override directories
> > #
> > for OVERRIDE in $OVERRIDES
> > do
> > if [ ! -z $FLAMETHROWER_DIRECTORY_PORTBASE ]; then
> > # Use multicast
> > MODULE_NAME="override_${OVERRIDE}"
> > DIR=/a
> > RETRY=7
> > FLAMETHROWER_TARPIPE=y
> > flamethrower_client
> > else
> > # Use rsync
> > logmsg "rsync -av --numeric-ids
> $IMAGESERVER::overrides/$OVERRIDE/
> > /a/"
> > rsync -av --numeric-ids $IMAGESERVER::overrides/$OVERRIDE/
> /a/ ||
> > logmsg
> > "Override directory $OVERRIDE doesn't seem to exist, but that may be
> OK."
> > fi
> > done
> >
> > beep
> >
> > #
> >
> ################################################################################
> >
> >
> ################################################################################
> > # BEGIN disk edits
> > #
> > [ -z $DISKORDER ] || {
> > echo "Editing files for actual disk configuration..."
> > ##SHOW_DISK_EDITS##
> > for file in /etc/fstab /etc/raidtab
> /etc/systemconfig/systemconfig.conf;
> > do
> > [ -f /a/$file ] || continue
> > echo " $file"
> > cp /a/$file /a/$file.image
> > cat /a/$file.image |
> > ##EDIT_DISK_NAMES##
> > cat > /a/$file
> > done
> > echo
> > beep
> > }
> > #
> > # END disk edits
> >
> ################################################################################
> >
> >
> > ##################################################################
> > #
> > # Uncomment the line below to leave your hostname blank.
> > # Certain distributions use this as an indication to take on the
> > # hostname provided by a DHCP server. The default is to have
> > # SystemConfigurator assign your clients the hostname that
> > # corresponds to the IP address the use during the install.
> > # (If you used to use the static_dhcp option, this is your man.)
> > #
> > #HOSTNAME=""
> >
> >
> >
> ################################################################################
> > #
> > # mount /dev /a/dev -o bind if needed
> > #
> > ##BOEL_DEVSTYLE##
> > #
> >
> ################################################################################
> >
> >
> >
> ################################################################################
> > #
> > # Detect scsi hardware and include the device IDs into the
> hardware.lst
> > # file used by systemconfigurator. Do nothing if the hardware.lst file
> > # already exists (which is a sign that it has been already prepared).
> > # Would be shorter if discover could return numerical device IDs...
> > #
> > if [ ! -f /a/etc/systemconfig/hardware.lst ]; then
> > SCSI_MODS=`discover -f "%m\n" scsi | grep -v ide-scsi | uniq`
> > for MOD in $SCSI_MODS; do
> > DEVID=`grep $MOD /proc/bus/pci/devices | cut -f 2 | sort | uniq`
> > for MYDEV in $DEVID; do
> > VENDOR=`echo $MYDEV | cut -b 1-4`
> > MODEL=`echo $MYDEV | cut -b 5-8`
> > echo "$VENDOR $MODEL scsi $MOD" >>
> /a/etc/systemconfig/hardware.lst
> > echo "Added SCSI device $VENDOR:$MODEL using module $MOD to
> > hardware.lst"
> > done
> > done
> > fi
> > #
> >
> ################################################################################
> >
> >
> ################################################################################
> > #
> > # System Configurator
> > #
> > # Configure the client's hardware, network interface, and boot loader.
> > #
> > ##SYSTEMCONFIGURATOR##
> > #
> >
> ################################################################################
> >
> >
> >
> ################################################################################
> > #
> > # Post Install Scripts
> > #
> > run_post_install_scripts
> > #
> >
> ################################################################################
> >
> >
> >
> ################################################################################
> > #
> > # Unmount filesystems
> > #
> > ##UMOUNT_FILESYSTEMS##
> > #
> >
> ################################################################################
> >
> >
> >
> ################################################################################
> > #
> > # Tell the image server we're done
> > #
> > rsync $IMAGESERVER::scripts/imaging_complete > /dev/null 2>&1
> > #
> >
> ################################################################################
> >
> > # Take network interface down
> > [ -z $DEVICE ] && DEVICE=eth0
> > ifconfig $DEVICE down || shellout
> >
> > # Announce completion (even for non beep-incessantly --post-install
> options)
> > beep 3
> >
> > ##POSTINSTALL##
> > ======================== autoinstallscript.template
> > ==========================
> >
> > ======================== systemimager.conf ==========================
> > #
> > # "SystemImager"
> > #
> > # Copyright (C) 2002 Bald Guy Software
> <[EMAIL PROTECTED]>
> > #
> > # $Id: systemimager.conf 2045 2002-10-26 05:19:34Z brianfinley $
> > #
> >
> >
> ################################################################################
> > #
> > # The directory where images are stored by default.
> > #
> > DEFAULT_IMAGE_DIR = /var/lib/systemimager/images
> >
> >
> ################################################################################
> > #
> > # The directory where files needed by autoinstall clients are stored.
> > #
> > AUTOINSTALL_SCRIPT_DIR = /var/lib/systemimager/scripts
> >
> >
> ################################################################################
> > #
> > # The directory which contains the architecture specific directories
> where
> > # files needed by autoinstall clients are stored.
> > #
> > AUTOINSTALL_BOOT_DIR = /usr/share/systemimager/boot
> >
> >
> ################################################################################
> > #
> > # SystemImager's rsyncd.conf file.
> > #
> > RSYNCD_CONF = /etc/systemimager/rsyncd.conf
> >
> >
> ################################################################################
> > #
> > # The path to the directory where rsync stub files are stored.
> > #
> > RSYNC_STUB_DIR = /etc/systemimager/rsync_stubs
> >
> >
> ################################################################################
> > #
> > # Directory where tftp and net-boot files are stored
> > #
> > TFTP_DIR = /tftpboot
> >
> >
> ################################################################################
> > #
> > # This setting affects netbootmond. If set to LOCAL, then after
> successful
> > # completion of an install, a client's net boot configuration is
> modified to
> > # ensure future boots will happen from the client's local disk.
> > # NET_BOOT_DEFAULT can be set to local or net. Be sure to restart
> > # netbootmond after changing this setting (/etc/init.d/netbootmond
> restart).
> > #
> > NET_BOOT_DEFAULT = net
> > ======================== systemimager.conf ==========================
> >
> >
>
>
> ------------------------------------------------------------------------
>
> -------------------------------------------------------------------------
> Using Tomcat but need to do more? Need to support web services, security?
> Get stuff done quickly with pre-integrated technology to make your job easier
> Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
> ------------------------------------------------------------------------
>
> _______________________________________________
> Oscar-users mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/oscar-users
>
-------------------------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Oscar-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/oscar-users
